yaikou

3D造物主

舵机切刀v2见：https://makerworld.com/zh/models/379140&nbsp;&nbsp;具体测试见哔哩哔哩【voron sb头舵机切刀测试】https://www.bilibili.com/video/BV19A4m157Jf?vd_source=c7e963c712fcfe6c78b672060f20e54b项目地址https://github.com/tdft/Stealthburner-CW2-Stealthburner-CW2-servo-cut-tip传统喷头切刀使用喷头撞击撞块来切断耗材，容易导致xy电机丢步，即使切料后回零也会因为回零重复定位精度导致层纹，还会减少部分打印行程，使用舵机切刀完美解决如上问题，通多次顿刀测试和打印测试均没遇到问题。舵机使用es08md、mg90s均可。

voron CW2舵机切刀（）

Voron

voron

planes01

<h3>Overview</h3>A-10 kit card&nbsp;Check out the <a target="_blank" href="https://makerworld.com/en/models/199176" rel="nofollow noopener">SR-71</a>, <a target="_blank" href="https://makerworld.com/en/models/242106" rel="nofollow noopener">B-52</a>, <a target="_blank" href="https://makerworld.com/en/models/436445" rel="nofollow noopener">A-10</a>, <a target="_blank" href="https://makerworld.com/en/models/402126" rel="nofollow noopener">787</a>, and <a target="_blank" href="https://makerworld.com/en/models/405459" rel="nofollow noopener">Darkstar</a>!Check out the full airplane kit card collection → <a target="_blank" href="https://makerworld.com/@planes01/collections/991821" rel="nofollow noopener">linked here</a>!<h3>Profiles</h3><ul><li>Kit Card<ul><li>plane in a kit card format ideal for gifting to others</li></ul></li><li>Model Pieces<ul><li>plane without a kit ideal for assembly right off the printer</li></ul></li></ul><h3>Filament</h3>As shown:<ul><li>Inland PLA Light Brown</li><li>Hatchbox PLA Cool Gray</li><li>Overture PLA Cement Gray</li><li>Overture PLA Space Gray</li></ul><h3>Tips</h3><ul><li>Model requires close tolerances to ensure snug but not tight or loose fit<ul><li>Make sure the model cools to room temperature before assembly</li><li>Ensure filament is properly calibrated with no excessive over extrusion</li></ul></li></ul><h3>Assembly</h3><ul><li>Remove all pieces from the kit</li><li>Debur as needed to smooth edges</li><li>Glue missile together (optional but recommended)</li><li>Let glue cure before proceeding to next step (optional but recommended)</li><li>Insert wing into forward fuselage slot</li><li>Insert engine pylon into middle fuselage slot</li><li>Insert horizontal tail into aft fuselage slot</li><li>Insert engine to pylon<ul><li>Recommend forward end first, then press down on the aft end. It will clip into place. (See gift below)</li></ul></li><li>Insert missile pylon to wing<ul><li>Recommend aft end first, then press down softly on forward end. It will clip into place. (See gift below)</li></ul></li><li>Insert vertical tail onto horizontal tail<ul><li>Recommend aft end first, then press down on the forward end. It will clip into place. (See gift below)</li></ul></li><li>Place airplane onto stand<ul><li>Recommend slot into the forward end first so that the tabs at the aft end do not accidently break</li></ul></li><li>Enjoy!</li></ul>&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000177353/design/2024-01-31_283fafe2d18ec.gif">

Voron

voron

Airplanes