Print-In-Place Motorhome RV

Copyright Claim

Print-In-Place Motorhome RV

Boost
370
598
145

Print Profile(2)

All
P1P
P1S
X1
X1 Carbon
X1E
A1
A1 mini

0.2mm layer, 2 walls, 8% infill
0.2mm layer, 2 walls, 8% infill
Designer
2.5 h
1 plate
4.9(91)

Faster print, 0.28mm layer, 2 walls, 15% infill
Faster print, 0.28mm layer, 2 walls, 15% infill
2.1 h
1 plate
5.0(11)

Open in Bambu Studio
Boost
370
598
145
66
1 k
734
Released

Description

Join my Patreon for dozens more models like this! Commercial license included!

 

This model is fully print-in-place and does not require assembly. This is a great model to test your clearances, bed adhesion, and overhangs. The clearances are 0.3 mms on both models. If you'd like to see more of my designs, check my profile or click the Etsy link below for my paid models!

Please post your makes, I love seeing them!

 

If you would like to support me, consider these options:

 

Social Links:

Comment & Rating (145)

Please fill in your opinion
(0/5000)

The print profile is no longer public
Once it got done. I had to dam near break it to get the pop out to slide. Destroyed it enough trying to get it out. Don't even want it now as the slide out is ruined. Tried using a knife to clear anything in the cracks. STUPID. Wasted time and filament.
The designer has replied
0
Reply
if plate hadn't fully cooled, it will stick to plate and deform the model trying to pry it from plate, causing the door to deform slightly and jam. perhaps your filament wasn't dry and it clumped at a spot internally around the door causing door to jam, or some other user error. you can see from other reviews, it prints fine.
1
Reply
Definitely was not user error. I am tech savy. Bed was clean. Filament was dry and not subject to extreme temperatures so there was no moisture in the roll. Also, this comment was posted elsewhere. So, not just user error when its a common problem.
0
Reply
Replying to @DigiPrint :
Just read through comments. Just so happen. The comment that said the same thing as mine. Is now gone...
0
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
looks great love the pop out was a little hard to get the pop out though
1
Reply
Boosted
how did you get yours to come out. can’t get it on mine
0
Reply
Replying to @Red33 :
i used a blade and stuck it in then wiggled it around and it came out. i use the Bambu scraper blade
0
Reply
Boosted
Replying to @mdistel :
Thank you, got it out finally
0
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
Another great model from this talented designer. Will look good in my motorhome! My only suggestion would be to redesign windows on the print bed side to avoid bridging. If they can be printed flat on the first layer they would look nice like the windows on the top side.
3
Reply
Anyone know why the wide extension won’t come out but the awning will? It may be from the infill but does anyone have any ideas of how to make it come out?
The designer has replied
0
Reply
Try pushing it inward instead to try and free it up. Then see if it can slide out.
0
Reply
Replying to @WhopperPrinting :
I tried but didn’t work may try to print another 😔
0
Reply
The print profile is no longer public
Love it!
1
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
très très beau rendu
1
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
Really a cool print. Thank you for sharing. Any advise on how to get the tipout loose without breaking it?
1
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
I forgot to get a picture of the finished print. Turned out great, love the movable parts!
1
Reply
Everything is superb
Show original
0
Reply
It’s quite good.
0
Reply