wanyixing2018

打客Side_ReverSea

Print in place lid box 一体打印入滑盖无限组合零件收纳盒 french cleats system wall mount modular linkable.20240310 更新两款盖子图案设计。20240311 更新可插69.8MM宽标牌的版本。 use 69.8 wide 4mm Dia round corner 1 mm thick label.20240312 更新可插69.8MM宽标牌的版本。 use 69.8 wide 4mm Dia round corner 1 mm thick label double size version.&nbsp;

Printinplace lid box french cleats 一体打印组合零件收纳盒 洞洞板

一体打印组合零件收纳盒 洞洞板

brody.bolanos

Bambu Lab P1 / X1 Series Modular Bentobox Aux Fan (4/10/2023)Designed a modular second aux fan / bentobox for Bambu Lab printers. Assuming a lot of people will upgrade their P1P to the P1S, they will most likely have 2 aux fans now and this could be a good use for the 2nd one! This is separate from my other model ( <a target="_blank" href="https://makerworld.com/en/models/23644" rel="nofollow noopener">https://makerworld.com/en/models/23644</a> ) as this is meant for users that plan on using the printer in a both enclosed or open environment. Use the dual aux when printing PLA or filaments that need cooling in a non-enclosed setting. Switch over to the bentobox when printing enclosed with filaments that can release unpleasant or harmful odors. The bentobox will recirculate the air, passing it through the filters and ideally removing any odors. &nbsp;Contents<ul><li>Updates</li><li>Files</li><li>Additional Parts</li><li>Printing Information</li><li>Assembly</li><li>Wiring Options</li></ul>The X1 and P1 Version are different! This is to account for the Lidar clearance.&nbsp;This will only fit on the right side of the printer! You cannot mirror to work on the left, where the original fan goes, as the frame rails are are different heights ( among other things). <h4>Future Update (8/15/2023)</h4><ul><li>Working on an update that will mount the fan to the side panel. Now that P1 users have that option, it will be a faster print, save filament and save space if the fan base is no longer need. <ul><li>See “Test” folder, currently waiting on the new panels to verify fitment - 8/25/2023</li></ul></li></ul><h4>Update 7/28/23 </h4><ol><li>Finished the design for the upgraded fan ducts that provide airflow to the back, middle, and front of the build plate<ol><li><a target="_blank" href="https://makerworld.com/en/models/23661" rel="nofollow noopener">https://makerworld.com/en/models/23661</a> </li></ol></li></ol><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_9nmybmxrx1es.png"></figure><h4>Update 7/25/23 </h4>Added multiple wiring instructions.<ol><li>Using fan_1 port to power the aux. Control via Bambu Studios</li><li>Using fan_1 port to power the aux. Control via Gcode.</li><li>Keeping the fan_1 port open for the chamber temp fan, wiring 2nd aux to the 1st aux fan. Control via normal way.</li></ol><blockquote><h3>Files</h3></blockquote>Main Files<ol><li>Back Plate 3A</li><li>Dual Fan Stand 4A</li><li>Fan Case 6A</li><li>P1 Modular Fan Top 7A</li><li>X1 Modular Fan Top 8A</li></ol>Optional Bentobox Files<ol><li>HEPA Box 1A</li><li>HEPA Cover 2A</li><li>Carbon Box 5A</li></ol>Print File<ol><li>P1 Print File</li><li>X1 Print File</li></ol><blockquote><h3>Additional Parts </h3></blockquote>Base Components <ol><li>Aux fan <ol><li><a target="_blank" href="https://us.store.bambulab.com/products/auxiliary-part-cooling-fan-x1-series-and-p1p" rel="nofollow noopener">https://us.store.bambulab.com/products/auxiliary-part-cooling-fan-x1-series-and-p1p</a></li></ol></li><li>Qty 2 : M3*6</li><li>Qty 24: 6mm*3mm round Neodymium Magnets<ol><li><a target="_blank" href="https://www.amazon.com/dp/B09TQP1KZ5?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">https://www.amazon.com/dp/B09TQP1KZ5?psc=1&ref=ppx_yo2ov_dt_b_product_details</a></li></ol></li></ol>Optional Components for Bentobox<ol><li>Qty 1 : 80mm*40mm*15mm HEPA Filter<ol><li><a target="_blank" href="https://www.amazon.com/dp/B0782T7L6P?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">https://www.amazon.com/dp/B0782T7L6P?psc=1&ref=ppx_yo2ov_dt_b_product_details</a></li></ol></li><li>Acid-Free Carbon Pellets - Minimum 4mm Diameter<ol><li><a target="_blank" href="https://github.com/nevermore3d/Nevermore_Micro#sourcing-the-proper-acid-free-carbon" rel="nofollow noopener">https://github.com/nevermore3d/Nevermore_Micro#sourcing-the-proper-acid-free-carbon</a></li></ol></li></ol><blockquote><h3>Print Orientation</h3></blockquote><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_if06atl7nsy4.png"></figure><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_wu8wyw2misk2.png"></figure><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_opljwm8e6mbh.png"></figure>&nbsp;<blockquote><h3>Print Settings</h3></blockquote>DO NOT USE PLA, IT WILL BREAK. Please use PETG, ASA, PLA+ , etc. I used Polylite Pro PLA+Set your K calibration and adjust setting based on your filament Quality<ul><li>Please see build plate file. </li></ul>Support <ul><li>Please see build plate file. </li></ul>Other<ul><li>Bed adhesion - use brim if you're having adhesion issues, its already configured in the print file so please go over the settings first. </li></ul>* To remove the support from the fan top , I just used pliers and pulled the support out which was pretty easy. Sometimes some of the support stuck but it was easy to clean up with a small knife. The supports on the 2 larger tabs on the fan casing should looked at after the supports are removed, just make sure it's clean on the bottom side since these tabs are what hold it tight against the fan stand. &nbsp;<blockquote><h3>Assembly</h3></blockquote><ul><li>Remove the fan from casing, remove the sticker over the wiring and redirect the wiring as shown below. Don't put the fan in the printed case yet. </li></ul><figure class="image image_resized image-style-align-center" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_h8qchxo18x22.jpg"></figure><ul><li>Glue in the 24 magnets<ul><li>3 on the stand</li><li>6 on the carbon box</li><li>8 on the HEPA box</li><li>4 on the HEPA cover</li><li>1 on the back plate</li></ul></li></ul>&nbsp;<ul><li>Place the fan into the new casing, make sure the fan is centered by using the alignment poles</li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_l8sga615s3jd.png"></figure><ul><li>Attach the back plate using re-using the 3 screws that originally held the fan into the casing. Tighten the screws 90% of the way making sure the backplate can still move a little.</li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_ivz5jsbdv186.png"></figure><ul><li>Slide the upper assembly onto the fan stand, same way as the OEM aux fan and use the 2 longer screws that come with the aux fan to tighten the case against the stand. Then make sure the back plate is squared up and tighten the 3 screws the remainder of the way.</li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_m97ksiyhwtqh.png"></figure>MOVE THE BUILD PLATE ALL THE WAY DOWN FOR THE NEXT STEPS<ul><li>The stand connects to the floor via lining up the L shape cutout with the L shape extrusion on the floor. There is also a caution sticker and under that sticker is a hole that we will use to screw the stand to the floor. I re-used 1 of the 2 shorter screws that came with the aux fan. </li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_rpgsoq1t540w.png"></figure><ul><li>Assemble the carbon box, HEPA box, HEPA cover. </li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_gdp6slsnyzis.png"></figure><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_uq7vh8ci03r6.jpg"></figure><ul><li>Rotate filter cover around ( the protrusion gets in the way of the bentobox) or use on the the below models<ul><li><a target="_blank" href="https://makerworld.com/en/models/23650#profileId-22261" rel="nofollow noopener">https://makerworld.com/en/models/23650#profileId-22261</a> </li></ul></li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_bxot5dhpbn0y.jpg"></figure><blockquote><h3>Bentobox</h3></blockquote><ul><li>To use the bentobox, slide the assembly onto the fan casing. The top of the HEPA filter cover needs to overcome the protrusion on the frame so it takes a little bit of force to push into place. Then use 2 M3x6 to hold in place.<ul><li>Once everything is printed, in place, and screwed down, the model will clear the printing plate. </li></ul></li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_hwr0s8qnv8na.png"></figure><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_4cla5v0yk5ma.png"></figure><blockquote><h3>Dual Aux</h3></blockquote><ul><li>Slide the fan top onto the fan casing and use 2 M3*6 screws to hold into place. <ul><li>Once everything is printed, in place, and screwed down, the model will clear the printing plate. </li></ul></li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_9lydrevbtgtz.png"></figure>&nbsp;<blockquote><h3>Wiring Options ( Option 3 is the best and requires no modifications to the existing aux fan wires)</h3></blockquote><h3>Option 1- Using the fan_1 port ( where the chamber fan would connect) and Bambu Studios to control the fan. </h3><ul><li>Follow the instructions to remove the back plate to plug in the aux fan. The fan plugs into Fan 1 while the original aux fan is plugged into Fan2</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_4maaef750gs9.jpg"></figure><ul><li>Cable manage the wiring </li></ul><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_la2mod8h0fai.jpg"></figure><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_6xjjld9r753r.png"></figure><h4>Bambu Studio</h4>So I know you can change the Gcode to make it work with the fan which is “M106 P3 S0 ; turn off chamber fan” (option 2 below) but you can also change the config to make it show up in Bambu Studio.<ul><li>For me on PC it's under C:\Program Files\Bambu Studio\resources . Open the Config file with an application like Notepad++ <a target="_blank" href="https://notepad-plus-plus.org/downloads/v8.5.1/" rel="nofollow noopener">https://notepad-plus-plus.org/downloads/v8.5.1/</a></li><li>Under "FUNC_CHAMBER_FAN" : false," change it to true ""FUNC_CHAMBER_FAN" : true," . Notepadd++ will ask to change this under administrator, click yes and save the file. </li></ul>{ "printers": [ { "display_name": "Bambu Lab P1P", "func": { "FUNC_CHAMBER_TEMP": true, "FUNC_FIRSTLAYER_INSPECT": false, "FUNC_AI_MONITORING": false, "FUNC_BUILDPLATE_MARKER_DETECT": false, "FUNC_FLOW_CALIBRATION": false, "FUNC_MONITORING": false, "FUNC_MEDIA_FILE": false, "FUNC_REMOTE_TUNNEL": false, "FUNC_LOCAL_TUNNEL": true, "FUNC_VIRTUAL_CAMERA" : false, "FUNC_PRINT_WITHOUT_SD": false, "FUNC_ALTER_RESOLUTION": false, "FUNC_CHAMBER_FAN" : false, "FUNC_EXTRUSION_CALI": true, "FUNC_PRINT_ALL" : false<ul><li>Re-open Studio and on the device screen you'll now see the chamber fan which is what we'll use to control the 2nd aux fan. </li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_s1q2y4ab0xi0.png"></figure>&nbsp;<ul><li>For the bentobox air flow, you only need to set a fan speed until you feel a breeze coming out of the top filter. </li></ul><h3>Option 2 - Using the fan_1 port ( where the chamber fan would connect) and Gcode to control the fan. </h3><ul><li>Same wiring as above but instead of changing the config file for Studios we change the gcode. This was suggested from @bjws_297864:<ul><li>Remove the filament start code that modifies the chamber fan and added this to the end of the printer start gcode: ;========turn on chamber fan to filter VOCs ============= {if filament_type[initial_extruder]=="ABS" || filament_type[initial_extruder]=="ASA" } M106 P3 S50 ; set chamber fan to 20% {endif}</li></ul></li></ul><h3>Option 3 - Wire the 2nd aux fan to the original aux fan. This way both fans are controlled as one without needing to change any code. This is how I have mine set up. </h3>What's required:<ol><li>JST MX 1.25 Connectors<ol><li><a target="_blank" href="https://www.amazon.com/gp/product/B0B3MSD154/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1" rel="nofollow noopener">https://www.amazon.com/gp/product/B0B3MSD154/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1</a> </li></ol></li><li>Minimal soldering skill</li></ol><h4>Wiring Diagram </h4>Bambu wiring = Dark grey (GND) , Black (+), light grey ( tach) , white (pwm)<figure class="table"><table><tbody><tr><td> </td><td>Bambu </td><td>JST MX 1.25</td></tr><tr><td>+</td><td>Black</td><td>Red</td></tr><tr><td>-</td><td>Dark Grey</td><td>Black</td></tr><tr><td>Tach</td><td>Light Grey</td><td>Yellow</td></tr><tr><td>PWM</td><td>White</td><td>White</td></tr></tbody></table></figure>As pointed out by <a target="_blank" href="https://www.printables.com/@MozzieT_1023044" rel="nofollow noopener">@MozzieT_1023044</a> if you're wiring the 2nd fan into the existing one, it's probably best to only connect the PWM wire and not the Tach wire. The speed readout may get a bit confused as to the actual fan speed if the two fans pulses don't align for whatever reason. I still have my 2nd tach wire connected without any issues but I do plan on disconnecting it next time I take my panel off. -9/8/2023<figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_7idliu8ym2h5.png"></figure><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_8ivrxuvjho5o.jpg"></figure><ul><li>Behind the power panel, there are two screws under -V and +V that aren't being used. I just wrapped the wire around these screws and tightened down. You should use a terminal ring but I didn't. </li></ul><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_j393m510343b.jpg"></figure>And finally how it all looks wired up:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/205537/2023-09-27_4so3n2cujura.jpg"></figure>That's all! &nbsp;If you like my designs and want to say thanks, you can buy me a coffee and help fund the filaments I need for prototyping. A donation of any amount to <a target="_blank" href="https://www.buymeacoffee.com/brodyB" rel="nofollow noopener">Buy Me a Coffee</a> or <a target="_blank" href="https://paypal.me/brodyb10?country.x=US&locale.x=en_US" rel="nofollow noopener">PayPal</a> would be greatly appreciated!&nbsp;As always, given different printing environments, filaments, etc., prints may not work perfectly for everyone. If you are having issues please message or comment and I will try my best to resolve the issue.

Bambu Lab P1 X1 Dual Aux Fan / Bentobox 7/28 Updated

Bambu Lab P1 X1 双辅助风扇

<h3>Bambu Lab MC Board Fan Noctua Upgrade</h3>Designed to improve cooling to the control board heatsink using: Noctua NF-A4x10 5V PWM , NF-A4x20 5V PWM or the original Bambu MC fan.&nbsp;<blockquote><h3>Files</h3></blockquote>Noctua Fan STL<ol><li>Noctua Fan 35x18</li><li>Noctua Fan 39x22</li><li>Noctua Fan 38x20</li><li>Noctua Fan 40x40x20 38x20</li><li>Noctua Fan 40x40x20 35x18</li></ol>Bambu Fan STL<ol><li>Bambu Fan 38x20</li><li>Bambu Fan 35x18</li><li>Bambu Fan 39x22</li></ol>Print Files<ol><li>Bambu Fan Print Files</li><li>Noctua Fan Print Files</li></ol>&nbsp;<blockquote><h3>Fans</h3></blockquote><ul><li>Noctua NF-A4x10 5V PWM<ul><li><a href="https://a.co/d/5Trh12O" rel="nofollow">https://a.co/d/5Trh12O</a> </li></ul></li><li>Noctua NF-A4x20 5V PWM<ul><li><a href="https://a.co/d/8Tra4lA" rel="nofollow">https://a.co/d/8Tra4lA</a> </li></ul></li><li>Bambu Control Board Fan<ul><li><a href="https://store.bambulab.com/products/control-board-fan" rel="nofollow">https://store.bambulab.com/products/control-board-fan</a> </li></ul></li></ul>NF-A4x10 is what I’m using , it's quiet and has 5.24cfm. I have models for the NF-A4x20 as some users already have it but since it's 10mm thicker, there isn't as much space to redirect the air before the heatsink. Not sure how much that matters, just putting it out there. &nbsp;<blockquote><h3>Print View</h3></blockquote><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/152407/2023-09-27_eekoumltyjvn.png"></figure>&nbsp;<blockquote><h3>Print Settings</h3></blockquote>I used Polylite Pro PLA+, no issues so far. Set your K calibration and adjust setting based on your filament Open the print file to see the rest of the settings. &nbsp;<blockquote><h3>Instructions</h3></blockquote>Please determine what size heatsink you have in order to choose the correct model. There are 3 different heatsink sizes Bambu has used. <ul><li>35x18 - Horizontal fins</li><li>38x20 - Vertical fins</li><li>39x22 - Unsure (more on this below)</li></ul>According the Bambu <a href="https://wiki.bambulab.com/en/p1/maintenance/mc-board" rel="nofollow">https://wiki.bambulab.com/en/p1/maintenance/mc-board</a> the P1P has vertical fins and the the P1S has horizontal. “The P1P board has a vertical orientation heatsink to help with natural convection cooling when used without a fan, while the P1S heatsink has a horizontal heatsink orientation for side MC Fan cooling”. <figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/152407/2023-09-27_5tfyjio5r979.png"></figure><h4>G-Code</h4>If you are a P1P user please follow to G-code instructions below to activate the MC fan. <ul><li><a href="https://wiki.bambulab.com/en/p1/manual/kind-reminder-for-P1P-enclosure" rel="nofollow">https://wiki.bambulab.com/en/p1/manual/kind-reminder-for-P1P-enclosure</a> </li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/152407/2023-09-27_i9vlfdx1gy09.png"></figure>&nbsp;<h4>Install</h4><ul><li>Install onto the heatsink, no need to remove anything as it's able to slide right into place. You might need to move/manage some of the wires though. </li></ul>&nbsp;<ul><li> 39x22 Heatsink <ul><li>If anyone has one of these can you please let me know how the fitment is, as well as take a measurement of the fin height? The fan casing should be ~2-3mm away from the rear panel so I will most likely need to adjust the height of the 39x22 model. </li><li>Once I'm able to validate the height of the 39x22 I can add the side vents like the other 2 models have and I can create a version for the 20mm Noctua fan. </li><li>For reference, the fins on the 35x18 have a height of 21mm and the 38x20 is 30mm. </li></ul></li></ul><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/152407/2023-09-27_6amgvqyn4vhv.png"></figure>&nbsp;<h4>Noctua Wiring </h4><ol><li>JST MX 1.25 Connectors<ol><li><a href="https://www.amazon.com/gp/product/B0B3MSD154/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1" rel="nofollow">https://www.amazon.com/gp/product/B0B3MSD154/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1</a> </li></ol></li></ol><figure class="table"><table><tbody><tr><td> </td><td>Noctua NF-A4x10 PWM 4 Pin</td><td>JST MX 1.25</td></tr><tr><td>+</td><td>Yellow</td><td>Red</td></tr><tr><td>-</td><td>Black</td><td>Black</td></tr><tr><td>Tach</td><td>Green</td><td>Yellow</td></tr><tr><td>PWM</td><td>Blue</td><td>White</td></tr></tbody></table></figure><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/152407/2023-09-27_za4s1w7qiegh.jpg"></figure>Please refer to P1P to P1S upgrade kit installation tutorial for any further instruction. <a href="https://wiki.bambulab.com/en/p1/manual/p1p-to-p1s" rel="nofollow">https://wiki.bambulab.com/en/p1/manual/p1p-to-p1s</a> If you like my designs and want to say thanks, you can buy me a coffee and help fund the filaments I need for prototyping. A donation of any amount to <a href="https://www.buymeacoffee.com/brodyB" rel="nofollow">Buy Me a Coffee</a> or <a href="https://paypal.me/brodyb10?country.x=US&locale.x=en_US" rel="nofollow">PayPal</a> would be greatly appreciated!<h3>As always, given different printing environments, filaments, etc., prints may not work perfectly for everyone. If you are having issues please message or comment and I will try my best to resolve the issue.</h3>

Bambu Lab MC Control Board Fan Noctua Upgrade

Bambu Lab MC 控制板风扇夜行升级

nyx_nk

As soon as my P1P arrived, one of the first things I did was install an enclosure and build an air filtration system inside the chamber. I found the BentoBox project very interesting and so I printed it immediately. However, later the need arose to install a second auxiliary fan to cool the parts, but the presence of the BentoBox precluded its installation. I therefore solved this problem by creating a support for the aux fan that integrated all the components of the BentoBox inside. It wasn't easy to fit everything into such a small space, but I think I succeeded. The filtering system and the aux fan are powered independently and, via a switch, you can turn the filtering on or off as you wish. Aesthetically it's not the best, but it works very well.&nbsp;<h4>ASSEMBLY</h4>First of all, remove the supports highlighted in orange in the following image.<figure class="image image_resized" style="width:46.95%;"><img src="https://makerworld.bblmw.com/makerworld/draft/211115/2023-11-10_2566048bdcacc.png"></figure>Install all the 22 magnets (5x1.5 mm) in the appropriate seats, paying attention to the polarities.Now proceed with the wiring. First, pass a 2-pole cable for the switch inside the piece following the arrows in the following images. Solder to the switch (KCD1-101 model) and fit the switch.For the wiring diagram of 5015 fans (very easy), consult the original BentoBox project (https://www.printables.com/model/387994). Place the switch contacts in series with the + of the power supply. It is suggested not to connect directly to the printer transformer, but to insert a connector (JST e.g.) so as to make any temporary removal easier.Fix the 5015 fans with 4 M4x25 screws.Insert HEPA filter (80x40x15mm) in its place and fill the carbon box with carbon pellets.To place the filtering system, simply position the piece using the appropriate joint and then fix it to the base of the printer using a screw to be inserted as shown in the following figures.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/211115/2023-11-10_299887b5db9f3.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/211115/2023-11-10_bf3966dd47dcd.jpg">&nbsp;Insert the carbon box and close everything with the two printed covers.Filtering system is now completed.&nbsp;The assembly of the auxiliary fan is very simple: match the fan duct with the case using the appropriate track and glue for a better seal. Mount the fan core purchased on the BambuLab website. Place the fan on the filter system and screw with the screws supplied with the original aux fan (the two large ones below and the two small ones to the printer frame). For wiring, refer to this project: https://www.printables.com/model/435312<figure class="image image_resized" style="width:58.4%;"><img src="https://makerworld.bblmw.com/makerworld/draft/211115/2023-11-10_49431318f6d92.jpg"></figure><figure class="image image_resized" style="width:58.37%;"><img src="https://makerworld.bblmw.com/makerworld/draft/211115/2023-11-10_9e4c85c514b65.jpg"></figure>&nbsp;If everything has been assembled correctly, there should be no contact with the print head or the bed.

BentoFan (Dual fan + independent air filtering for BambuLab P1P/P1S)

BambuLab P1P/P1S 的双风扇 + 独立空气过滤

Miss

古风灯

niltsh

Updated @ Jan, 22nd, 2024&nbsp;I've noticed some feedback that my default profile does not perform well on A1 series, mainly because of the overhang of the barrel and main body.As I don't have a A1/A1 mini printer to verify, please be cautious if you would like to challenge on A1/A1 mini. And I would appreciate if anyone could share his/her A1 profile if succeeded.&nbsp;-----------------Story continued from <a target="_blank" href="https://makerworld.com/zh/models/39368#profileId-38480" rel="nofollow noopener">https://makerworld.com/zh/models/39368#profileId-38480</a>&nbsp;Once the kids know what their dad is capable, their dad got mind blown. So this time, I started from scratch and made them happy again.&nbsp;This model works as the thumbnail GIF demonstrated.The total range is around 7~8m, effective range is around 3~4m, should not worry about breaking your window, but I won't recommend to try it.&nbsp;The assembly manual is in the thumbnails, should not be hard for you as you have already own a printer.&nbsp;As I am not a glue fan, this time I adjusted the fitting relatively tight, especially when installing the “hand support”. My suggestion is applying some lubricant and use a small hammer gently.----------------------There are 3 parts need to be prepared separately<ol><li>bow string: the rubber diameter no more than 2 mm should be OK. I bought from <a target="_blank" href="https://www.amazon.co.jp/dp/B00A9MM86S?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">here</a> </li><li>rubber ring: I used the same rubber ring with my katana, the folding diameter is 60mm</li><li>PTFE tube: you could cut from your AMS. I did that.</li></ol>----------------------I am not a aerodynamics expert. Although I tried several approaches, I could not find a better bullet shape rather than ball shape. I really hope anyone would like to help to design a good bullet shape.&nbsp;

一体打印组合零件收纳盒洞洞板

Bambu Lab P1 X1 双辅助风扇

Bambu Lab MC 控制板风扇夜行升级

BambuLab P1P/P1S 的双风扇 + 独立空气过滤

古风灯

Hybrid Crossbow / 弩 - 神机

一体打印组合零件收纳盒 洞洞板

Bambu Lab P1 X1 双辅助风扇

Bambu Lab MC 控制板风扇夜行升级

BambuLab P1P/P1S 的双风扇 + 独立空气过滤

古风灯

Hybrid Crossbow / 弩 - 神机

一体打印组合零件收纳盒洞洞板