P&O Cruises Iona and Arvia S1000 Single colour no support required by Ukdavewood

Ukdavewood

Art>Sculptures

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

Arvia and Iona 0.2mm layer, 2 walls, 5% infill

Designer

16.8 h

2 plates

4.8(11)

Boost

241

Released

Description

Update 4/1/24. Underwater hull parts are now available too

- see multi coloured version of this model here https://makerworld.com/en/models/15006#profileId-14776

These models are a half size single colour reworks of my earlier 1:500 multi colour models.

Some minor support structures have been included within the models - see yellow and red colour coding in order to allow them to print without slicer supports.

I think it is ok to leave the yellow colour coded supports in place permanently - but I would recommend snipping off the red coded supports if you want to make the ship a little bit more authentic.

Prints in about 8 hrs on a Bambu Lab X1C 0.4mm nozzle, 0.2mm layer height.

STL files provided for each ship, plus pre-sliced Bambu Lab X1C/P1P 3mf print profile that contains both ships.

3 Test prints were done with Arvia - with the lighter green one in the photos being the final fully completed print.

6 Test prints were done on Iona - with the more complete model in BL PLA Silk Silver actually being the first test print - and having a few faults on it - which were gradually corrected with the smaller partial prints. It will print in PLA Silk - but some of the details like the little lamps on the top deck fail - so it is recommended just using Silver PLA - as per the last few partial prints.

Filament for the test prints was sponsored by Bambu Lab.

For background info about the development of these models see this forum thread.

https://forum.bambulab.com/t/cruise-ship-print/5122/73

For timelapes of Iona and Arvia - see this youtube video.

Youtube

Modelled from photos and videos using Fusion 360.

Single and Multicolour 1:1000 models on P&O Cruise ship Ventura also available on this site.

Note that I have improved the text on this model when compared to ventura - by insetting the text 0.25mm, rather than it protroding 0.5mm like it does on the Ventura model.

Multi colour versions of these models will probably be released once I have done some test prints - but note that they will take over 24 hours to print and will require a Bambu Lab X1C and 3xAMSs and lots of filament.

This is a personal project. I have no connection to P&O Cruises or Carnival Corporation other than being a customer.

Models hosted exclusively on Makerworld until Dec 2023.

This version is released under a CC Non Commercial No Derivatives license due the P&O Cruises branding.

Comment & Rating (21)

@3Dphillyment

Hi, great looking models. i was on iona in november 2023 and would love to print a single part version like this, scaled down to 50% but multicoloured like the other version mostly at 0.08 to keep as much detail as possible, or wouldn't that be possible. Here's a picture of the model that you can buy from the giftshop onboard the ship.

(Edited)

The designer has replied

@Ukdavewood

Thanks, there is a 1:1000 Iona model in this upload too - but it is split into two halves - that could be lined back up again before slicing. If you are talking about a 1:2000 version of Iona, it is probably possible by simply scaling the model down by 50% and using a 0.2mm nozzle at 0.1mm layer height. Print a 1:2000 version with a 0.4mm nozzle would require a fair bit of rework to the model.

@Ukdavewood

Correction - the Iona Multi colour that would need to be joined is in this download https://makerworld.com/en/models/15006#profileId-14776

@3Dphillyment

Replying to @Ukdavewood :

Thanks for the fast reply but the link sent me to the Arvia single plate multicoloured print and i couldn't see a download for the iona. Ideally i would like to print smaller than a single plate but this sounds like a bad idea so i've decided to do one that would fit on a single plate.

@Gary.Coats

Print Profile

Arvia and Iona 0.2mm layer, 2 walls, 5% infill

printed as a gift in one committee to allow it to be hand painted. detail is amazing and printed superbly for 98%. some post print work to remove stringing inside some of the tiny detailed structures but that’s all. impressive

The designer has replied

@Ukdavewood

Thanks - would be interested to see what it looks like when it is painted.

@3DMosaic

Wow! The ocean liner is amazing! I am looking forward to a color-painted print profile!

The designer has replied

@Ukdavewood

Thanks - have just uploaded the Arvia multi colour version - 28hrs print time and 11 colours needed though - so I would recommend trying one of the single colour versions first:)