xtrmgolfr

Buzzzz

<h2>Kitchen Cabinet Hook</h2>Here are 3 versions of my kitchen or bathroom cabinet hook. Each of them in plain colour or in 3 different patterns to match your decor or ambiance.<figure class="image image_resized" style="width:74.07%;"><img src="https://makerworld.bblmw.com/makerworld/draft/282736/2023-12-13_983b128142b96.jpg"></figure>&nbsp;Fits cabinet doors up to 20mm thick. I can upload different sizes if needed, just let me know.&nbsp;Two build plates uploaded:<ul><li>One with the 3 hooks in plain colour</li><li>One with each model with 4 different patterns. I do not recommend to print this plate as is as it would be a lot of wasted filament. Select the model and pattern you want to print and hide the other ones to minimize filament change</li></ul>&nbsp;Have a look at my other kitchen accessory, the Bagel Slicer:<figure class="image image_resized" style="width:73.67%;"><a href="https://makerworld.com/en/models/91382#profileId-97700" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/282736/2023-12-13_e3ab5b80b89fa.jpg"></a></figure><h4>Bambu Infill Coaster Set</h4><figure class="image image_resized" style="width:72.85%;"><a href="https://makerworld.com/en/models/98396#profileId-104858" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/282736/2023-12-18_f50946f858b9b8.png"></a></figure>&nbsp;&nbsp;And some other hooks I designed:<figure class="image image_resized" style="width:73.22%;"><a href="https://makerworld.com/en/models/87195#profileId-93445" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/282736/2023-12-13_ea0375361d81c8.jpg"></a></figure>

Kitchen Cabinet Hook

useful 

Herroc8

&nbsp;Suspension Bridge multipart. The benchy is scaled 50%.&nbsp;The suspension body include auxiliary parts to allow to print cables. This parte has to be removed with a filament cutting scissors.&nbsp;For printing is important to use 0.2mm in first layer and well calibrated tolerances.&nbsp;For assembly: &nbsp;1: Glue both road side and glue the white stripes in the midle<figure class="image image_resized" style="width:51.7%;"><img src="https://makerworld.bblmw.com/makerworld/draft/748321/2024-03-22_be7f21812f005.jpg"></figure>2. Glue both side of the bridge towers&nbsp;3. Glue the bridge body adding the road piece in the middle&nbsp;4. Insert low part of the tower in the main body to complete the bridge&nbsp;5. Insert the towers in the base.<figure class="image image_resized" style="width:35.74%;"><img src="https://makerworld.bblmw.com/makerworld/draft/748321/2024-03-22_712b702fb126c.png"></figure>6. Carefully, with a filament scissor, cut the auxiliar part of the wires.<figure class="image image_resized" style="width:49.95%;"><img src="https://makerworld.bblmw.com/makerworld/draft/748321/2024-03-22_29229a8589507.png"></figure>I suppose it should be possible to scale 150% using 0.3 layer heigh. But i havent tested it.

Suspension Bridge multipart

awards

jetpad

This model features a unique assembly of Villarceau (vee-yar-kow) circles which are elegant, ring-shaped figures that intersect each other to form a torus. To build the complete torus, you will need to print 12 sets of these paired circles, resulting in a total of 24 individual pieces. Once printed, these pieces come together in a seamless fashion, showcasing the beauty and symmetry of geometric design.&nbsp;The process of assembling the torus from these 3D-printed components is straightforward and requires no cutting or folding, making it accessible to a wide range of users, from hobbyists to educators and students. But it can be challenging to add the final circles to the torus.&nbsp;This project not only provides a tangible way to explore complex geometric shapes but also serves as a decorative piece or an educational tool. Whether you are looking to expand your collection of 3D models, engage in a hands-on project, or simply appreciate the intricate patterns of geometric forms, this torus assembly offers a rewarding and aesthetically pleasing experience.&nbsp;Printing the Villarceau Circles&nbsp;There are two sizes available: the large size produces a torus that is about 240 mm in diameter and the small size results in a 120 mm torus. On a larger 255x255 mm print bed, you can print up to 12 of the smaller inner or outer circles simultaneously. In contrast, the A1 mini can accommodate only one of the larger inner or outer circles at a time. Regardless of the printing method, a complete set requires 24 separate circles—12 outer and 12 inner circles.  Assembling the Torus&nbsp;As you put it together, pay attention to which side of each circle was on the print bed and orient them all the same way to keep the look consistent. Begin by attaching an &#39;A&#39; (outer) circle to a &#39;B&#39; (inner) circle, aligning them at the central slots. Continue adding each circle, ensuring each is shifted one slot from the last. See the videos for the details of how this is done.Complete the assembly with all but the last three outer circles. Once the remaining inner circles are in place, the next major step is connecting the torus ends, presenting a significant challenge. After linking the torus, the final task involves attaching the last three outer circles. Again, see the videos for details of how this is done.  Included are a few instructional videos for assembling paper versions of the torus, which are fully applicable to the 3D printed version. Unfortunately, there doesn’t seem to be an “easy” way to assemble them. Completing the assembly is satisfying but extremely difficult.&nbsp;<a target="_blank" href="https://youtu.be/W50J-tgBJ2M" rel="nofollow noopener">https://youtu.be/W50J-tgBJ2M</a><a target="_blank" href="https://youtu.be/4L43ncFOQTo" rel="nofollow noopener">https://youtu.be/4L43ncFOQTo</a><a target="_blank" href="https://youtu.be/rft4EJkVZ9Y" rel="nofollow noopener">https://youtu.be/rft4EJkVZ9Y</a><a target="_blank" href="https://youtu.be/-d4IQT_phlQ" rel="nofollow noopener">https://youtu.be/-d4IQT_phlQ</a>&nbsp;And here&#39;s a video of me removing and adding back the final circle to the torus. <a target="_blank" href="https://youtu.be/Q6TUq1BwdCE" rel="nofollow noopener">https://youtu.be/Q6TUq1BwdCE</a> (sorry for going out of frame). To add the final circle to the torus, start by aligning the center slots of the two circles without attempting to slide the slots together until the end. If you compress the torus, you can position all the blue slots onto the corresponding green circles. Begin at the center of the blue circle and slide it along the green circles, systematically adjusting each slot starting from the center. When you have aligned all but the last slot on one side, slide the blue circle back to the opposite side, which will position the slots on the other side near their intended interleave points. Once all the blue slots are correctly straddling the green circles, you can begin to push the green and blue slots together.&nbsp;The final circles may prove difficult to integrate into the structure. Pace yourself and don&#39;t hesitate to pause if needed. Deciding whether it’s better to attach these circles with the torus compressed or expanded can be tricky, likely requiring a mix of both methods and plenty of manipulation. Good Luck!

Sliceform Torus

must prints

Martin Kozak

Paw Patrol lookout tower with functional elevator, door and rotating monocular.&nbsp;Total height about 68 cm.&nbsp;You'll need some M2 and M3 screws and little bit of other hardware to put it together. See <a target="_blank" href="https://docs.google.com/presentation/d/1A9oc5LSpIfE7Vjarrvjy8W0-XEy0ydPLYvmmBd9ss7A/edit?usp=sharing" rel="nofollow noopener">BUILD GUIDE.</a>

Paw Patrol Lookout Tower

toys

agepbiz

<figure class="media"><oembed url="https://www.youtube.com/watch?v=6RgBXBwwXBg"></oembed></figure>&nbsp;edit: 04.03.24 added accessories - canvas top (separate print, no support needed)&nbsp;Print in place kit-card toy. Use a pair of flush cutters to separate the parts then assemble the toy. I have included both a single color version and a multicolor version. I wanted to do a project where I used several tools and machines to tie it all together into one project&nbsp;The Jeep Kit Card: <a target="_blank" href="https://makerworld.com/en/models/223303#profileId-241285" rel="nofollow noopener">https://makerworld.com/en/models/223303</a> The Trailer: <a target="_blank" href="https://makerworld.com/en/models/428258#profileId-332362" rel="nofollow noopener">https://makerworld.com/en/models/428258</a>The Gun:<a target="_blank" href="https://makerworld.com/en/models/469311#profileId-378676" rel="nofollow noopener">https://makerworld.com/en/models/469311</a>&nbsp;Subscribe or follow me on: Instagram: <a target="_blank" href="https://www.instagram.com/agepbiz/" rel="nofollow noopener">www.instagram.com/agepbiz</a> YouTube: <a target="_blank" href="https://www.youtube.com/user/agepbiz" rel="nofollow noopener">www.youtube.com/user/agepbiz</a> Twitter: <a target="_blank" href="https://twitter.com/agepbiz" rel="nofollow noopener">www.twitter.com/agepbiz</a>&nbsp;WARNING: CHOKING HAZARD - Small parts Not for children under 3 yrs.&nbsp;Printsettings: No support No raft 0,16mm layer height

Jeep Kit Card

cards

Azure3D

What should I design next?This 3D model represents a meticulously crafted Axolotl, a unique neotenic salamander known for its striking appearance and regenerative abilities. Detail-oriented and mirroring the captivating charm of its real-life counterpart, the Axolotl model features prominent fringed gills, a soft-textured body, and endearing facial details.This work is licensed under a Creative Commons (4.0 International License) Attribution—Noncommercial—No Derivatives(Check out my other 3D models)

articulated axolotl - Print in Place

cute

TreeNB(亨利方)

Update Dec.10 2023 1. Add “spool holder Max” version, more biger size spool fit in. 2. Modify the length to make two version fit in A1 mini printer.Please note that the “lite” version is recomended if you don`t have special bigger size spool. The “Max” version may not easy to be print.The rollers may partially stick with ring together, it may need you loose them by knife.&nbsp;&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/253574/2023-12-10_af125627e1908.png">&nbsp;Original---------------------------------------------------------This is a simple spool holder. it is integrated printing design and no need any screw or bears and any metal components. just fold sides and press them down as shown in GIF.<img src="https://makerworld.bblmw.com/makerworld/draft/253574/2023-12-03_e8ppooo3c78s.gif">Hope you enjoy it! and please let me know, if you have any idea to optimize this design.

Print in place spool holder with printed bearings (Dec.10 2023 updated)

printer swag

Brouk12

Easter bunny as an egg holder, its for kinder surprises and similar eggs

Bunny egg holder

holiday 

LEdiodes

batman valve caps

gifts

iLab 3D

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm - 1 loop&nbsp;Filaments Used: SUNLU Black Transmission Distance: 0.3 SUNLU Dark Gray Transmission Distance: 2.5 SUNLU Gray Transmission Distance: 3 SUNLU White Transmission Distance: 6&nbsp;Swap Instructions: Start with Black At layer #7 (0.64mm) swap to Dark Gray At layer #12 (1.04mm) swap to Gray At layer #17 (1.44mm) swap to White for the rest.