Poop Deflector (A1 + A1 Mini) by ThreeD-Michael

ThreeD-Michael

3D Printer>3D Printer Accessories

Print Profile(7)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

Poop Deflector

Designer

17 min

1 plate

4.9(961)

Ironing + 0.1mm layer, 3 walls etc.

32 min

1 plate

5.0(96)

PETG ~ 24mins ~ 4g ~ 0.2mm layer, 2 walls, 15% infill

25 min

1 plate

5.0(25)

Added Bambu Logo

22 min

1 plate

4.4(7)

Click to see more

Open in Bambu Studio

Boost

1074

2045

1238

256

6 k

5.8 k

Released

Description

Poop Deflector for Bambulab A1 and A1 Mini

I know there are already poop deflector designs online. I tried a few but didn't like them because they were either too brittle and/or lacked a proper attachment. That's why I created my own design, which offers the following advantages:

secure fixation,
stabilized deflector,
stable walls,
easy and quick printing,
only 4g weight.

Since I've been using this deflector, no poop has missed the basket...

Assembly:

Carefully click the poop deflector onto the purge wiper. Place a collecting container under the deflector and make sure that the deflector cannot touch the container in the lowest z position of the printer.

Comment & Rating (1238)

@hardermods

noticed some pla is still hot and sticks to it, added a piece of aluminum tape to prevent that. works great

@lil_nut

good idea. thank you!

@johnbcs

Boosted

An excellent design, nicely done! It printed beautifully in Bambu PLA Basic. I added some kapton tape to prevent sticking. edit: I switched the kapton tape to aluminum tape.

(Edited)

The designer has replied

@ThreeDMichael

In the early years of 3D printing, Kapton tape was glued to the print bed to increase adhesion. That's why I would have some doubts as to whether it's the right material for the poop deflector. I use the deflector on one printer without stickers and on a second one with self-adhesive aluminum foil. But since poops don't stick to either of them, I can't make a recommendation here.

@smashd

Boosted

Replying to @ThreeDMichael :

what about Teflon / PTFE Tape, I use that as a cheap alternative to dedicated mouse feet, works great and should prevent sticking quite nicely - note to self: I have to try that

@johnbcs

Boosted

Replying to @ThreeDMichael :

I see, I didn't know that. I haven't had any issues with any of the flung poops sticking to it but I'll probably switch to something else.

@sergiopenya

Print Profile

Poop Deflector

I printed it with the filament that comes free with the printer and I ran out, but it works perfectly. I would rate it 5/5!!

Other Issues:Ran out of filament!

@Droid_Junkie

Why would you rate it a 3 when running out of filament is your fault? That's not fair to the creator......

(Edited)

@sergiopenya

Replying to @Droid_Junkie :

Makerworld doesn't let me rate it 5 starts, that's why I put in the final that I would rate it 5/5.

@smashd

Boosted

Print Profile

PETG ~ 24mins ~ 4g ~ 0.2mm layer, 2 walls, 15% infill

broke it off during the A1 heatbed replacement so I've printed it again in PETG (PLA poop does stick a lot less to that)

The designer has replied

@TheGooser

Boosted

thanks!

@smashd

Boosted

Replying to @TheGooser :

I have to thank you! :) it's a great design!

@RelicWarrior

Print Profile

PETG ~ 24mins ~ 4g ~ 0.2mm layer, 2 walls, 15% infill

came out great!

The designer has replied

@TheGooser

Boosted

thanks!

@Toast

Print Profile

PETG ~ 24mins ~ 4g ~ 0.2mm layer, 2 walls, 15% infill

Printed well on Elegoo Rapid PETG

The designer has replied

@TheGooser

Boosted

thanks!

@Rom_Ka

Print Profile

PETG ~ 24mins ~ 4g ~ 0.2mm layer, 2 walls, 15% infill

passt

The designer has replied

@TheGooser

Boosted

thanks!

@brianneathery

Print Profile

PETG ~ 24mins ~ 4g ~ 0.2mm layer, 2 walls, 15% infill

Keeps the little guy from flinging his poo across the room.

The designer has replied

@TheGooser

Boosted

gotta keep the poo in its place! thanks!

@Kryzbar

Print Profile

PETG ~ 24mins ~ 4g ~ 0.2mm layer, 2 walls, 15% infill

fit nice

The designer has replied

@TheGooser

Boosted

thanks!

@nodirektion

Print Profile

PETG ~ 24mins ~ 4g ~ 0.2mm layer, 2 walls, 15% infill

Printed for my 2 A1 Mini - Fits Perfect!! Thx :)

The designer has replied

@TheGooser

Boosted

thanks!

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.