HygroMeter Stand for BambuLab X1

HygroMeter Stand for BambuLab X1

Boost
267
434
168

Print Profile(4)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
30 min
1 plate
4.8(105)

Paned 15° version  0.2mm layer, 2 walls, 15% infill
Paned 15° version 0.2mm layer, 2 walls, 15% infill
33 min
1 plate
4.7(24)

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
30 min
1 plate
5.0(5)

A1-0.2mm layer, 2 walls, 15% infill
A1-0.2mm layer, 2 walls, 15% infill
28 min
1 plate
5.0(3)

Boost
267
434
168
0
834
608
Released

Description

Modeled in Fusion 360, face down, no need support.
It has two “buttons” that will fit the left 2 holes at the back, so it stays in place.
Angled up a little so you can look in from the top glass.

The last firmware update allows you to use your X1 as the most expensive filament dryer lol
this could be useful :)

attached are the step file if you want to tinker with it, and the BambuStudio 3MF

The Hygrometer link from amazon:

Update 10/8/2023 : I added a version (STEP File) that panned 15 degrees left
Red Original, Green alternate version

Comment & Rating (168)

Please fill in your opinion
(0/5000)

The print and fit were perfect, but the location did not work for me. Unless you have additional lighting, the numbers are not visible on the camera.
The designer has replied
1
Reply
well yeah… the built-in led is just too weak to reach…. if you look on the raw model… I uploaded an alternative that pans 15 degrees left… more visible… but still need better lighting than the original led, check out my DK Riser Low Profile.. easy to print too
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Easy to print and fits well ín my P1P.
2
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
It prints well and everything fits together nicely, but it’s hidden by the extruder at rest.
2
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
printed well. I woukd prefer to have more control on the Handy app to modify the printing profile of the object selected for printing, but it printed well!
2
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Easy to print and fits well. Thanks!
2
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
excellent model and printed very well
2
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Printed perfectly and fit the hygrometer I have. Thanks for making it.
2
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Prints well, doesn't get in the way of the toolhead. I used black ABS. I was able to see the values on the P1S camera if the room is not dark.
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Very useful print if you have a new printer and are working on beefing up the customizations. This is no fault of the print but the hygrometer might be hard to read so be prepared to beef up the internal lighting in your printer.
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Passt Perfekt. Super. Danke
1
Reply