user_955367240

山东达文西

拓竹p1系列钢丝擦嘴，保证把喷嘴的残料擦的干干净净！亲测两周好使。喷嘴在tb上搜索“电动钢丝刷头”，购买刷头直径5mm柄径3mm的即可。安装时稍微用点力。

拓竹P1/X1钢丝擦嘴/喷嘴擦料器/The Nozzle Wiper 

补补觉去

After long-term testing and use, I found that gears with a module of 1.5 are a good choice for long-term use of 3D printed parts. They are a specification that is relatively balanced in strength and volume. Therefore, I designed a set of commonly used gears, including Spur Gears, Internal Gears, Rack Gears,90° Bevel Gear, Worm, and Worm Gears, which can basically meet daily needs.&nbsp;经过长期测试和使用，模数1.5的齿轮是3D打印零件能长期使用的较好选择，是强度和体积比较平衡的规格，所以我设计了一套常用的套装，包括正齿轮、内齿轮、90°斜齿轮、蜗杆和蜗杆齿轮，能够基本满足日常需要。&nbsp;Precautions 注意事项&nbsp;3D printed gears cannot withstand high-speed movement; plastic gears have a certain degree of self-lubrication and have better smoothness after running-in. If lubricants are needed, please choose plastic-specific lubricants;If you do not pursue a specific speed ratio, it is recommended to choose a number of teeth with no common factor for the meshing gears, so that the gears wear more evenly and have a longer life;PLA has better deformation resistance than PETG;To ensure strength, please use a lower speed and a smaller layer height to print;The thickness of the gear and the length of the connecting rod can be obtained by changing the size in the slicing software.You can also adjust the gear to suit your needs by adding parts or negative parts without changing the tooth surface.&nbsp;3D打印的齿轮不能承受高速的运动；塑料齿轮有一定的自润滑性，经过磨合有较好的顺滑度，如果需要润滑剂请选择塑料专用润滑剂；如果不追求特定的转速比，互相啮合的齿轮建议选择没有公因数的齿数，这样齿轮磨损更均匀，有更高的寿命；PLA比PETG有更好的抗变形能力；为了确保强度，请使用较低的速度和较小的层高打印；齿轮的厚度，连接杆的长度，可以在切片软件中通过尺寸改变来获得。在不改变齿面的情况下也可以通过添加零件或负零件等，来调整齿轮适用你的需求。&nbsp;If you need gears of other specifications, you can also leave a message and I will provide them one by one.如果你需要其他规格的齿轮，也可以留言，我尽可能一一提供。<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000473607/design/2024-05-24_f48a680ebb28e.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000473607/design/2024-05-24_e90ca9df2b4bf.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000473607/design/2024-05-24_4055e60b2eb1f.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000473607/design/2024-05-24_edc3408934b7c.png"></figure>&nbsp;&nbsp;

IOS Module1.5 Gears\worm set国际标准1.5模数齿轮集合 

noker

<h2>Rotary spool holder with Automatic rewinding for A1 mini 带自动回卷功能的A1 mini料盘架</h2><h3>Please be patient and read the page, thank you！ 请耐心看完页面，谢谢！</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_05790c0fbea83.png"></figure><h3>Basic Information（基本信息）：</h3>The name of the model（模型名称）：Rotary spool holder with Automatic rewinding for A1 mini（带自动回卷功能的A1 mini料盘架） Key features（主要功能）：Tighten the filament, when the filament is relatively full（卷紧耗材丝，在耗材丝比较满时） Current Version（当前版本）：1.0.4 (20240410)Update Notes（更新说明）：1.0.4 (20240410)：The spiral structure at the bottom of the inner bushing has been optimized to obtain a more suitable rewinding angle（优化了内轴套底部的螺旋结构，以获得更合适的回卷角度）1.0.3 (20240408)：Fixed a small deviation that did not affect the dimensions on the shaft cover used（修正了一处不影响使用的轴盖上尺寸的小偏差）1.0.2 (20240407)：Modified the bottom of outer bushing and Threaded bushing, and modified the top snap ring size of Claw Bushing and Threaded Bushing to better implement the pause function（修改了外轴套和螺纹套的底部，修改了爪套和螺纹套的顶部卡环尺寸以更好的实现暂停功能）1.0.1 (20240406)：The spacing between the central shaft and the inner bushing has been optimized（优化了中心轴和内轴套之间的间距）1.0.0 (20240405) ： Model publishing（模型发布） Rewind angle（回卷角度）：120°~180° Rewind distance（回卷距离）：depends on the filament thickness（取决于耗材丝厚度） Need for Support（是否需要支撑）：No（不需要） Need for Brim（是否需要边缘）：It has been added by customization, and can be removed if not needed（已定制添加，如不需要可去掉） Need for Non-Printing Accessories（是否需要非打印配件）：None,print-only（不需要，纯打印件） Need multi-colored（是否需要多色）：No, but you can print in parts if you like（否，但可以根据自己喜好分件打印） Number of base kit parts（基础套件零件数量）：12 Filament consumption（耗材消耗量）：120g Base kit Print the number of Plate（基础套件打印分盘数量）：3Slicing software info（切片软件信息）:Bambu Studio 1.9.0 Public beta（Recommended推荐使用）【Since I couldn&#39;t pass the review with the 1.9.0 public beta configuration, I switched back to 1.8.4.51 first】【由于我使用1.9.0 Public beta配置无法过审核，所以先换回1.8.4.51】 Detailed installation instructions（详细的安装说明）：Scroll down the page to see（下滑页面后查看）<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_0325a06261d81.gif"></figure><h3>Special Instructions（特别说明）：</h3>As the version is updated, the appearance of some parts of the model will change accordingly, and the pictures on the page are for reference only.随着版本更新，模型一些部件的外观会随之改变，页面上的图片仅作为参考。The function of this model depends on the friction and resilience of the filament, so there will be some differences in the performance of the model printed with different filaments, the main accessories that determine the rewinding angle are the base cover and the resistance ring, and the experimental model uses PolyLite (logo color) for printing and testing. By default, the 6-blade resistance ring can achieve satisfactory results, and the standard for suitable resistance is that when the shaft bushing is rotated, the resistance ring begins to rotate when the spiral ring of the Inner bushing is basically compressed. If the resistance is too small, you can choose to print the resistance ring of more blades. If the resistance is too high, the resistance blades can be cut to reduce the resistance. The resistance of the newly printed accessories is relatively large, so it is recommended to manually turn it a few times to make it run in to a relatively stable state before starting to use it officially. Finally, it is recommended not to use filament silk screen printing base covers and resistance rings that are too smooth or too brittle (ordinary PLA is fine). 本模型的功能实现依靠耗材丝的摩擦力及回弹力，所以不同耗材打印的模型表现会有一些差异，决定回卷角度的主要配件为基盖和阻力圈，实验模型采用的是PolyLite（标志颜色）进行打印和测试。 默认情况下6叶阻力圈即可实现满意效果，阻力合适的标准表现为转动轴套时，内轴套的螺旋圈基本压缩完全时阻力圈开始转动。 如果阻力过小可以选择打印更多叶片的阻力圈。 如果阻力过大可以剪掉阻力叶片来降低阻力。 新打印的配件阻力相对较大，建议手动转几圈使其磨合到相对稳定的状态后再开始正式使用。 最后建议不要使用过于光滑或者过于脆的耗材丝打印基盖和阻力圈（普通PLA就行）。  <h3>Optional（选装件）：</h3><a target="_blank" href="https://makerworld.com/models/413755#profileId-315791" rel="nofollow noopener">Small Claw bushing 小爪套(43-53mm)</a> Medium Claw bushing 中爪套(53-63mm) - [Included in the Base kit 包含在基础套件中] <a target="_blank" href="https://makerworld.com/models/413755#profileId-315797" rel="nofollow noopener">Large Claw bushing 大爪套(63-80mm)</a> <a target="_blank" href="https://makerworld.com/models/413755#profileId-315800" rel="nofollow noopener">Threaded bushing 螺纹套(43-80mm) </a>- [Supported by the vast majority 支持于绝大多数] 6-blade resistance ring 6叶阻力圈 - [Included in the Base kit 包含在基础套件中] <a target="_blank" href="https://makerworld.com/models/413755#profileId-315804" rel="nofollow noopener">9-blade resistance ring 9叶阻力圈</a> <a target="_blank" href="https://makerworld.com/models/413755#profileId-315810" rel="nofollow noopener">12-blade resistance ring 12叶阻力圈</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_8e90f1414cd7.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_bb97b7c426f64.png"></figure><h3>Problems with use（使用问题）:</h3>Does it have an impact on print quality（是否对打印质量产生影响）:After a period of use and testing, I didn&#39;t find any noticeable effects, at least I didn&#39;t feel it obviously.If you&#39;re concerned about this, you can manually disable the rewind function when printing.经过我一段时间的使用和测试，没有发现有明显的影响，至少我没有明显感觉出来。如果你担心这个，在打印时可以手动停用回卷功能。Will it put a large burden on the extruder（是否会对挤出机带来较大负担）:The tension of the extruder is so strong that it can even break the filaments directly, so this burden on the rewinding spool holder should not be a problem (Moreover, there is also a moment amplification effect of the spool radius), at least in my limited tests.挤出机的拉力是很强大的，甚至能将耗材丝直接拉断，所以回卷架的这点负担应该不成问题（而且还有料盘半径的力矩放大作用存在），至少在我有限的测试中一切都是正常。Disabling the rewind feature（停用回卷功能）： 1.Temporarily deactivated, use your thumb against the shaft cover, and pull the Claw bushing or Threaded bushing outward by 10 mm (Don&#39;t worry about slipping, there is also a layer of protective buckle at this time)    临时停用，用拇指顶住轴盖，将抓套或螺纹套向外拉出10毫米即可（不用担心滑落，此时还有一层保护卡扣存在） 2.If it is out of use for a long time, remove the resistance ring, and it can be used as an ordinary spool holder,At least the filament spool doesn&#39;t wobble    长期停用，拆除掉阻力圈，即可当做普通料盘架使用，至少料盘不会晃来晃去 3.Permanently deactivated, all can be removed    永久停用，全部拆掉即可<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_14196518423e4.png"> Adjust the rewind angle（调节回卷角度）： Adjust the amount of resistance, as described in the special instructions 调整阻力大小即可，见特别说明中的描述 Filament spool installation and replacement（耗材的安装与更换）: In addition, when feeding, you can not push the Claw bushing or threaded bushing to the end, leave a distance of about 10 mm, that is, put it in pause mode, and then push it to the end after the feeding is completed, so that you don&#39;t need to push the filament wire by hand all the time (because there is a rewinding force). 可以直接安装，也可以把爪套或螺纹套取下后安装，另外进料时可以先不把抓套或螺纹套推到底，留10毫米左右距离，即置于暂停模式，等进料完成后再推到底，这样就不需要一直用手推着耗材丝了（因为有回卷力）。Disassemble the central shaft（拆卸中心轴）： Even with a buckle, it can be pulled out with enough force 即便在有搭扣的情况下，用足够大的力量是可以直接拔出<h3>Known issues（已知问题）：</h3>1.There is a certain amount of noise in the use of the rewind function, but I think it is within the acceptable range.    回卷功能使用中会有一定噪音，但我就觉得在可接受范围内。 2.After using the resistance ring for a period of time, the resistance will become smaller to a certain extent, because the grinding is smooth, and the rewinding angle will be reduced.    阻力圈在使用一段时间后阻力会一定程度的变小，因为磨光滑了，回卷角度会缩小。 3.In the case that there are not many filaments left, it is not possible to tighten the filaments completely (because the radius is smaller, the rewinding distance is shorter), but this has no adverse effect.    在耗材丝剩余不多的情况下，无法完全收紧耗材（因为半径小了回卷距离就短了），但这并没有什么不良影响。 4.Claw bushing of various sizes are tight when installed in spool that support the lower limit of size, and require force to be loaded.    各种规格的爪套，安装在其支持尺寸下限的料盘时会比较紧，需要用力才能装入。<h3>Installation instructions（安装说明）：</h3>Special note: Before the installation begins, insert the central shaft into the Inner bushing to test whether the rotation is smooth, if not, dispose of the uneven place or apply vaseline to make the rotation smooth(Note that warping can also cause stuttering when printing the central shaft).特别注意：在安装开始前，请将中心轴插入内轴套中，测试旋转是否顺滑，如果不顺畅请处理掉不平的地方或抹凡士林使之旋转顺滑（特别注意，打印中心轴时翘边也会造成卡顿）。<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_2f51e7da0814c.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_16091fe89d5be.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_df42dd763535.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-12_ed6c8286ebb81.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-12_105e2e90c9d25.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_23ee2c97bdb41.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_50f5dc5d34093.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_3f0a389823e39.png"></figure><h3>Special note: Step 8 needs to be rotated to align the buckle at the bottom!</h3><h3>特别提示：第八步需要通过旋转对齐底部的卡扣!</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000413755/design/2024-04-05_7378ec390e7e1.png"></figure><h3>Other（其他）：</h3>R&amp;D time（研发时间）:three weeks（三周） Model software（模型软件）:Autodesk Fusion Test filament dosage（测试耗材用量）:10kg Test filament types（测试耗材种类）:Bambu PLA Basic, Polymaker PolyLite PLA, BASF PLA Basic, KINGROON PLA, JAYO PLA, Lanbo PLA+, CHG PETG, PXA<h4>---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------</h4>This model is affected by different filaments and printer accuracy, and the final result may not be completely satisfactory to you, but even so, I hope you will enjoy this model,Comments and discussions are welcome. I have some other original models.,If you&#39;re interested, you can also take a look.,It&#39;s better to be able to follow me.,Thank you!(I&#39;m so tired of the documentation~~~) 这个模型受不同耗材丝及打印机精度的影响，最终效果不一定能令你完全满意，但即便如此依然希望你可以喜欢本模型，欢迎评价和讨论。 我还有一些其他的原创模型，有兴趣的话也可以看看，能够关注我就更好了，谢谢！（说明文档写的我好累~~~）&nbsp;Warning: This model is an original design of Noker and should not be used for commercial purposes without authorization.警告：本模型为Noker的原创设计，在未经授权的情况下请勿用于商业用途。&nbsp;Noker&#39;s original designs list（Noker的原创设计列表）：<a target="_blank" href="https://makerworld.com/models/503432" rel="nofollow noopener">Mi Thermohygrometer 2 Magnetic Bracket（小米温湿度计2磁吸支架）</a>- [20240620] ★★★<a target="_blank" href="https://makerworld.com/models/500793" rel="nofollow noopener">Scattered filament holder for AMS lite（AMS lite散料支架）</a>- [20240618] ★★★★<a target="_blank" href="https://makerworld.com/models/494496" rel="nofollow noopener">Scattered filament holder for A1（A1散料支架）</a>- [20240613] ★★★★<a target="_blank" href="https://makerworld.com/models/491928" rel="nofollow noopener">Scattered filament holder for A1 mini（A1 mini散料支架）</a>- [20240611] ★★★★<a target="_blank" href="https://makerworld.com/models/424607" rel="nofollow noopener">Alternative Rotary shaft with Automatic rewinding for AMS lite（自动回卷AMS lite料盘架，可替代原配）</a> - [20240412] ★★★★★<a target="_blank" href="https://makerworld.com/models/416063" rel="nofollow noopener">Rotary spool holder with Automatic rewinding for A1（带自动回卷功能的A1料盘架）</a> - [20240406] ★★★★<a target="_blank" href="https://makerworld.com/models/413755" rel="nofollow noopener">Rotary spool holder with Automatic rewinding for A1 mini（带自动回卷功能的A1 mini料盘架）</a> - [20240405] ★★★★<a target="_blank" href="https://makerworld.com/models/172972" rel="nofollow noopener">A1 / A1 mini fan Cover Guard（部件冷却风扇保护罩）</a> - [20240226] ★★★<a target="_blank" href="https://makerworld.com/models/171024" rel="nofollow noopener">Hamster series - Urine sand shovel（仓鼠系列 - 尿砂铲子）</a> - [20240204] ★<a target="_blank" href="https://makerworld.com/models/116787" rel="nofollow noopener">AMS lite filament spool anti-drop ring（料盘防掉落圈）</a> - [20240101] ★★<a target="_blank" href="https://makerworld.com/models/87466" rel="nofollow noopener">Trouser strap buckle（裤带卡扣）</a> - [20231209] ★<a target="_blank" href="https://makerworld.com/models/75527" rel="nofollow noopener">AMS Lite Large diameter spool adapter（大直径料盘适配器）</a> - [20231127] ★★★★<a target="_blank" href="https://makerworld.com/models/75541" rel="nofollow noopener">A1 &amp; A1 mini Purge poop Cleaner（喷嘴清洁板）</a> - [20231127] ★

P1S

02

01