webparker

Neebick

Simple carry along pill organizer with a weather resistant TPU seal built into the lid. Pocketable and strong. Stays closed and can take vigorous shaking. Fits into luggage and backpacks easily. Similar size to common battery packs. All cavities have a scooped bottom for easier removal of pills by finger.&nbsp;Tested by running under a running bathtub faucet. Do NOT submerge. This should only be considered for splashes of water/rain and dirt.&nbsp;<h3>Printing</h3>Printing is fairly straight forward:<ul><li>The inner sleeve/organizer part is printed on it's side due to the oval shape and text. No supports are necessary for the interior but there is some bridging that slower print speeds may help with.</li><li>All outer sleeve are a very easy print without any special consideration</li><li>The TPU seal needs to be print with the wide top against the plate with a small amount of supports for the outer bridging. There will be stringing due to the nature of TPU. But those areas can either be cleaned up with a hair dryer or ignored since they will covered during assembly.</li><li>The lid prints with the flat top against the plate.</li></ul><h3>Assembly</h3><figure class="image image_resized" style="width:25.67%;"><img src="https://makerworld.bblmw.com/makerworld/draft/626931/2024-02-24_b07ebba9642308.png"><figcaption>1. Clean supports from parts</figcaption></figure><figure class="image image_resized" style="width:25.88%;"><img src="https://makerworld.bblmw.com/makerworld/draft/626931/2024-02-24_1b3314aa2a4e98.png"><figcaption>2. Slide TPU seal over lid</figcaption></figure><figure class="image image_resized" style="width:25.17%;"><img src="https://makerworld.bblmw.com/makerworld/draft/626931/2024-02-24_cd7ef4ebc6a0f8.png"><figcaption>3. Snap Lid over inner sleeve (Glue adds strength)</figcaption></figure><figure class="image image_resized" style="width:25.05%;"><img src="https://makerworld.bblmw.com/makerworld/draft/626931/2024-02-24_d0a98e3c3624c8.png"><figcaption>4. Insert Inner Sleeve into Outer Sleeve</figcaption></figure>

Weather Resistant Sealed Pill Organizer

Backpacking

emmaginn

Planter with a stand and water drain on the bottom with a bowl to catch excess water. Orient the planter on its top and you shouldn&#39;t need any supports. Hope you like it!&nbsp;Commercial Licensing: <a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Patreons</a> also have the opportunity to use commercial licenses for their own creative projects, adding versatility and potential income streams.&nbsp;If you like this, please be sure to check out my <a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Patreon</a> where I upload many of my designs exclusively for members. Hope you like them!&nbsp;<figure class="image image_resized" style="width:57.27%;"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000169715/design/2024-05-06_43c269eba0e6.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Stacker Planter/Vase with Hidden Drip Tray</a>&nbsp;<figure class="image image_resized" style="width:58.89%;"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000169715/design/2024-05-02_c4986346dbaf9.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Rivers Planter with Hidden Drip Tray</a> <figure class="image image_resized" style="width:58.58%;"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000169715/design/2024-05-02_ac819f1c0e73c.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Slice Planter with Hidden Drip Tray</a> <figure class="image image_resized" style="width:55.7%;"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000169715/design/2024-05-02_351443b9c636b.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Ripple Propagation Planter with Stand</a>

Modern Planter With Stand and Water Catch Bowl

Planter

cyanidesugar

Everyone's favourite Space Station, now hueforged and ready to be displayed wherever you like! &nbsp;Another simple print-in-place model without supports needed, though it does take about 5 hours to print due to the details of the ‘Space’ portion of the print. I used 5 colours for this print, but you can get away with 4, by repeating the second colour - blue-grey (you can use grey) for the Death Star. &nbsp;If you are using the one-click printing on Makerworld, all settings will have been applied to the print. If you are not, or if you want to customise some of the settings yourself, please use the instructions/recommendations below: &nbsp;Print Instructions:<ol><li>For the Hueforge portion (0mm - 2.00mm) print at 100% infill with a layer height of 0.04mm with a base layer of 0.2mm</li><li>For the Death Star portion (2.04mm - 35.28mm) print at 5% infill (I used Gyroid) at 0.16mm layer height, with 3 walls, 3 top and 3 bottom surfaces. </li><li>You can make this print bigger if you want, but only change the X and Y dimensions, and not the Z dimension. </li></ol>Filaments Used: - PLA Flashforge Burnt Titanium Transmission Distance: 6.8 - PLA BambuLab Basic Blue Gray Transmission Distance: 3 (You can use grey here!) - PLA Sunlu Lilac Transmission Distance: 6.6 - PLA Kingroon White Transmission Distance: 8- PLA Overture Light Grey (for the Death Star, and you can repeat above grey if you want)&nbsp;Swap Instructions: - Start with Burnt Titanium - At layer #15 (0.76mm) swap to Blue Gray - At layer #20 (0.96mm) swap to Lilac - At layer #31 (1.4mm) swap to White for the rest.- At layer #45 (1.96mm) swap to Light Grey (the Death Star!)&nbsp;The model for the Death Star should be linked in this page (if I did it correctly!). It's a brilliant model, and if you have the time to spare, absolutely print a full sized version of it for yourself! ____________________________________ Commercial License to Sell PrintsIf you want to sell any physical models I have uploaded anywhere, an unrestricted commercial license is available on the $10AUD tier of my <a target="_blank" href="https://patreon.com/cyanidesugar3DP?utm_medium=clipboard_copy&utm_source=copyLink&utm_campaign=creatorshare_creator&utm_content=join_link" rel="nofollow noopener">Patreon</a>! ____________________________________

That's No Moon - Hueforge Hybrid Print

starwars

Big Plate Chicken

New design, assemble your cyber dragonfly, and we recommend using color printing! We have separated the wings, so if you have a multi-color 3D printing system, you can try combining the model for printing. We recommend using a body with a wall thickness of 1.2mm If you like this model, please give it a ❤️ to show your support. For the latest updates, visit <a target="_blank" href="https://twitter.com/BPCSbpcs" rel="nofollow noopener">https://twitter.com/BPCSbpcs</a>

Cyber Dragonfly (Assembly Required)

presents

omfgitsjimmy

Needed buckles for a project, couldn't find one I liked, so I made this one.

2 Inch Buckle

leather

DesignCraft

This adapter system wraps the edges of a CREALITY CR-PLA MATTE 1kg 199x68mm cardboard spool in order to:<ul><li>provide smooth rotation within a Bambu Lab AMS</li><li>prevent carboard debris from depositing within a Bambu Lab AMS</li></ul>Features:<ul><li>Reusable</li><li>CREALITY nameplate for easy identification when reusing</li></ul>Instructions:<ul><li>Measure your spool first to ensure it matches the specified dimensions</li><li>Print this model twice for a single spool</li><li>Affix one spool ring adapter on each side of the CREALITY CR-PLA MATTE spool</li><li>See attached photos</li></ul>Considerations:<ul><li>Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.</li><li>Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.</li><li>AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">AMS Lid Riser</a> which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on <a target="_blank" href="https://makerworld.com/en/u/243407759" rel="nofollow noopener">my profile</a> or directly here: <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">https://makerworld.com/en/models/33133</a></li></ul>

CREALITY CR-PLA MATTE Bambu Lab AMS Cardboard Spool Adapter Ring

tools

ABDELat

All gridfinity basic bins, starting with 1x1x1 up to 6x6x12. Each file includes all heights from 0 (lid) to 12 (87.55 mm).&nbsp;These bins don&#39;t have magnet/screw holes. As long they are used for Drawers or non-moving places you don&#39;t need them.<ul><li>no labeling tab</li><li>labeling tab on the left side</li><li>labeling tab on the right side</li></ul>The generated 3mf-files are all based on this <a target="_blank" href="https://github.com/kennetek/gridfinity-rebuilt-openscad" rel="nofollow noopener">openSCAD rebuild</a>. I&#39;m using them a lot, they work as intended, easy to print.I&#39;ve include all printable profiles. The 6x6 version isn&#39;t currently printable, so there is no printable file. The 3MF-Version of each combination can also be downloaded in the raw-model-files tab.<h4>Bin Sizes in mm</h4>for all that don&#39;t want to calculate the sizes:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000047599/design/760bc579-31a2-4876-9f86-9abd4176c954.png"> <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000047599/design/44efbb41-6eed-494c-bd99-429ecba1642e.png">&nbsp;If you&#39;re looking for an easy to print grid, i recommend <a target="_blank" href="https://www.printables.com/model/430144-gridfinity-base-with-snap-connectors" rel="nofollow noopener">Gridfinity base with snap connectors</a>. If you have an Ikea ALEX drawer, <a target="_blank" href="https://makerworld.com/de/models/28581" rel="nofollow noopener">here you`ll get all needed parts (inkl. spacer)</a>.&nbsp;Other Tools used:All files are generated with the help of a modded version of <a target="_blank" href="https://github.com/OutwardBuckle/OpenSCAD-Bulk-Export" rel="nofollow noopener">OpenSCAD-Bulk-Export</a>. Check out this git if your interested in bulk-exporting from OpenSCAD&nbsp;Printing:Print it in any material you like. For most applications PLA is good enough. The slicer recommends a brim. With a bit of glue or the textured PEI sheet it doesn&#39;t move.The 6x6 can`t be printed in one piece! Use the Slicer to split it as you like.I´ve in also included print-profiles for all versions.&nbsp;Additional Tools and Helpers<ul><li><a target="_blank" href="https://makerworld.com/models/208796" rel="nofollow noopener">Gridfinity Height ruler - slim Edition</a>: Helps you to find the correct bin height.</li><li><a target="_blank" href="https://makerworld.com/en/models/476336" rel="nofollow noopener">AIO parametric Gridfinty Project</a>: Generate you own gridfinity bin.</li><li><a target="_blank" href="https://makerworld.com/en/models/28581" rel="nofollow noopener">Slim Gridfinity Base for Ikea Alex:</a> Perfectly fitting grid for Ikea Alex Drawer</li></ul>&nbsp;<h3>Parametric Model Maker</h3>I&#39;ve made a SCAD Version to work with the new <a target="_blank" href="https://makerworld.com/en/makerlab/parametricModelMaker" rel="nofollow noopener">Parametric Model Maker</a>. Just download the “Makerworld.scad” (from Raw Files) and use it there. In the Customize Section, you can change most parameters the get the desired Bin you want. Use the button right next to do Download or <a target="_blank" href="https://makerworld.com/en/makerlab/parametricModelMaker?designId=47599&amp;from=model_page&amp;scadUrl=https%3A%2F%2Fmakerworld.bblmw.com%2Fmakerworld%2Fmodel%2FUSd2da6c53f14d3c%2Fmsfile%2F2024-04-16_1fd4308bde644.scad&amp;type=user" rel="nofollow noopener">use this link.</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000047599/design/2024-05-10_09f49611aee0f.webp"><figcaption>Quick preview of the parametric model maker</figcaption></figure><h3>How to download the RAW files</h3>Since the last UI change the download option is a bit hidden. This is the current way to download the RAW files or the File for the <a target="_blank" href="https://makerworld.com/en/makerlab/parametricModelMaker" rel="nofollow noopener">Parametric Model Maker</a>.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000047599/design/2024-05-03_e07cda6ec065f.jpg"></figure><h3>Share your makes and support me</h3>If you like my work, give it a 🚀 boost 🚀 (the button is right below the Download). You can <a target="_blank" href="https://brickbank.app/support/" rel="nofollow noopener">support me here</a>, via <a target="_blank" href="https://ko-fi.com/brickbankapp" rel="nofollow noopener">Ko-Fi</a> or <a target="_blank" href="https://patreon.com/brickbankAPP" rel="nofollow noopener">Patreon</a>. Please leave a comment or share your makes 😁.  I appreciate your support! If your interested in selling the printed models DM me.&nbsp;Updates:2024-02-04: in the raw files section you can find premade zip-files wiht all generated boxes for each size, starting with 01x01x00 up to 12x12x12. This should help to create any box combination you like. Note: not all files can be printed as one piece! All zip files together are ~ 1.25GB i recommend to download them one by one!