windo.ac

Wiseone

To avoid smaller items rolling around in my Tesla Model 3 (2021) frunk, I was interested in a secure post or two that I could attach items to. The Model 3 has two adjacent bolt wells in the frunk that can double as securing points.&nbsp;NOTE: Earlier Tesla Model 3 designs (prior to 2021) have a different frunk layout, so are incompatible with this part.&nbsp;My design makes use of the frunk nearby bolt wells. I designed and printed a post that is shaped with a hook and is a push fit into the bolt well. To avoid post movement, I included a thin slice of silicone tape to improve the fit.&nbsp;For temperature reasons, my posts are made with PETG. Other filaments that can withstand the warm temperatures that a car is likely to experience (eg. 60C) would be suitable, too.&nbsp;Here is my 3D design. My design may match your needs, too.&nbsp;My print is made in 1.75mm eSUN PETG Black filament, with 0.2mm layer height and 15% infill on a Bambu X1 Carbon printer. Optionally set Wall Loops = 4. No print supports, rafts nor brims required.&nbsp;I hope that you can find this print useful, too.&nbsp;Remember to leave me some feedback or even a tip to keep me enthused to make more of these drawings.

Tesla Model 3 Frunk Hook

Tesla Model 3

Emashi

One of my Meta Quest 3 controllers stand. Pretty useful, as you can place them in this stand, not laying down on the desk. Also its a nice looking display for them.&nbsp;No supports needed for it.

Meta Quest 3 controllers stand

Meta Quest

squinn

A portable cable organizer which is setup as an easy print-in-place and includes a knob on the side for conveniently winding up the cable when you're ready to pack it away.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_fd01d80e216de.gif"></figure>This model is an easy print that requires no supports, and three different sizes are provided to accommodate cables of different lengths. If you're not sure which to choose, I'd recommend starting with the “medium” size.&nbsp;After printing, you'll want to place the cable within the groove at its halfway point, close the lid (which is intentionally designed to close tightly), wind up the cord clockwise using the handle, and then extend by simply grabbing the cable by both ends.&nbsp;Update 2023-09-13:&nbsp;Alternative smooth-sided versions of all three sizes have now been added, and also the handle design was slightly adjusted to add a small fillet and chamfer to decrease the bridge distance. Here's a close-up picture of the updated handle on the knurled and smooth-sided versions:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_e75ea621224d08.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_68f2b35a6774b8.jpg"></figure>&nbsp;

Portable Cable Organizer / Winder

Tools

Bambu Lab

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013716/design/2023-09-25_28088e30b1c02.jpg"></figure>This 3D-printed mouse has a futuristic hollow shell design, revealing its internal structure. This generative design shell structure is possible only with 3D printing. Our industrial designer fully utilized the advantages of a 3D printed structure to present you with this magnificently artful mouse.&nbsp;Recommended filaments: Bambu PLA series<a target="_blank" href="https://store.bambulab.com/collections/bambu-lab-3d-printer-filament?gf_60645=279355719795" rel="nofollow noopener">https://store.bambulab.com/collections/bambu-lab-3d-printer-filament</a>If using PLA matte, metal, silk, please slowly screw in the bolt and avoid over-tightening to prevent structural damage.Print Setting: Print without support, v2.0 print profile recommendedHardware Kit: Wireless Mouse Components Kit-002<a target="_blank" href="http://store.bambulab.com/products/wireless-mouse-components-kit-002" rel="nofollow noopener">http://store.bambulab.com/products/wireless-mouse-components-kit-002</a>&nbsp;Please make sure you clean the build plate before printing and/or applying glue to prevent print failures.&nbsp;Follow the Assembly Guide or video tutorial below step by step to print and assemble your build. Refer to the Design Guide for further design and quality enhancement.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013716/design/2023-09-15_12b653452832c.png"></figure><figure class="media"><oembed url="https://www.youtube.com/watch?v=lkOg_X4qjW8"></oembed></figure>

Wireless Mouse 002

Will Print

V3 Precision

This poop chute catches the waste filament as it drops from the Bambu Lab X1 printer. This is a larger sized container than my other design.The poop chute uses a two magnets (0.5 inch diameter, 0.10 thick). The mounting hole for the magnets are cut oversized (0.51 diameter) for an easy fit. Might need to super glue the magnets in place.The cutaway o n the size serves two functions. It gives you a recessed handle to grip the poop chute when taking it off. The angled top of the cutaway helps direct the waste filament across the chute. Helps to keep the filament from bunching up directly beneath.&nbsp;Filament - I used PLA+ or PLA Carbon FiberSupport - Yes; Hybrid, AutoLayer - 0.2mmInfill - 15%3mf file using Bambu Lab Studio (slicer)&nbsp;UPDATE:The design was updated to accommodate the feet added to the X1, X1C, P1P, and P1S.The new design is poop_shoot_L_magnetic_V2&nbsp;You can find a finished Poop Chute with the magnets on our website www.v3precision.com.