AMS Spool Cover v2
Copyright Claim
AMS Spool Cover v2
Boost
343
738
253
Print Profile(4)
DURABLE | 0.2mm layer, 5 walls, 100% infill
Designer
26 min
1 plate
OPTIMIZED | 0.2mm layer, 3 walls, 100% infill
Designer
26 min
1 plate
Recommended | 0.2mm layer, 3 walls
Designer
26 min
1 plate
Rapid PETG - Durable
26 min
1 plate
Boost
343
738
253
14
1.4 k
2.9 k
Released
Description
Description
In order to solve the annoying problems with cardboard spool filaments, here it is the final version of the spool ring, that solved all my problems of spools getting stuck into the AMS.
Compatibility
Tested to work with the cardboard spools from the following filament brands:
- 3DE Premium
- 3DQF
- Anycubic
- Canadian Filaments
- Comgrow
- Creality
- Duramic
- Elegoo
- eSun
- ERYONE (Need to scale: X: 199.80 (98.91%) Y: 199.80 (98.92%) Z: 5.5 (100%))
- Filamentive
- Filaments.ca
- Flashforge
- FIXDRY
- GNVTNTP
- Inland
- Jayo
- Kexcelled
- KYUUBI
- Matter3D
- OtterTek
- Overture
- OVV3D
- Polymaker (e.g. PolyTerra / PolyLite)
- Print Bed
- real Filament
- Redline
- Reflow
- Smartfil
- Sparta3D
- X3D
- Ziro
- (Jessie filament spools are too wide for the AMS)
If you find this works with a brand of filament with cardboard spools that's not listed here, please leave a make or a comment and I will add it to the list!
Comment & Rating (253)
All
sadly does not work with AMS cover closed.
The designer has replied
4
Reply
What spool are you using?
0
Reply
That has always been my experience with these rings. AMS lid will not close and latch; so it's a deal breaker for me.
0
Reply
This is true for me and using this with Creality Hyper PLA (cardboard spool). To solve this while printing; you know those two latches that secure the AMS lid? I put the latches under the lid instead of using them to lock the lid. This keeps the lid open just a tiny bit, and enough where the ring doesn't scrape the lid when it turns.
(Edited)3
Reply
Print Profile
DURABLE | 0.2mm layer, 5 walls, 100% infill
Perfect for polyterra spoon, little bit bigger for ERYONE. need to resize it. by the way, perfect print!
The designer has replied
2
Reply
What was the right % in order to resize it for ERYONE?
0
Reply
Replying to @Hanti_3d
Here the eryone' size:
X: 199.80 (98.91%)
Y: 199.80 (98.92%)
Z: 5.5 (100%)
Hope this can help!
(Edited)4
Reply
Replying to @EFFEG
Thanks!
0
Reply
Print Profile
Recommended | 0.2mm layer, 3 walls
This is a great idea, I love functional prints. The model printed really well for me but unfortunately I damaged it getting it off the build plate.
1
Reply
I did the same thing with my second set of prints, so the 3rd one, it was so frustrating. I also changed the wall number to 5 and the infill to 100% for much better results but didn't think to post them. The prints were quite difficult to remove from the plate due to their rigidity, I was afraid I would snap them in half or crack them again.
0
Reply
ERYONE Scaling needs to be set to 98,91 for perfect fit
JAYO (neat winding pro) it even needs to be smaller haven't tested exact size
The designer has replied
1
Reply
Thanks you sharing your experience
0
Reply
not fitting jayo neat winding pro 1.1kg PETG cardspool
(Edited)
The designer has replied
0
Reply
Hi! please measure your spool and scale X and Y for a perfect fit
0
Reply
Replying to @Hanti_3d
Hi, the scale for jayo spools is:
- X 198mm
- Y 198mm
- Z 5,5mm
Please try this settings.
(Edited)0
Reply
Print Profile
Recommended | 0.2mm layer, 3 walls
Fit my elegoo cardboard container perfectly! Hopefully I can now use this roll in my AMS without issues.
1
Reply
Print Profile
OPTIMIZED | 0.2mm layer, 3 walls, 100% infill
Worked fantasic for Polymaker PLA
1
Reply
Print Profile
Recommended | 0.2mm layer, 3 walls
Printed fine, was a little tricky to get off the bed after. It's a tiny bit too small for the 3DPO spools. (I think it's the exact same size as the cardboard spool). I managed to get it on with some force and stretching however then I couldn't close the AMS lid. I think if the cardboard spool alone only just fits in the AMS without the covers. If the cardboard was a tiny bit smaller it would have fit both on the spool and in the AMS
0
Reply
Print Profile
DURABLE | 0.2mm layer, 5 walls, 100% infill
Perfect, fits all my rolls and helps with the cardboard rolls that are almost out of filament.
0
Reply
Print Profile
OPTIMIZED | 0.2mm layer, 3 walls, 100% infill
I used the "optimized" profile and got good results.
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike
© 2024 MakerWorld