yhamishmckrotch

burlpowell

PILL BOX

life stuff

vasek.vol

A mix of two different boxes.&nbsp;used screws M3x40 and M3x25 for the handlePrinted 0.2 Without supports (except lid with handle) Dimensions approx. 24.5 x 21 different compartment layouts stackable

Tool box

utility

Eric

V2 Now available. Features 3 fins that are thicker and less likely to flutter. Also features built in launch lug and shock cord attachment points on the body and nose cone. I have flown it on single stage with no issues, I plan to test dual stage mid January.&nbsp;This model rocket is design to fly on 1/2 A to C motors. There is also a capability to fly it as a two-stage rocket. Below are the open rocket models for both the single and two stage versions. This rocket should be able to fly on any A-C motor just fine, the only issue is delay charges. Shorter delay charges may cause the nose cone to eject before apogee. Please note that PAHT-CF was chosen to prevent melting of the rocket. It could possibly survive on PLA or ABS. At the bottom of the page is an example of how the rocket is put together along with how motor retention is done.&nbsp;Single:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/417772/2023-12-05_3d828c854da14.png"></figure>Single:1/2A6-2 WorksA8-5 WorksB4-4 WorksB6-6 WorksC6-6 Works&nbsp;Dual:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/417772/2023-12-05_3e518c854815e.png"></figure>B6-6 Not VerifiedC6-6 Not Verified** I will update the page as I test more motors on this rocket.&nbsp;Build:I used an old kit rocket for the parachute and shock cord. The shock is glued to paper and then to the nose cone and about an inch into the body tube. The further in the better. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/417772/2023-12-05_a2604f533b16b.jpeg"></figure>Motor Retention:Masking tape is put around the front end of the motor. I found that one single pass around the motor is enough to hold it in firmly. I need to use plyers to remove it.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/417772/2023-12-05_f7e69f26088d6.jpeg"></figure>

DarkStar Rocket

fun stuff

XentoBi

<h3>Model Description</h3>“v2” version has no label area in case you want to save even more filament. Otherwise, print the “v3” versions.The original Bambu Lab spool holder works well but takes a lot of filament and is missing a few nice features, such as being able to see how much filament is left on your spool, having passthrough holes for respooling, and more places to stick the loose end of your filament. The original locking mechanism is unchanged, and these will work interchangeably with the original version if you only want to do one side or something. The lock tab is still there for accepting the Bambu Lab refills and the original shims work as well if you want the extra locking power. I would recommend you print this in something that can withstand a dehydrator. I used ASA.I printed in 0.2mm layers without supports, with a light glue coating on the bed for ASA. &nbsp;<h3>Descrizione Modello</h3>La versione "v2" non ha un'area per l'etichetta nel caso in cui desideri risparmiare ancora più filamento. Altrimenti stampa le versioni “v3”.Il porta bobina originale Bambu Lab funziona bene ma richiede molto filamento e manca alcune caratteristiche interessanti, come la possibilità di vedere quanto filamento è rimasto sulla bobina, avere fori passanti per il riavvolgimento e più posti dove attaccare il filamento sciolto estremità del filamento.Il meccanismo di bloccaggio originale è invariato e funzionerà in modo intercambiabile con la versione originale se vuoi fare solo un lato o qualcosa del genere. La linguetta di blocco è ancora lì per accettare le ricariche Bambu Lab e anche gli spessori originali funzionano se desideri un potere di chiusura extra.Ti consiglierei di stamparlo in qualcosa che possa resistere a un disidratatore. Ho usato l'ASA.Ho stampato in strati da 0,2 mm senza supporti, con un leggero rivestimento di colla sul letto per ASA.

Bambu Lab Reusable Spool Holder

printer parts