A remix of the model https://www.printables.com/es/model/84614-heavy-duty-battery-powered-solder-fume-extractor by user Lewosh. All thanks to him.
All parts have been redesigned to fit the new design.
What's new?
- Added the possibility to use Parkside x20 batteries. It can also be used connected to a 12v dc adapter. By mounting the dc adapter that I attach in the list of required parts, you can use adapters up to 40v. ¡¡¡ Do not use power supply and battery simultaneously!!!.
-The fan housing is now telescopic.
-Base and cover have been redesigned to add the new electronic components. Power cut-off switch has been added.
-Control panel redesigned to add a led switch and battery status monitor.
-Added a led light bracket.
.3mf files now have the proper print profile, such as ideal part position, layer height, fill and manual supports.
Necessary parts:
Electronics:
Battery status monitor x1 (Only if you are printing the battery version)
Switch x2
LED strip
dc-dc converter x1 (This element is not necessary if you are going to use a 12v power supply in the model without battery.)
Wire
Otros:
Flange
Soldering iron
spade male terminal x2 ( Only if you are printing the battery version )
Glue
Multimeter (To adjust the dc-dc converter to 12v)
TUTORIAL
1º Print the models.
2º Once printed make sure that the screw holes and wires are clean.
3º Pass each one of the cables through the hole of the battery connector and solder the terminals to them. Insert the terminals to the bottom and glue them with glue to prevent them from moving.
4º Solder the positive cable of the battery connector to the positive pole of the dc-dc converter.
5º Screw the dc-dc converter to the base with m3x8mm screws.
6º Solder a wire to the negative pole of the dc-dc converter.
7º Now it is time to adjust the output of the dc-dc adapter to 12v using the multimeter.
I attach a diagram and sample images to make the rest of the connections.
Reminder
If you have not set the dc-dc converter to 12v, now is the time to use the multimeter.
If you like my designs give me like and share. If you like them a lot invite me to a coffee.
https://www.buymeacoffee.com/kjbturok
https://www.paypal.com/paypalme/ChinadlaConchinchina
ESPAÑOL
Un remix del modelo https://www.printables.com/es/model/84614-heavy-duty-battery-powered-solder-fume-extractor del usuario Lewosh. Todos los agradecimientos a él.
Se an rediseñado todas las partes para ajustarse al nuevo diseño.
¿Que tiene de nuevo?.
- Se le a añadido la posibilidad de usar baterías de la marca Parkside modelo x20. También puede usarse conectado a un adaptador dc 12v. Montando el adaptador dc que adjunto en la lista de partes necesarias, se pueden usar adaptadores de hasta 40v. ¡¡¡No usar fuente de alimentación y batería simultáneamente !!!.
-La carcasa del ventilador ahora es telescópico.
-Se a rediseñado la base y la tapa para añadir los nuevos componentes electrónicos. Se a añadido un interruptor de corte de energía.
-Panel de control rediseñado para agregar un interruptor para el led y un monitor de estado de batería.
-Se a agregado un soporte para luz led.
Los archivos .3mf ya cuentan con el perfil adecuado de impresión, como la posición ideal de la pieza, la altura de capa, relleno y soportes manuales.
Tienes dos modelos a elegir, con y sin batería. Ambos cuentan con conector DC. Imprime el que creas necesario.
Componentes necesarios:
Electronica:
Monitor de estado de batería x1 (Solo si imprimes la versión con batería)
Conector DC hembra x1
Interruptor x2
Tira led
Convertidor dc-dc x1 (Este elemento no es necesario si vas a hacer uso de una fuente de alimentación de 12v en el modelo sin batería)
Cable
Otros:
Insertos de laton m3 and m4 x4
Bridas
Soldador de estaño
Terminal de pala x2 ( Solo si vas a imprimir la versión con batería )
Pegamento rápido
Multímetro ( Para ajustar el conversor dc-dc a 12v )
TUTORIAL
1º Imprime los modelos.
2º Una vez impresos asegúrate que los orificios de tornillos y cables estén limpios.
3º Pasa cada uno de los cables por el orificio del conector de batería y suelda los terminales a estos. Introduce los terminales hasta el fondo y pégalos con pegamento para evitar que estos se muevan.
4º Suelda el cable positivo del conector de batería al polo positivo del conversor dc-dc.
5º Atornilla el conversor dc-dc a la base con tornillos m3x8mm.
6º Suelda un cable al polo negativo del conversor dc-dc.
7º Ahora es momento de ajustar la salida del adaptador dc-dc a 12v haciendo uso del multímetro.
Te adjunto un diagrama e imágenes de muestra para hacer el resto de conexiones.
Recordatorio.
Si no as ajustado el conversor dc-dc a 12v, ahora es momento haciendo uso del multímetro.
Si te gusta mis diseños dale me gusta y comparte. Si te gustan mucho invítame a un café.
https://www.buymeacoffee.com/kjbturok