狗天策用力呀

ChainsawGraphics

More Art as requested by my daughter for her room. Thought Id share incase someone else has a little princess that needs more wall decor. &nbsp;Print at 100% infill with a layer height of 0.04mm with a base layer of 0.16mm You may print at higher layer heights below the Min Depth of 0.48mm The Max Depth is 2.2mm and the Actual Depth is 2.3mmFilaments Used: PLA BambuLab Matte Charcoal Black Transmission Distance: 0.3 PLA Polyterra ArcticTeal Transmission Distance: 0.1 PLA Polyterra Savanah Yellow Transmission Distance: 3.4 PLA BambuLab Matte Scarlett Red Transmission Distance: 1.9 PLA BambuLab Matte Sakura Pink Transmission Distance: 2.3 PLA Polyterra Banana Transmission Distance: 3.8 PLA BambuLab Matte White Transmission Distance: 3.5 This print uses 7 unique filamentsSwap Instructions: Start with Charcoal Black At layer #10 (0.52mm) swap to ArcticTeal At layer #26 (1.16mm) swap to Savanah Yellow At layer #34 (1.48mm) swap to Scarlett Red At layer #36 (1.56mm) swap to Sakura Pink At layer #43 (1.84mm) swap to Banana At layer #49 (2.08mm) swap to White for the rest.

Fluttershy - My little pony hueforge wall decor

小马宝莉

这是文艺小青年

bilibili： BV1Sx4y1i7xR     全网同名&nbsp;可以把头环换成发卡，安装可以有点斜度比较好看些&nbsp;需要磁铁6mmx1.5mm   8个

原神 派蒙头饰 皇冠 装饰 Paimon Project Genshin Impact 원신

口袋妖怪

3DealityDesigns24

This comes in two sets that are pretty self explanatory, It depends on what finish you would like on it in the 3mf file.&nbsp;The wheels i used gorilla glue to stick them on, you can lay the truck on the edge of a table hanging to add them. I also made it a stationary pallet truck as i didn&#39;t want to have to chase it across the table. I also printed it all separate to save time and filament.&nbsp;The handle just pushes into place pretty easy.&nbsp;Try to turn off supports for the bottom pallet I&#39;ve included separate 3mf files for the pallets. You don&#39;t need to add supports to these otherwise it creates a lot of work removing them.&nbsp;&nbsp;We also have a patreon and link tree for our socials below<a target="_blank" href="https://linktr.ee/3dealitydesigns" rel="nofollow noopener">3dealitydesigns | Instagram, TikTok | Linktree</a>

Pallet truck coaster holder with pallet coasters

杯垫

FlorinV

I know there are other racks and holders for paints, but I wanted something a bit different, more flexible and still simple to print, without using more filament than needed.<ul><li>Minimal footprint and filament use, but still very strong. For 28 bottles version with 26mm bottle size: estimated print time 7.6h and 248gr filament.</li><li>Good visibility of bottles and also good grip. (not easy to flip them over)</li><li>Fusion 360 file included, designed to easy change the bottle size and number of columns. (just change 2 parameters; please check the print screens bellow for more info)</li><li>Available profiles and tested for Vallejo bottles: 17ml and 60ml. The hole sizes are: 26mm and 36.8mm. Each profile contains several models with different number of columns. (e.g. 1, 3, 5, 7) Each column has 4 rows.</li><li>Simple to print, without any supports. If you generate other sizes using the fusion file, please arrange the model on the plate similar to how I did it in my profiles. (upside down, as this is how I designed the model and the most efficient way to print them without issues)</li><li>There is no special design to attach different models between them, but you can easily glue them together. So, you can add from time to time another set of columns, as you need them or even glue together different bottle size columns. </li></ul>How to change the bottle size and number of columns, if you need something different than already available in my profiles:<ul><li>open the file in fusion 360 and go to: Modify → Change Parameters (as shown bellow)</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000237584/design/2024-03-08_e9416dcfadd5c.png"></figure><ul><li>Change the size value and/or columns value:</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000237584/design/2024-03-08_c958e077a5969.png"></figure>

Customizable Paint Rack

光固化

NUKDDD

Legend says that some chickens and bunnies had babies and that's where these adorable little hole-y eggs came from. People would go hunt for these eggs every spring, thus came the holiday called Easter…I made that up, it's actual about a bunny waking up after a long nap and losing the race to the tortoise and became an egg.&nbsp;Please give a 👍 if you like it, even if you don’t download it, it’ll help others discover it 😊Commercial rights available for all my designs at <a target="_blank" href="https://www.patreon.com/NUKDDD" rel="nofollow noopener">https://www.patreon.com/NUKDDD</a>&nbsp;These eggs will look great day and night by themselves or next to other decors.&nbsp;<a target="_blank" href="https://shrsl.com/4gf88" rel="nofollow noopener">Designed to fit Bambu Lab's Lamp Kit, available in the online shop.</a>&nbsp;Printed with Bambu's <a target="_blank" href="https://shrsl.com/4gfvl" rel="nofollow noopener">Basic</a> and <a target="_blank" href="https://shrsl.com/4gfae" rel="nofollow noopener">Matte PLA</a>&nbsp;No support, easy assembly, big one compatible with Bambu Lamp Kit 001 and small one for tea lights up to 40mm in diameter. Standard setting, except for the bases, they all have fuzzy skin turned on, default setting. You can support me by using my affiliate link to purchase <a target="_blank" href="https://amzn.to/3PxD8HO" rel="nofollow noopener">the LED candle</a> I purchased in my video and photos. I may earn a small commission.&nbsp;All you need is to bring your own light, nothing else is needed, like most of my designs. Check them out in my profile!&nbsp;Disclaimer: This model is part of the Creator Program, When you purchase the Lamp Kit 001 or filament through the links provided, creators may earn an affiliate commission as a reward of their work. (The creator program is currently in the trial phase. The application is not yet open to public.)

Easter Bunny Egg Lamp 

Evan76

顶部熨烫测试 大字代表熨烫流量 mm代表熨烫速度 不要随便更改切片工艺中的参数。分别有10%-50%的熨烫流量对应的10%-50%的熨烫速度Top ironing test Large characters represent ironing flow mm represents ironing speed Do not change the parameters in the slicing process casually.There are 10%-50% ironing flow rates corresponding to 10%-50% ironing speeds

【顶部熨烫测试】Top ironing test

打印机测试

MikeGTP

Hello Everyone!&nbsp;I designed a new filament shelf. This is for mounting your spools vertically!&nbsp;You can also feed filament to the printer from the spool while in the stand if you use the rollers&nbsp;This shelving system is customizable&nbsp;You can stack them a few high, align them in single stacks, or a combination of the two!&nbsp;There are no extra hardware parts needed. Everything is 3d Printed!&nbsp;If you store your spools in dry bags, most of those will also fit!&nbsp;You may chose to add double sided tape to the very bottom if if will go onto a slick surface. There are a lot of possibilities to customize it for your needs!&nbsp;There is a 3mf for each set of parts. There are no supports needed. I did use a 15mm brim for the square and round frame pegs and i slowed the speed for those done a good bit.&nbsp;UPDATE: I added rollers for the spool. If you want to use them, just slide one over each spool peg during assembly. This will allow you to feed filament from the spool directly into your printer&nbsp;I didn't use any glue when assembling this, but it would not be a bad idea to use a drop of glue in each hole for added support. That being said, the pegs do fit in snug. Not everyone's printer is tuned and calibrated the same. If the peg doesn't go in easy for you, try rotating or rocking the piece in.&nbsp;If this works out great for you, don't forget to share your photos in the review and on Facebook!&nbsp;ENJOY!&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_3dc9131d7c641.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_40711b8d5520e.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_d777416e582d8.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_e1140b03a371b.jpg"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_a90272b0cbbbc.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_427c859ac5d3.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_fe1c3c8888f54.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_4effb9e84098d.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_6a367169f376b.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_5132f154c05e9.jpg"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_e600aff044e7f.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_d26a0956d9096.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/482343/2024-01-31_decac15c57991.jpg"></figure>&nbsp;

Vertical Filament Shelf With Rollers Customizable! ALL 3D PRINTED!

打印机配件

fay3dlab

So i just got myself the LED lamp kit and was looking for a cool lamp shades to print for it.. then i came across someone making a incubator like cylinder with an alien in the middle using resin.. i thought it was a great idea.. and so i design one for myself.. but of cause i want to make a suspended version of it.. Then i remembered finding a baby raptor model on makerworld.. it was made for resin printing.. so i low-poly the raptor and added the baby raptor blue and turned it into a suspended model.. i had to split the raptor in 2 and added supports to the hanging hands.. legs and tail.. so it might look weird if you look closely..&nbsp;<figure class="table"><table><tbody><tr><td>:UPDATE: it turns out that the user who shared the raptor model on makerworld is not the owner of the 3D model.. he shared the file without authorization.. The owner reached out to me and told me what the user had done.. the owner of the 3d model is <a target="_blank" href="https://www.turbosquid.com/Search/Artists/wofle" rel="nofollow noopener">wofle</a> from turbosquid.com.. and he gave me permission to share my remixed version of the raptor as long i dont sell it commercially.. so thank you Mr Wolfe for sponsoring your awesome raptor model for my suspended models..</td></tr></tbody></table></figure> i modelled the incubator using Tinkercad and added the LED kit on the bottom.. so the LED light would shine through the bottom grill of the incubator cylinder and light the suspended baby raptor in the middle..<img src="https://makerworld.bblmw.com/makerworld/draft/681411/2023-12-15_2b30871ab39c9.gif"> If you have an AMS i recommend printing some of the incubator parts with transparent filament like i did for the bottom base.. so that the LED would shine through it and make it more cool.. in my opinion.. Assembly is fairly simple.. you just need to be careful when adding the square peg into the raptor's body.. it should fit loosely.. the peg is just used to hold the 2 half of the raptor aligned.. the bottom parts should fit tight.. and the top slightly loose.. the base where you insert the LED kit should fit loosely to the middle base.. so that you can turn your raptor to whichever position you'd like without the wires in the way..  <blockquote>If you're thinking of buying the LED kit.. please do support me by using my affliate link here.. <a target="_blank" href="https://shrsl.com/4g18i" rel="nofollow noopener">LED LAMP KIT 001</a> every little things helps me out..</blockquote><figure class="table" style="height:162.344px;width:960px;"><table style="background-color:rgb(255, 255, 255);border:1px double rgb(179, 179, 179);"><tbody><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;">If you would like to support me, you can join me on my <a target="_blank" href="https://www.buymeacoffee.com/fay3dlab" rel="nofollow noopener">buymeacoffee</a> page..</td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;">By joining me as a supporter.. you'll be able to get behind the scenes informationon my current projects as well as future projects..</td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;">And if you're looking to sell my prints.. you can join my merchant membership tier as lowas USD10 a month..</td></tr></tbody></table></figure>

Suspended Baby Raptor Incubator LED Lamp

Denver3D

The Melpaca Pal from the Palworld game in high resolution!Each part (ears, legs, horns, etc) is separated in the file for easier multimaterial printing, but it can also be easily printed all in the same filament if you plan on painting afterwards.

Melpaca from Palworld

帕鲁

水世界水族馆gokumine

pokemon cubone AMS口袋妖怪宝可梦宠物小精灵卡拉卡拉AMS4色打印

pokemon cubone AMS口袋妖怪宝可梦宠物小精灵卡拉卡拉AMS4色打印

3D servis

The stand is able to tilt according to your needsEasy print without supports nor glueTested with PLA and PETG&nbsp;If you have problem with print of worm, you can print profile worm - 2 parts.  It's without glue, only connect together with nuts&nbsp;Added bottom part with lower “horns”<img src="https://media.printables.com/media/prints/734305/rich_content/d1cc0fb7-688a-4ff4-a083-0ce6453751c8/thumbs/cover/800x488/png/snimek-obrazovky-2024-02-21-v-155507.webp">&nbsp;Upload new version for ipad (tablet) <a target="_blank" href="https://makerworld.com/en/models/216325" rel="nofollow noopener">https://makerworld.com/en/models/216325</a><img src="https://makerworld.bblmw.com/makerworld/draft/615791/2024-03-01_48bd1d4c76084.jpeg">&nbsp;

小马宝莉

口袋妖怪

杯垫

光固化

灯

打印机测试

打印机配件

玩

帕鲁

口袋妖怪

无