withbellson

Hamstah

<h2>WARNING</h2>Extreme caution should be used when modifying hotend plugs. Any damage to the plugs could render the hotend unusable, and any issues causing the plugs to not fit correctly could damage your printer. Please ensure that everything fits correctly when using this model. Please do not use excessive force when installing the grips, and please make 100% certain that the plugs fit correctly in your print head once they are applied. If the plug grips refuse to fit, don&#39;t use excessive force. Calibrate your filament and reprint. Over-extrusion can make it difficult or impossible to install the grips without damaging the plugs.&nbsp;<h2>Description</h2>I frequently change my hotends because I print most of my normal items with my 0.4mm hotend, my high detail items with the 0.2mm hotend and my CF, GF and sparkle filaments with the 0.6mm and 0.8mm hotends. I change them so frequently, I got frustrated with how fiddly it is to change the plugs in particular.&nbsp;These grips significantly speed up the swapping process and also make me much less worried about breaking the connectors on the main board. An additional bonus is it&#39;s quicker to identify my hotends by colour, and you can clearly see which hotend is installed with a quick glance through the window on the side of the printer head.&nbsp;<figure class="image image_resized" style="width:32.93%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000451390/design/2024-05-02_d00e0ee89fc48.png"></figure>&nbsp;<h2>Installation</h2>To apply the plug grips, please follow these instructions carefully. If the plugs don&#39;t fit or you feel like you are using excessive force to install them, stop and calibrate your filament. If your filament is over-extruded, it could cause the plug grips to be too tight to properly install. Please use caution and be sensible when installing this modification.<h3>- Heater Grip</h3>This is the largest plug with two thick, stiff wires.&nbsp;Slide the wings on the heater grip into the two slots from the top. Ensure that the clip on the top of the heater grip is on the top side as in the image below:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000451390/design/2024-05-02_e88b3fa0a2443.png"><h3>- Fan Grip</h3>This is the plug with four wires - one black, two grey and one white.&nbsp;Push the fan plug up through the hole in the bottom of the Fan Grip. Then clip the wings on the fan grip into the slots from the top. Ensure the black wire is on the left and the white wire is on the right when viewed from the top.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000451390/design/2024-05-02_debbe80640624.png"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000451390/design/2024-05-02_9f5326c5509c1.png"><h3>- Thermistor Grip</h3>This is the smallest plug with two thin black wires.&nbsp;Push the plug in sideways into the plug grip as depicted. There is a gap for the wire to rest in. This grip is designed to flex a little in order to allow you to squeeze the grip to release it from the connector on the main board.IMPORTANT: this plug clips into the main board. Do not use excessive force when pulling it out. When squeezed, the plug grip should release the plug from the main board - if it does not, carefully remove the grip sideways from the plug before unclipping the plug from the main board.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000451390/design/2024-05-02_4a958f9e94958.png">&nbsp;<h2>Instructions for use</h2>Once your plug grips are properly installed onto the hotend plugs, install the plugs in the following order:<h3>Step 1</h3>Slide the cable for the thermistor under the cable guard and install the thermistor plug with the cable going downward through the cable channel on the thermistor plug grip as shown.&nbsp;IMPORTANT: This plug is designed to clip into the main board. When correctly installed, you should feel resistance when you gently pull on it without squeezing the plug grip. It is extremely important that this plug is correctly installed to ensure the printer knows the precise temperature of the hotend.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000451390/design/2024-05-02_c5b7719f9c3ca.png"><h3>Step 2</h3>Plug in the heater plug with the top clip on the heater plug facing upward.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000451390/design/2024-05-02_92d7b5c484b64.png"><h3>Step 3</h3>Install the fan plug with the bottom of the grip facing left allowing the wires to come out toward the hotend. The black wire should be at the top and the white wire at the bottom. This plug grip is larger than the others to enable it to be easily unplugged first when removing the plugs in reverse order.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000451390/design/2024-05-02_b5e9ccedec2ea.png">&nbsp;<h3>Unplugging the hotend</h3>Follow the steps above in reverse:<ol><li>Unplug the fan plug</li><li>Unplug the heater plug</li><li>Unplug the thermistor plug</li></ol>As mentioned above, please use extreme care when unplugging the thermistor. If it doesn&#39;t slide out with minimal pressure, you must not use excessive force or you could damage the main board. If it won&#39;t come out easily when you squeeze the plug grip, attempt to remove the plug grip by sliding it to the right before unclipping the thermistor plug.

X1C Hotend Quick Swap Plug Grips

For the Printer

Cillu

Model made by me on Siemes NX, they are two pieces, which must be made on different plates. I didn't use any brims or supports, I used 0.16 as layer but it can also be made with other thicknesses. Container volume: 126x113x113mm.Model achievable on any Bambulab.&nbsp;&nbsp;&nbsp;Check out the bigger version of the tissue box <a target="_blank" href="https://makerworld.com/en/models/166418" rel="nofollow noopener">https://makerworld.com/en/models/166418</a><figure class="image image_resized" style="width:45.39%;"><img src="https://makerworld.bblmw.com/makerworld/draft/509725/2024-02-01_434273afea895.jpg"></figure>

Tissue Box Brick (Small version)

Brick!

Stag 3D

<h3>How to play:</h3><ol><li>Setup the base on a flat surface and place the Tetra Balance block onto it.</li><li>Take it in turns with your opponent to place the blocks onto the Tetra Balance piece. You can place the blocks with one hand only and once you have chosen a bloke you cannot change it.</li><li>Repeat until the tower eventually falls. </li><li>If you cause the tower to fall your opponent wins. </li></ol>&nbsp;

Tetra Balance Game

Games for the kiddos

Collecticraft

<h2>Knitted Easter Egg Boxes: Charm for Festive Delights</h2>Description: Get ready to celebrate Easter in style with our Knitted Easter Egg Box Collection! This delightful assortment features four unique boxes, each adorned with charming knitted patterns that exude rustic charm and warmth, perfect for adding a touch of festivity to your Easter celebrations.<h3>Key Features:</h3>Festive Knitted Designs: Each egg-shaped box boasts a different knitted pattern, from playful stripes to intricate lace, capturing the spirit of Easter with its vibrant and festive designs.&nbsp;Ideal for Easter Treats: These knitted egg boxes are the perfect size for holding Easter treats such as chocolates, candies, or small gifts. Surprise your loved ones with these adorable and functional containers!&nbsp;Thoughtful Easter Gifts: Spread joy and cheer this Easter season by gifting these knitted egg boxes to friends, family, or colleagues. They make thoughtful and unique presents that are sure to delight recipients of all ages.&nbsp;Celebrate the Easter season in style with our Knitted Easter Egg Box Collection, and make your festivities even more memorable with these charming and practical additions. Plus, with your <a target="_blank" href="https://www.patreon.com/CollectiCraft" rel="nofollow noopener">Patreon</a> subscription, you'll receive a commercial license, allowing you to use and sell these delightful creations as you please.&nbsp;Check the<a target="_blank" href="https://makerworld.com/en/models/222268#profileId-240459" rel="nofollow noopener"> first design</a> and experience the complete collection!<figure class="image"><a href="https://makerworld.com/en/models/222268#profileId-240459" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/684974/2024-03-11_6ccf0f0a13197.gif"></a></figure>

Knitted Easter Egg Boxes

Spring!

Ibaviosa Baubles

Adorable mooshroom earrings. Perfect for any Minecraft fan!

MineCraft Mooshroom Earring

Minecraft!

3DPODesigns

My wife assures me this is THE perfect bobbin. An avid cross stitch-er, my wife dictated what she did and didn't like from numerous types of bobbins, and this was the end result. Enjoy!&nbsp;Measures 37.5x41x1.5mm

The Perfect Bobbin

For the Crafts!

JonathanLevi

Remixed from: https://www.thingiverse.com/thing:4978318Original description from Thingiverse: Wellll... I tried about 10 times across 2 different printers and 3 different types of bed to get this thing to work, but the small little fragments on the bottom just would NOT stick down well enough to get to the bridging... so I decided to cut off the "nubs" on the bottom to give it a better chance of actually printing. Will report back with pictures if it actually works. For now, I'm live-streaming my attempts, first with the original design, then with my own: <a href="https://www.youtube.com/watch?v=EislDHbDtGw" rel="nofollow">https://www.youtube.com/watch?v=EislDHbDtGw</a>My first row turned out lousy... so I recommend supports just for the first row of hexagons. I mightdesign a saucer for it later, but no time for that now.

Printable Geodesic Planter

For the Plants!

Ryan Ewen

2024-04-18 Update:&nbsp;Added a taller version for cards with larger numbers on them.&nbsp;Original Description:&nbsp;A playing card holder with a slight tilt and a second row.&nbsp;No special settings needed while printing except maybe a brim to prevent the ends from warping off the bed on some printers.&nbsp;If you like this, you might also be interested in my playing card tray here: <a target="_blank" href="https://makerworld.com/en/models/23168" rel="nofollow noopener">https://makerworld.com/en/models/23168</a>&nbsp;Feel free to copy and tweak the original model on onshape (onshape is web-based and free!).<a target="_blank" href="https://www.onshape.com/en/products/free" rel="nofollow noopener">Sign up for onshape&#39;s free plan here</a><a target="_blank" href="https://cad.onshape.com/documents/0aca7562742fb557322591e4/w/6a8ae818654954cc85363443/e/4119eee1c41326d075f293cb" rel="nofollow noopener">Fork or create a copy of the project workspace here</a>