zuperbuuworks

<h4>IMPORTANT! PLEASE READ THE DESCRIPTION BEFORE PRINTING. SUPPORTS ARE REQUIRED.</h4><h4>This model has only been test printed on an X1C, on a cool plate, using PLA filament. Expect different results if using a different type of machine, or materials.</h4>This model is based on the Warden from Minecraft; it has simple ball-jointing on the arms, legs, and head. There is a full-colour version, which I have tried to optimise the flush volumes of to reduce waste, but it is still a filament-eater. I have provided a flat colour option too, if you'd rather paint him yourself. Supports are needed. A brim is also recommended due to the nature of the support layout. If you'd rather not use supports on the main body, simply lower the body into the plate before printing. Doing this tells the slicer to remove the back ribs/spine, and any supports that were needed before will be removed. Supports are needed on the arms to help the socket-joint to print properly. If you wish to sell prints, or get access to the RAW STLs, please consider joining my Patreon: https://www.patreon.com/thomastedwards

Minecraft Warden Toy

Other

This Stylized Crab doesn't want you to cook him; he just likes to hide in the pot! Please do not use the pot for actual cooking. The crab has 22 points of articulation, including a new “swivel” joint I had not tried before on the arms. The legs are floppy so he can rest over bumps and other surfaces. He is best printed using the Bambu Lab “Pla Basic gradient - Solar Breeze” filament. The pot uses “PLA Metal - iron grey” and “PLA Basic - bronze”. Supports are not needed on the crab or pot base. Even if the slicer says it is recommended to use them, I printed mine without them. I also did not use a brim, and would recommend just using a freshly cleaned/glued hotbed with no brims. The pot lid may print better with supports, but I didn't use any for mine. See the range of motion in the video.<figure class="media"><div data-oembed-url="https://youtu.be/25uBOZZrq4Q"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/25uBOZZrq4Q" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>This file covers PERSONAL use. If you want to sell prints of this model, please subscribe to my Patreon: <a target="_blank" href="https://www.patreon.com/thomastedwards" rel="nofollow noopener">https://www.patreon.com/thomastedwards</a> You also get additional benefits when subscribed, like access to Patreon exclusive models, such as the more realistic crab!

Cute Articulated Crab & Decorative Cooking Pot

Animals

If you sell prints of these models, you must be subscribed to my Patreon to maintain a license: <a target="_blank" href="https://www.patreon.com/thomastedwards" rel="nofollow noopener">https://www.patreon.com/thomastedwards</a>&nbsp;This little keyring is based on my larger <a target="_blank" href="https://makerworld.com/en/models/81150#profileId-86320" rel="nofollow noopener">Articulated Kohaku River Spirit</a> model. It has some articulation, but the legs do not move. I would not print it any smaller than the provided file. I also would not use it on items that go in a pocket or a bag. It's best used on the outside of a bag. Due to the limit of 4 colours, the pupils are not black. A dab of acrylic or permanent marker works fine.&nbsp;If you'd rather not have it as a keyring, simply delete the negative cylinder part as shown in the picture, and you're good to go! (both Kohaku and Shenron have the hole in the same place) <img src="https://makerworld.bblmw.com/makerworld/draft/281644/2023-12-13_806d85f3e7c78.jpg"> I printed mine without a brim; providing your hotbed is clean/freshly glued, you shouldn't need a brim either. Supports are not needed for this model; do not use them or the model can break when you remove it from the supports!

Articulated Little Kohaku Keyring

Dragons

This is a remix of my Price Stand; this version lets you hang the prices on metal mesh racks. I would not recommend using them on string or other fabric-based lines. 3 versions support for 3 characters, 4 characters, and 5 characters. The cards from the original file fit these hangers. I have included some new cards with this file that can label your items as “each” or “for #number”. If you modified the original card sizes, you'll have to modify the sizes of these hangers. If the cards are too loose, scale the model down slightly. If the cards are too tight, the model needs scaling up.<h3>If you want the numbers and currencies (Euro, Dollar, Riyal, Afghani, Yen, Won, Rupee, and Pound) they are included in the original Card Stand file. Only the hanging stand is in this print profile!</h3>You can use these printed hangers to really make your products stand out at your local garage sale, or convention stall, as they use bold typography to make them easy to read!&nbsp;Please do not sell prints of the price stands though unless you are subscribed to my Patreon: https://www.patreon.com/thomastedwards

Other

Animals

Dragons

Functional