AMS Lite Numbers by Wojciech Kawa

Wojciech Kawa

3D Printer>3D Printer Parts

Print Profile(11)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

Bowden Protect, 0.2mm layer, 2 walls, 15% infill

Designer

46 min

1 plate

5.0(500)

0.2mm layer, 2 walls, 15% infill, Arachne

Designer

36 min

1 plate

4.9(464)

Upside Down Version, 0.2mm layer, 2 walls, 15% infill

Designer

36 min

1 plate

4.9(192)

Bowden Protect - Upside-Down, 0.2mm layer, 2 walls

Designer

48 min

1 plate

4.9(295)

Click to see more

Open in Bambu Studio

Boost

1352

2629

1645

747

5.5 k

5.2 k

Released

Description

My AMS overlay design with slot numbers.
I used gray and white to make the numbers as visible as possible, but you can of course use any color combination.

I designed a version for users who mount their AMS lite on top of an A1 printer (AMS lite Top Mount for A1). link in the image.

Boost Me (for free)

If you appreciate my work please give me a Boost.

Update !

I noticed that some users wanted to protect their Bowden tubes from the excessive wear and tear of tugging, and I thought it might make sense, so I added Bowden tube holders to my earlier design.

The standard version and the version with Bowden tube protection have upside-down versions for people who mount the AMS on the wall or on dedicated stands.

Check the flow ratio before printing. My print has a few flaws, but they are visible only in photos, normally they are almost invisible.

Updated May 9, 2024

I replaced the source files from stl to step, which makes the model walls smoother.
Due to the information from the comments that the model is too tight in some cases, I increased the length by 0.5 mm, which should solve the problem. (the width is the same so I shouldn't be too loose)
Attention! Models with increased length are only in my print profiles!

Comment & Rating (1645)

@RobinDiekmann

Print Profile

0.2mm layer, 2 walls, 15% infill, Arachne

Awesome, just great! Printed on a carbon bed with black and green PLA, looks really good. The fit is absolutely perfect.

@user_1658220205

love the CF look!

@RobinDiekmann

Replying to @user_1658220205 :

Yeah it really makes it pop!

@lmc590

that looks nice, I have that plate but I keep experiencing adgeation problem after a couple of prints, no amount of soap or IPA has helped, have you experienced anything like that, any tips. thanks.

@EngravePrinting

really liked this, but is there any modifications in the pipeline to allow for the (Bambu) AMS on top mod? That has the filament guides, which fit within the original numbers.

@pjgdiver

I second this option as well. Trying to do it myself, but I am not good at 3D modeling

@luftpump

Can anyone send me a printable file for this 4 numbers ? This is a great solution for me.

@user_143056145

Great upgrade. Went 3 colors to better see from a distance or from my camera. The fit was just a little tight to the point it was pulling the AMS covers open. I tried sanding the inside to fit but ended up grabbing the heat gun. Warmed the middle of the part just a little and slapped them on. Perfect fit!!

The designer has replied

@WojciechKawa

For me it fits perfectly. I didn't know it could be so tight. The only solution I can think of is to print again, increasing the scale a bit, for example 100.5%.

@Gigagamesguy

Replying to @WojciechKawa :

habe das gleiche Problem, druck war sauber und sehr sauber, ich denke das es nach dem kalt werden sich etwas zusammenzieht, werde das auch mit dem Heißluftfön probieren. Auf der Originale Bampu Platte konnte ich drucken auf der Von Ali mit Struktur ( Habe im Studio auf smooth PEI gestellt) ging es nicht.

@Norkius

Replying to @Gigagamesguy :

Try 55°C for these smooth plates

Show original

@user_86844756

Boosted

Could you please design one like this?

The designer has replied

Show original

@WojciechKawa

Yes, I will send it to you in a private message.

@user_86844756

Boosted

Absolutely perfect Thank you

Show original

@matataa

Boosted

Replying to @WojciechKawa :

I'm looking for the same version. Can you send it to me as well? Thank you!

@NAIAD3D

Print Profile

0.2mm layer, 2 walls, 15% infill, Arachne

Great design, fits perfect

@craigtbii

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill, Arachne

Works well. Too bad ams can't handle glow in the dark because this would be a perfect use case.

(Edited)

@filamentalpw

Uh oh. 😅

@JamesKpa

I print glow in the dark pla in ams lite with no problem

@AKA_Ordeep

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill, Arachne

Print very well

@Trimmz4D

what’s that around your ams?

@AKA_Ordeep

Boosted

Replying to @Trimmz4D :

It’s a closure https://makerworld.com/models/486153

@KRONK

Boosted

Hi, Is there a version with the PTFE tube holder with the numbers reversed? I have switched the cables on the motherboard and that sums it up that my numbers are in a 4-3-2-1 order but mounted upside down so it becomes 1-2-3-4.

(Edited)

The designer has replied

@WojciechKawa

Hello, I haven't made such a modification yet, but give me a moment and I will send you a modified version just as you need.

@KRONK

Boosted

Replying to @WojciechKawa :

oh, that's very nice of you! =)

@user_1656279385

Print Profile

0.2mm layer, 2 walls, 15% infill, Arachne

Very cool caps, which I immediately printed and installed. They were also wonderful in the horizontal holder: https://makerworld.com/en/models/92486#profileId-100105 Now there is a vertical version https://makerworld.com/en/models/653654#profileId-580497 Unfortunately, the numbers are upside down in that one. Can it be reversed? That would be great, then I would reprint it immediately. The bracket cannot be rotated. THIS IS NOT CRITICISM, JUST A SUGGESTION! Thank you

The designer has replied

Show original

@WojciechKawa

Profile named: "Upside Down Version, 0.2mm layer, 2 walls, 15% infill" is what you need. I designed all possible variants, side sides are in a separate project.

@user_1656279385

Replying to @WojciechKawa :

Many tnx, just downloeded them. Will print tomorrow.

@foodiefriends

Print Profile

Bowden Protect - Upside-Down, 0.2mm layer, 2 walls

these are super cute but they tend to pop off when the mini is in motion. maybe if I printed the ones without the tube slot I wouldn't have this problem. it's still a really great model and I definitely recommend it!