Case ESP8266 WeMos D1 mini USB C, w reset button by Valeria Momo

Valeria Momo

Hobby & DIY>Electronics

GIF

Print Profile(3)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

Version A 0.16mm layer, 2 walls, 15% infill

Designer

24 min

1 plate

4.7(10)

Version B 0.16mm layer, 2 walls, 15% infill

Designer

41 min

1 plate

5.0(3)

0.2mm layer, 2 walls, 15% infill

21 min

1 plate

4.5(2)

Open in Bambu Studio

Boost

125

117

Released

Description

Case for Esp8266 Wemos D1 mini USB C with reset button, very easy to print.

Please note that when you buy this item it may arrive with slightly different dimensions because the cutting process is not very precise. I myself have had Esp8266 with a different width of about half a millimeter, or where the USB-C connector was in a slightly offset position. For this reason I created 2 different print profiles. Before printing many I advise you to see what is right for you.

No support needed. ESP.

Comment & Rating (28)

@WhiteHatHacker

Print Profile

Version A 0.16mm layer, 2 walls, 15% infill

Nice little case. Fit is very good on the board. Only issue is the button is a tight tight fit and the issue arises when it is so tight that the boot button on the side is not strong enough to push the button back through the hole and will stay in a depressed state.

The designer has replied

@ValeriaMomo

I am very sorry! it could be a problem with an imperfect print (tolerance or dirty print) or your esp has slightly different measurements on the button

@WhiteHatHacker

Replying to @ValeriaMomo :

It still did the job! Nice print!

@WhiteHatHacker

Replying to @ValeriaMomo :

Its no big deal the case iteself is still great and I still use it to house my 8266 today.

@user_2399735769

Thank you for this beautiful case, which is perfect for its purpose. The RST button also fits nicely and works without any friction. Perhaps it would be a good idea to consider the USB connector opening as many connectors on the market may not fit as they are too large.

The designer has replied

@ValeriaMomo

thank you, good idea ☺️

@Spas72

Print Profile

Version A 0.16mm layer, 2 walls, 15% infill

Nice litle box.

The designer has replied

@ValeriaMomo

I'm happy that you are satisfied, thank you! I'll take a look at your models :-)

@user_4048091486

Great Case! It also works for my Micro-USB Board. My ESP8266 D1 Mini is ~26mm x ~34mm in size and it fits just right.

@Rene1977

Print Profile

Version A 0.16mm layer, 2 walls, 15% infill

Passt perfekt.

@Mattia3D

Very useful thank you

@dwinter.wd

Print Profile

Version A 0.16mm layer, 2 walls, 15% infill

es ist später sehr schwer den D1 Mini wieder heraus zu bekommen sonst ein sehr kleiner Bauraum

@Thepitbull21

Print Profile

0.2mm layer, 2 walls, 15% infill

Ottimo

@Vigo3D

Print Profile

Version A 0.16mm layer, 2 walls, 15% infill

Good model

@Treenity

Print Profile

Version B 0.16mm layer, 2 walls, 15% infill

The designer has replied

@ValeriaMomo

thank you :)

@Treenity

Replying to @ValeriaMomo :

do you think you can release another version with higher box ? for shields / components etc… if you can’t I will try to make a remix when I have some time.