yurisminator_rc

Tom Vít

The brand new McLaren MP4/4, piloted by the famous Ayrton Senna, is very good except for one crucial detail: the ratio of front to rear tyres does not match reality at all and can distract a bit. Yet all you have to do is print the tyres again and change the set slightly.&nbsp;A few important tips:<ul><li>OK, the tyres are not a 1:1 original, but close enough for me and printable. </li><li>You have to a adjust the floor of the formula a bit and use a shorter rear axles. For more details see this great and practical <a target="_blank" href="https://www.youtube.com/watch?v=9SEB9UjmZcc" rel="nofollow noopener">video from RacingBrick on YouTube</a>. (No, my tires are different from the video, designed from scratch.)</li><li>Yes, it can be nice to have these tyres flexible, but is much easier to print them from PLA/ABS/ASA with white or yellow letters on top. </li><li>Use Arachne perimeter generator for better details on top.</li><li>Do NOT use Aligned Seam in your print profile, use Random position choice instead. The points around the tire match the collected dirt from the track better than an aligned and very distracting seam.</li><li>You can use Axle_tolerance_test_piece to determine the axle tolerances (possibly tune up your print profile). However, desktop FFF printing is not completely accurate or repeatable.</li></ul>I am also making this model available for printing for personal use free of charge.  You can support my work for community with 2 €/$ for a good cup of tea if you want via <a target="_blank" href="https://www.paypal.me/tvit" rel="nofollow noopener">paypal.me/tvit</a>.&nbsp;Hopefully, I won't see scammers again who will print models for money without permission /license and profit from other people's work. It's really frustrating, over and over again. I don't even feel like sharing some of the models anymore. But let's stay positive.&nbsp;Edits:<ul><li>240317 … Due to the demand I prepared and added both models (front and rear wheel)  also without logos.</li></ul>

Realistic wheels for 10330 McLaren Senna Formula 1

lego

Exotech

<h2>FOG LIGHT FRAME/ NEBELSCHEINWERFER FOR BMW E30 320IS</h2>

BMW E30 FOG LIGHT FRAME FOR 320IS 

rolf

Lisa Lisa Made

Organize your morning and evening pills in this aptly pill shaped organizer. There are two compartments per “pill” for each day of the week. The lids have a sun and a moon in addition to the day of the week to assist in organization. The main body is printed all as one piece, and then there are seven individual lids that snap into place and can be slid to reveal either the morning or evening compartment.&nbsp;*Bonus* Single unit has been added with two lid options - blank or sun & moon (no day of the week text) !&nbsp;Design Features:<ul><li>Easily customizable - because the lids are loose, you can choose which day to start your week with (the 3DM model has the lids grouped into their own assembly separate from the main body for easily making the lids a different color from the main body)</li><li>No additional parts needed - the lids are designed with a friction fit to snap into place and do not require any magnets to stay closed</li><li>Single plate print - all lids and the main body fit onto one plate, even when printing in two colors by object (~4 hour print in PLA)</li><li>No printing support required - all parts were optimized to not require any support while printing on the X1 Carbon (134g total)</li></ul>Size & Capacity:<ul><li>243.5mm long x 70mm wide x 23mm tall (~9.58" x 2.75" x 0.9")</li><li>I can easily fit 7 pills of varying sizes in one half compartment, or 4-6 if just filling it with medium/larger pills (if folks are interested I can easily maker a taller version that could hold more pills)</li></ul>Print Setting Variations (for PLA on an X1 Carbon):<ul><li>Standard 0.2mm layer height with the 0.4mm nozzle on PEI textured plate</li><li>Switched to “adaptive cubic” infill while in “global” settings</li><li>Selected “print by object” while in “global” settings</li><li>Customized variable layer height settings separately for body and lids to get enough detail in chamfered mechanical areas without increasing entire print time significantly by using a fine layer height for entire print</li></ul>Assembly & Use:<ul><li>Sliding dovetailed lids will require a little force to “snap” into place the first time (lids should slide smoother after a few rounds of opening and closing to break the mechanism in)</li><li>There are protruding chamfered areas on the underside of the lid that keep it from just sliding open whenever - this means there is some small resistance to slide the lid into the “open” position</li><li>A stopper is located on the center bottom of the lid to keep the lid from sliding too far open - thus, only one side of each day is open at any given time</li><li>Please keep in mind that there is no “child lock” on this design and it is not meant to keep medications secure - for personal use at your own discretion!</li></ul>

Pill Pill Organizer - 7 Days - Morning & Night Compartments

line

Mici

Based on DUMMY 13 Beta - Oct. 2023 <figure class="table"><table><tbody><tr><td><a target="_blank" href="https://www.printables.com/model/593185-dummy-13-printable-jointed-figure-beta-files" rel="nofollow noopener">DUMMY 13 Printable Jointed Figure </a>© 2023 by <a target="_blank" href="https://www.lucky13toys.com/" rel="nofollow noopener">Lucky 13 Toys </a>is licensed under <a target="_blank" href="http://creativecommons.org/licenses/by/4.0/?ref=chooser-v1" rel="nofollow noopener">CC BY 4.0</a></td></tr></tbody></table></figure><ul><li>Used the armor to design a new armor</li></ul>You will find more of such stuff in my collections:<a target="_blank" href="https://makerworld.com/en/u/2185604356/collections" rel="nofollow noopener">https://makerworld.com/en/u/2185604356/collections</a><h2>Description</h2>DUMMY 13 loves COMIC CON!So I have started to design a whole series of characters and costumes for DUMMY 13. This is the first costume from the series &#34;DUMMY13 goes to COMIC CON&#34;.The aim is to preserve the charm and simplicity of Dummy 13.Have fun!&nbsp;Now to the content of BatDUMM, sorry Batman:<ul><li>Batman Masks to use with the original head</li><li>Holster with a Batclaw</li><li>Holster with a Baterang</li><li>Armor with inserted Batman logo</li><li>Use the official parts for any other part</li></ul>Printing:<figure class="table" style="width:100%;"><table><tbody><tr><td> </td><td>Layer height</td><td>Brim</td><td>Supports</td></tr><tr><td>Armor</td><td>0.15mm</td><td>x?</td><td>-</td></tr><tr><td>Logo</td><td>0.10mm / Best with 0.25mm nozzle @ 0.05mm</td><td>x</td><td>-</td></tr><tr><td>Holsters</td><td>0.15mm/0.10mm, your chioce</td><td>-</td><td>x?</td></tr></tbody></table></figure>&nbsp;Assembly:<figure class="table"><table><tbody><tr><td>Holsters:<ul><li>Remove the support after printing (green part in the picture)</li><li>If you need additional supports because of the bridging, be careful as the parts may break when you remove them</li><li>Holsters are simply attached to the leg</li><li>The holsters are fragile. Apply them carefully!</li></ul></td><td style="width:25%;"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000174763/design/b2b9eab8-9051-4873-a2cc-f10c351af0b2.webp"></figure></td></tr><tr><td>Slide the head into the mask and press it in with gentle force on the chin.If this is not possible, it is probably due to the following points:<ul><li>Check the inside of the helmet (the top) to see if it has been printed cleanly and remove any filament debris that is sticking out</li><li>Has the brim been removed cleanly?</li><li>The elephant foot can cause the inner rim to be a little too narrow, just sand the inner rim down a little or work it with a knife</li></ul></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000174763/design/bb3186ae-9d9d-4b13-ac87-d6666e84bd8b.webp"></figure></td></tr><tr><td>Logo:The logo can be snapped onto the armor</td><td> </td></tr></tbody></table></figure>

DUMMY 13 goes to COMIC CON - Batman V2.0 WIP

dummy13

Deviian

The new version is here: <a target="_blank" href="https://makerworld.com/en/models/110283#profileId-117868" rel="nofollow noopener">https://makerworld.com/en/models/110283#profileId-117868</a>&nbsp;A simple model for securing the printer head cable in a vertical position. Printed using standard settings with PLA.

A1_Cable securing for the tool head

Wing-Art

Arachnophobia?&nbsp;Spider-Catcher is a must-have for anyone uncomfortable with creepy crawlies, as it effectively captures them from floors, walls, or ceilings, allowing for quick and safe release outdoors.An extension option (for unlimited size) is also available - because size does matter. ;) I recommend printing the pyramid part in transparent PETG, of course you can print it in PLA, too. Usage:Place the Spider-Catch model over the spider and slide the flap on the underside to safely capture the spider.Transport the spider to a desired location and release it there by simply rotating the rod, which opens the flap, allowing for touch-free release. Just show me your Spider Catcher, I would be very happy to see it!___&nbsp;Spinnenangst? Spider-Catcher ist ein Muss für jeden, der sich bei Krabbeltieren unwohl fühlt, da es sie effektiv von Böden, Wänden oder Decken einfängt und eine schnelle und sichere Freisetzung im Freien ermöglicht.Eine Erweiterungsoption (für unbegrenzte Größe) ist ebenfalls verfügbar - denn Größe ist wichtig. ;) Ich empfehle, den Pyramiden Teil in transparentem PETG zu drucken, aber es geht natürlich auch in PLA.&nbsp;Anwendung:Platziere den Spider-Catcher über der Spinne und schiebe die Klappe auf der Unterseite zu, um die Spinne sicher einzufangen.Transportiere die Spinne an einen gewünschten Ort und setze sie dort durch eine einfache Drehbewegung der Stange, welche die Klappe öffnet, berührungslos frei. Zeigt mir eure Spider Catcher, würde mich sehr darüber freuen!

Spider Catcher - Insect Trap Stick

smart stuff

Aarin Khadpe

This is phone/tablet stand that is made to look like the Bambu Lab A1 3D printer. No AMS is needed to print this model because all of the different colors in the model are separated and can be printed with different colored filaments. Some of the parts need to be glued on with super glue or 5 Minute epoxy.&nbsp;Printing:&nbsp;Print each raw model file once to get all the parts or follow the print profiles. If you want to change colors for the Bambu logo on the build plate, put a pause at layer 4 in Bambu Studio and change the filament at the pause. The pause in included in the print profile&nbsp;&nbsp;Assembly:<ol><li>Press fit the X Axis to the main body. No glue is needed.</li><li>Glue the build plate on to the main body.</li><li>Glue the top grey pieces to the top of the main body.</li><li>Glue the bottom grey pieces to the bottom of the main body.</li></ol>

A1 Phone Stand NO AMS

cute office stuff

dohara1985

Thank you to everyone who has boosted this model. You guys make me feel apreciated and I love it.&nbsp;&nbsp;Spool adapter for spools with a larger hole (Sunlu, etc) than the AMS Lite spool holder.&nbsp;I tried many adapters, most of which I didn&#39;t like. I needed one for the super large hole spools as well as the slightly to big. This works as its super easy to install and the rolls can not fall off the holder. I have printed one for every spool so i never have to remove it.&nbsp;2 files. 1 has nipples for extra grip, the other does not.&nbsp;Update: 1/26/24 - There has been a few suggestions to scale up to 103% as well as a need for one with a smaller filament need. I uploaded a new profile that is both larger and has a few areas cut out. Larger does not work on all spools. It does work well for Giant arm filament.&nbsp;<h3>Please &#34;Like&#34;, review, follow and upload make.</h3>&nbsp;<h3>Commercial license</h3>As of 2/25/24 my designs are no longer allowed to be sold commercially.Do you want to sell prints of this model or any of my models? You can purchase commercial licensing at <a target="_blank" href="http://www.patreon.com/ErraticallyEccentricCreations" rel="nofollow noopener">Patreon</a> or Buy Me A <a target="_blank" href="https://www.buymeacoffee.com/dohara1985o" rel="nofollow noopener">Coffee</a>.Earring and Keychain Commercial License is just $3 a month. A full commercial license for all of my designs is just $7 a month.&nbsp;Designers spend a lot of time and money on design! Supporting Patreon&#39;s is a small way to help us designers out.