Capybara Robot

lindh3d

I designed this to be printed without support and as one piece.It will take about 1kg of plastic and over 24 hours to print. But I think this is a super nice practical print to have at home or in the garden or when camping etc…&nbsp;Made a small update to my print-in-place portable stool. I also made an instruction video on how to open it up the correct way without breaking it or cutting it open.Perfect print to use up all those leftover spools with just a few grams of filament on.The weight limit is not tested to its full potential.My weight is 85kg and a friend of my have tested it and his weight is 90kg. No problem at all. I guess it will be able to withstand 120-150kg if you sit perfectly in the center and don't wiggle on it <img src="https://static.xx.fbcdn.net/images/emoji.php/v9/t80/1/16/1f92a.png">. It's a print-at-your-own-risk thing <img src="https://static.xx.fbcdn.net/images/emoji.php/v9/t83/1/16/1f60e.png">&nbsp;Rekommended printsettings:0.4 nozzle4 Parimiters0.16 layer height15-20% infill gyroid5 top/bottom layersSupport yes : Snug Support from build platePrint mode: Arachne&nbsp;<figure class="media"><div data-oembed-url="https://youtu.be/PND58IzI9xc"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/PND58IzI9xc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><figure class="media"><div data-oembed-url="https://youtu.be/VZa5Ko11Rl0"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/VZa5Ko11Rl0" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;EDIT: 231003More pegs for more weight support.0.1mm z offset for rings. this will make them tighter at first when printing making for easier and successful print. But more force when using the stool the first time is needed.&nbsp;EDIT: 231005 Added an extra chamfer on the inside ring to be able to take more force when disassembling the first time.&nbsp;EDIT: 231022 Larger holes on the top and bottom part for larger fingers :)Removed support for holes, new design can now use regular snug support for the top holes&nbsp;EDIT: 231203 After requests, I have now made a smaller kids version. This will also fit the A1 mini printbed size.

Portable stool (twist an sit)

椅子

kevr102

When I first started to upload models onto the site, I uploaded a large size Sliding Jaw Vice/Vise, I've been learning a lot of things with the design process and now think I have a very user friendly vice, I try to design any model so that there is no need for supports etc and that's a good point with this kind of vice as there are moving parts.The initial vice sliding jaw just sat on top of the body and any flex when tightening onto an object came from the the threaded screw, this is now eliminated as the sliding jaw now runs within the rails of the main body, a much better solution, another feature is that the grub screw to hold the threaded screw drive in place is now underneath the sliding Jaw eliminating the collar on the front as on previous models, the final new feature is adding a recess to the actual thread for the grub screw to locate, some very useful additions I think.To assemble this vice, slide the sliding jaw into position, then glue the inserts on the threaded end cap and push into the main body and secure with elastic bands or similar and let it dry, then screw in the threaded drive and secure with an M5 Grub Screw, I always run an M5 Allen head bolt or standard bolt through the threads first just to clean the threads the screw in the grub screw until it meets resistance in the recess of the threaded drive and back off for a smooth action.That's about it really, another useful vice for the tool cupboard.Prints as in the screenshot of the print preview, no support needed, I print with PLA and Standard infills, It could be made stronger by printing with stronger material and higher percentage Infills of course.Thanks for Looking.&nbsp;

Large Sliding Jaw Vice

vise虎鉗

Northern Printworks

A simple little addition to add to the top of your A1/A1 Mini toolhead to allow easier removal of the Bowden tubes on hotend side if you have an AMS. These little suckers are difficult to get pressed with fingers so this tool allows you to press towards what corner you want then wiggle the tube to come out. The holes are large enough to not interfere with the Bowden tubes and toolhead movements. Check my other prints to find the A1 Bowden tube supports and the release tool for the AMS side of the A1/A1 Mini. How to use: Place your thumb under the toolhead (Make sure not hot), then use your other 2 fingers to press straight down on the releaser. Then simply use your other hand to wiggle the tube out. <img src="https://makerworld.bblmw.com/makerworld/draft/281482/2023-12-17_883d71cdb2182.gif">&nbsp;&nbsp;A1 Bowden Tube Supports:<a target="_blank" href="https://makerworld.com/en/models/78732#profileId-83046" rel="nofollow noopener">https://makerworld.com/en/models/78732#profileId-83046</a>A1 Bowden Tube Release Tool AMS Side: <a target="_blank" href="https://makerworld.com/en/models/78741#profileId-83050" rel="nofollow noopener">https://makerworld.com/en/models/78741#profileId-83050</a>&nbsp;

A1 Bowden Tube Removal Tool Tool

a1 protect 

NoycePrints

Meet Dum-E, the handy desk helper industrial robot. I designed it with purpose in mind as it can function as a phone stand, webcam mount (logitech c920) and a business card holder. It doesn&#39;t end there though, as I aim to develop this platform with further attachments in future. These may be recommended from others and/ or what I think might be useful. I hope you find it useful and please feel free to comment any recommendations for attachments you would like to see in future. I look forward to seeing your different uses/ prints and colour schemes. Thank you for your continued support :)&nbsp;To keep files from getting complicated, I have only included the phone stand attachment in this upload. I have placed optional attachments in a sperate upload available on my profile titled “Dum-E optional attachments”. This will be periodically updated with new wrist attachments I think may be of use or other people suggest. Printing helper<figure class="table"><table><tbody><tr><td>Part</td><td>Quantity</td><td>Infill</td><td>Supports required</td></tr><tr><td>Arm 1</td><td>1</td><td>25%</td><td>YES</td></tr><tr><td>Arm 2</td><td>1</td><td>25%</td><td>NO</td></tr><tr><td>Shoulder Joint</td><td>1</td><td>30%</td><td>YES</td></tr><tr><td>Wrist to attachment connector</td><td>1</td><td>40%+</td><td>YES</td></tr><tr><td>Turntable</td><td>1</td><td>20%</td><td>NO</td></tr></tbody></table></figure><figure class="table"><table><tbody><tr><td>Part</td><td>Quantity</td><td>Infill</td><td>Supports required</td></tr><tr><td>Base</td><td>1</td><td>20%</td><td>NO</td></tr><tr><td>Feet</td><td>1</td><td>20%</td><td>NO</td></tr><tr><td>XL motor</td><td>1</td><td>15%</td><td>NO</td></tr><tr><td>Large motor</td><td>1</td><td>15%</td><td>NO</td></tr><tr><td>Medium motor</td><td>1</td><td>15%</td><td>NO</td></tr><tr><td>Small motor</td><td>1</td><td>15%</td><td>NO</td></tr></tbody></table></figure><figure class="table"><table><tbody><tr><td>Part</td><td>QTY</td><td>Infill</td><td>Supports required</td></tr><tr><td>Phone stand backing</td><td>1</td><td>25%</td><td>NO</td></tr><tr><td>Phone stand bottom</td><td>1</td><td>25%</td><td>NO</td></tr></tbody></table></figure>Required for assembly Superglue for fake motor attachment and Nitrile cord.1mm nitrile rubber cord, 16cm should be enough for 1 complete arm. This is only required between joints if you intend on supporting the weight of a phone etc. Alternatively, if you have TPU filament you can use Fat Tony&#39;s handy TPU O-rings. They&#39;re a quick print and don&#39;t require superglue to fit. You can get them here: <a target="_blank" href="https://makerworld.com/en/models/205832#profileId-225948" rel="nofollow noopener">https://makerworld.com/en/models/205832#profileId-225948</a> Thanks again for the great alternative Tony!&nbsp;As an optional extra, I&#39;d recommend using 4x 3M 6mm Anti-slip sticky back rubber feet. They fit in recessed circles in the corners of the feet.&nbsp; Screws: A total of 13 are required for the arm plus 3 for the phone stand, listed below.M3x10mm - QTY 12 - available on the store, linked below.M3x15mm - QTY 3M5x30mm - QTY 1Foot: 4x M3x10mm countersunk.Base: 1x M3x15mm countersunk.Shoulder joint to Arm 2 rotation point: 1x M5x30mm countersunk.Turntable: 4x M3x10mm countersunk.Rotation point between Arm 1 and Arm 2: 1x M3x15mm countersunk.Arm 1 to wrist connector rotation point: 1x M3x15mm countersunk.Coupling attachment to wrist: 1x M3x10mm countersunk.3 M3x10mm screws are required for the Phone stand. Assembly tipsCut 3 lengths of Nitrile cord, 74, 55 and 30mm in length. Glue one side of each and cure into individual circles. These will be glued on one side between the 3 separate joints on the arm. Doing this will vastly improve the holding capacity of the arm as it will provide more friction between the joints, helping to prevent them from sagging under weight.The 74mm circle goes between the elbow joint and arm 2.The 55mm circle goes between the arm 1 and 2 joint.The 30mm circle goes between the arm 1 and wrist attachment connector.I have added 3 pictures as a guide at the end of the gallery.

Dum-E the handy desk buddy. Lamp, stand, holder 

機械

BC Designs

My filament splitter, hence the name :)&nbsp;I wanted something smaller and light weight, and more robust than the experience I've had with other more famous splitters. My version keeps the filament path totally straight for the AMS to print head route, meaning less chance of snagging and less wear and tear for the most used (imo) operation.&nbsp;Externally fed filament is fed through the hole on the side, one less connector makes the model more sleek and I really dont think its needed.&nbsp;Requires 2 x PC4 M10 pneumatic connectors&nbsp;&nbsp;PrintingThe included 3mf file is setup ready to print @ 0.12 layer height with a tiny amount of supports for the hole which will be on the outgoing feed side. Supports are on build plate only.&nbsp;I've printed 6 or 7 of these now and had zero adhesion issues. With it being a small model the minimum layer time will naturally slow the print speed down which will also help here.&nbsp;Ignore the soon-to-be-added profiles promising faster print times, you want quality for this part to print well.&nbsp;&nbsp;FittingRemove the tiny support material and fit 2 PC4-M10 connectorsMake sure the PTFE tubing is pushed fully through the connector and into the internal recess.Attach to printer, note direction arrow for correct fitting.&nbsp;

mY Filament Splitter

y接頭

君卿侧

A1辅助风扇盖子侧面风扇

a1風扇

Henlor

CAD Model of the Creality K1 CoreXY kinematics system.&nbsp;This is a work in progress. The model may contain some dimensional inaccuracies.I don't recommend to print this model as is. This model not optimized for FDM printing and is meant to be used as an asset in CAD software. <h4><img src="https://makerworld.bblmw.com/makerworld/draft/529907/2024-02-13_df513a1c80386.webp"> <a target="_blank" href="https://makerworld.com/en/models/171995" rel="nofollow noopener">Creality K1 Assembly CAD Model</a></h4><h4> </h4><h3><a target="_blank" href="https://makerworld.com/en/models/171976#change_log" rel="nofollow noopener">Change Log</a></h3>13 October 2023  First release&nbsp;<h3><a target="_blank" href="https://ko-fi.com/henlor" rel="nofollow noopener">Want to support my work ?</a></h3>Enjoy this model? Your support means the world to me! If you love what I do, remember to like and rate the model. You can also follow me to get the latest updates. If you wish to further help me to fuel future projects, consider <a target="_blank" href="https://ko-fi.com/henlor" rel="nofollow noopener">buying me a coffee</a>, I'm literally running on those! Every cup counts and is immensely valued.&nbsp;&nbsp;

Creality K1 CoreXY Motion Assembly CAD

創想k1風罩

Eden-LAB

<h2>Stress test supports. PLA printing with PETG interface supports</h2>&nbsp;I created a test to try printing in PLA (in white in the photos) with interface supports in PETG (in black in the photos). From my results I believe that PETG interface layers resolve very well the defects that are created when using supports.<h4>I recommend modifying and then saving the print profile. I made the print quickly (0.2 mm layer) but if you want you can set the same parameters with a lower layer height.</h4>&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-04_d5247748d6cfc.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-04_1c7cb439f2254.jpg">&nbsp;&nbsp;<h3>SIMPLE REMOVAL</h3><figure class="image image_resized image-style-side" style="width:28.38%;"><img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-08_1b9a3175aea7f.gif"></figure><figure class="image image_resized image-style-side" style="width:28.74%;"><img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-08_64f75507ea85f.gif"></figure>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<h2> </h2><h4>below macro of a 90 degree cantilevered surface. </h4><h4> </h4><h4>the part in contact with the PETG support is perfect.</h4>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-04_3d99a97a73c4e.jpg">&nbsp;&nbsp;&nbsp;<figure class="image image_resized image-style-side" style="width:27.7%;"><img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-04_99ee24377c77d.jpg"></figure><h4> </h4><h4> </h4>&nbsp;&nbsp;&nbsp;&nbsp;<h4> </h4><h4>detail of the round and rectangular hole, both with upper and lower PETG interface</h4>&nbsp;&nbsp;&nbsp;&nbsp;<h4>now the photos of the settings to put in the slicer. Please note that I put the PETG in place 3 of the ams (if you change it it must be reported in the “filament for supports” section</h4><h2> </h2><h2>Section SUPPORT</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-04_82f4989f0c6b6.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-04_d76740d567634.jpg"></figure>&nbsp;&nbsp;<h2> </h2><h2>Section OTHERS</h2>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-04_b620c4f2a503a.jpg"></figure>&nbsp;<h2> </h2><h2>FLUSCHING VOLUMES</h2>it is necessary to increase the filament change between PLA and PETG to the maximum (number 800). in my case I printed with PLA in place 2 and PETG in place 3&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/493698/2024-02-04_bc4d9cf40c8d4.jpg"></figure>

Stress test for perfect supports. PLA printing with PETG supports

test

DDAAANNNIEELLL

This allows you to mount Bambulab Anti-Vibration feets on 40x40 Vslots.TIGHT FIT: YOU NEED TO APPLY A LOT OF PRESSURE, BUT AVOID LOSING THE LITTLE FEET EVERY TIME YOU LIFT THE PRINTER.&nbsp;Assembly:4 M3x6mm Screws4 M3 hammer head nuts

Bambulab Anti-vibration Feet Adapter for 40x40 VSlot

避震

山东达文西

机械键盘键帽，用了以后打游戏不会挨老婆骂了，233333。底部是圆形十字，请先确认自己的键盘能否适用。无需加支撑打印。

机械键盘键帽，无需支撑打印

鍵盤

LLDJ3D

Luffy One Piece Hueforge model&nbsp;Quality Setting :&nbsp;Layer Height : 0.08Base Layer : 0.16100% infill&nbsp;Instruction :&nbsp;Start with Black At layer #7 (0.64mm) swap to Red At layer #12 (1.04mm) swap to Yellow At layer #18 (1.52mm) swap to White for the end.&nbsp;Please share your's print result.

Luffy One Piece Hueforge model

海賊王

guzzoenrico

Statuetta di Zoro stampata con bambu x1 carbon e dipinta a mano.

Zoro sacrifico

索隆

改名字不叫春日野樱

ams lite气动接头转接器，使进料口可以连接气动接头，进而连接铁氟龙管。使用PC4-M5气动接头。Connect the Feed port to the Teflon tubing。ues PC4-M5 。

amslite Feed port Adapter 进料口气动接头转接器

amaliteguard

3DMDesign

Meet Barbara, an adorable capybara with an oversized snout and a cute, chunky shape that's perfect for animal enthusiasts looking for a touch of wildlife. Her smooth lines make her the perfect companion for beginners and experienced collectors of cute animal figurines alike.

椅子