Skill Billy

peteb

Print face down, there are 2x 8mm x 2mm magnet holes on the back. &nbsp;I put magnets in the holes and place a couple screws in the wall and the magnets hold it up.

Bigfoot wall art

Wall Art

PrintedByJohn

This print is very flexible and fun to play with.

Multi color NASA chainmail 

NASA Fabrix

trynottobreakanything

This is the Gear Rhombo Junior (Jr.) (the Spirit of Mini Gear Sphere). This is totally redesigned from the Gear Sphere by TNTBA. This Gear fidget toy is a lot of fun and is now portable.Approximate size of this design is: 50mmx50mmx50mm.&nbsp;This is the Free version of the <a target="_blank" href="https://thangs.com/designer/trynottobreakanything/3d-model/Gear%20Rhombo%20JR%20by%20TNTBA-1087166" rel="nofollow noopener">Gear Rhombo JR which I&#39;ve licensed for those who wish to sell and print.</a> &nbsp;The time to print and fully assemble is approximately 1 hour and 15-30 minutes.&nbsp;Gears and core may be printed in any material. Clips were designed to be printed in PETG. Tool can be printed in PLA.&nbsp;Place the clip into the tool and use the tool to place the clips directly into the holes on the core. Make sure you go directly into the hole to avoid splitting, breaking, or over-bending the clips. I would recommend that you print out additional clips to ensure you have extras when you mess up.&nbsp;Once the clips are installed, you can place the gears following the numbering located on each gear and core side.&nbsp;The mechanism to move this toy fidget was inspired by <a target="_blank" href="https://thangs.com/designer/RuvenBals/3d-model/Gear%20Ball-1069853" rel="nofollow noopener">RuvenBals&#39; Gear Ball </a>and <a target="_blank" href="https://www.thingiverse.com/thing:10483" rel="nofollow noopener">Emmett&#39;s Gear Cube</a>.&nbsp;Enjoy!

Gear Rhombo JR by TNTBA (Free Version)

Gear

user_3840935634

I love uhltimate&#39;s OTF Fidget Knife concept but thought the blade looked a bit boring, so I fiddled with it (guided version) to add a sharper-looking knife tip. Pictured here with LucasAlexander&#39;s excellent Ergonomic slider remix, which I highly recommend for ease of fidgeting: <a target="_blank" href="https://makerworld.com/en/models/473585#profileId-383724" rel="nofollow noopener">https://makerworld.com/en/models/473585#profileId-383724</a>&nbsp;I recommend 100% infill and printed in PETG to maximize sturdiness. Do be careful however: even though it&#39;s a toy it can still be dangerous given its shape!

Sharper Blade for uhltimate's OTF Fidget Knife

knives

joshua.makes

Hey Futurama fans and DIY enthusiasts! Get ready to indulge in the futuristic refreshment of Slurm with this Slurm Can Lightbox project. Featuring the iconic beverage from the hit TV show, this lightbox is a quirky and fun addition to any space, perfect for fans of the quirky and irreverent humor of Futurama.&nbsp;Here's What's Included:&nbsp;Iconic Can Design: The centerpiece of this lightbox is the instantly recognizable Slurm can, complete with its vibrant green color and distinctive logo, just like in the show.&nbsp;Print-Ready Files: We provide you with the 3D printing files needed to create your own Slurm Can Lightbox, ensuring a smooth and hassle-free crafting experience.&nbsp;Simple Assembly: Worried about putting it together? Don't worry; it's easier than you think! We've included links to where we purchase our LED strips. Simply peel and apply.&nbsp;Personalize Your Beverage Break: Customize your project by choosing your preferred colors and finishes. Whether you want to capture the retro-futuristic vibe of Futurama or add your own creative flair, the choice is yours.&nbsp;Quirky Charm: When illuminated, this Slurm Can Lightbox adds a playful and whimsical touch to any room, transporting you to the futuristic world of New New York and the hilariously bizarre adventures of the Planet Express crew.&nbsp;Share the Laughs: Display your finished creation proudly and share a laugh with friends, family, and fellow Futurama fans. It's a conversation starter and a symbol of your love for the cult classic TV show.&nbsp;Whether you're a die-hard fan of Futurama or just appreciate its unique brand of humor, this DIY project is a fun and entertaining way to showcase your love for the series. Create your own Slurm Can Lightbox and let the refreshing taste of the future brighten up your space!&nbsp;⚡ USB LED:<a target="_blank" href="https://amzn.to/3S4VnVE" rel="nofollow noopener"> https://amzn.to/3S4VnVE</a>&nbsp;or&nbsp;⚡ USB LED w/ Switch:<a target="_blank" href="https://amzn.to/3RYEImp" rel="nofollow noopener"> https://amzn.to/3RYEImp</a>&nbsp;or&nbsp;⚡ USB LED w/ Remote:<a target="_blank" href="https://amzn.to/3vs7Uuo" rel="nofollow noopener"> https://amzn.to/3vs7Uuo</a>&nbsp;*If you purchase an item through the links provided, I may receive a commission. This helps support my work and enables me to continue providing valuable content. Thank you for your support!*

Futurama Slurm Can USB LED Lightbox

Light Boxes

crabstiks

Hellraiser box of lament movie prop.&nbsp;The box measures 55mm on each side (about 2.16 ") the same size as a standard rubics cube. There's also now an upscaled by 150% version, this needs to print on 2 plates. Many thanks to Nick C for the suggestion and for doing the test print. &nbsp;There are 2 print profiles of this model, one without a pause, one with a pause to add 1X 8mm diameter by 10mm deep magnet. There is space for 2 magnets but please only add one as the weight of the second magnet can make it a tad heavy to stick properly.&nbsp;The model is made so it clicks together this can mean when it's a fresh print it can feel a little stiff at first.&nbsp;I do recomend using a little ca glue when assembing the four side faces, the panels do clip on but the glue will hold it together much better. It's a good ides the lay the faces out one at a time and checking the orientation before gluing.

Hellraiser Box of Lament movie prop fridge magnet

Lament Configuration 

Jacklove

Joining the MakerWorld family for the first time, I am very happy to share my first model with everyone. I hope you like it and can also provide your opinions or suggestions on this model for my future improvement.

Balloon dog

IanCantDraw

Another wedge to lift the top glass of your Bambu printer when you need to vent for long prints.This one firmly holds the glass top in place, is quick/easy to put on and take off, and doesn&#39;t require assembly or supports.&nbsp;Lots of detail below, but the summary is that this clips onto the glass, then slides over around the handle, creating a firm grip that holds the glass up ~20mm (~¾&#34;), creating a vent.&nbsp;It can clip onto the door handle when not in use (an accidental perk - thank you to the reviewers who discovered this!).&nbsp;&nbsp;Updated 2024-03-6 - The model has been updated and split into Tight Fit and Loose Fit versions.- Tight Fit is very close to the same as the original design. This fits snugly around the glass and the handle.- Loose Fit has larger tolerances around the glass and the handle.Both versions were adjusted to avoid getting stuck on the screws on the bottom of the handle.&nbsp;There are 2 new profiles, accordingly named Tight Fit and Loose Fit.Each new profile has 4 different designs inside, 1 per plate. The designs are simply visual differences and are up to your preference. Just pick your favorite design and print that single plate.Because multiple choices are bundled together, the filament usage and time estimates are wrong. The actual time and usage are about ¼ of those listed.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000158585/design/2024-03-06_cd743bb241775.png"></figure>&nbsp;I&#39;ll keep the old profiles with the old models, but will label them as old.&nbsp;&nbsp;&nbsp;How To&nbsp;- Lift the glass up- Clip the lifter on to the front of the glass to the right of the handle- Push it all the way forward- Slide it left until it stops against the handle (it&#39;s an intentionally snug fit)- Lower the glass back down <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000158585/design/2024-02-09_37e684647c281.png">&nbsp;&nbsp;“Locked” in place:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000158585/design/2024-03-06_f71dc534706c1.png">&nbsp;Recommended Print Settings&nbsp;- Layer height: 0.20mm Standard- Wall loops: 3- Infill: 15%, Cubic&nbsp;If printed standing on its right side, it shouldn&#39;t need supports or a brim (see pictures). The model should already be in this orientation when opening it.This printed well and feels very sturdy in both Bambu PLA Basic and Sunlu PLA.&nbsp;&nbsp;&nbsp;I&#39;m open to feedback. Feel free to remix, but not sell.&nbsp;&nbsp;&nbsp;Update History&nbsp;2024 -03-06:<ul><li>Adjusted width of the “screw channel” on the bottom lip to prevent the glass handle&#39;s screws from being in the way</li><li>Added Tight Fit and Loose Fit options for those running into issues with the fit being too tight</li><li>Changed numbers &amp; arrows on top to engraved instead of embossed</li><li>Reworked and cleaned up the original CAD design</li><li>Minor visual changes</li></ul>&nbsp;2024-02-11:<ul><li>Added a version that includes a grip and uploaded 2 profiles for it (center hole and solid).</li><li>Made a minor change to the existing models to smooth out a sharp corner (no functional changes), and updated profiles.</li><li>Updated photos and description.</li></ul>2024-02-03:<ul><li>Description &amp; picture revisions.</li><li>No model changes.</li></ul>2024-01-28:<ul><li>Replaced the STLs with higher quality exports from the CAD software and updated the print profiles with them.</li><li>There&#39;s no change to the design or functional geometry, but the curves look cleaner now.</li></ul>2024-01-27:<ul><li>Initial upload.</li></ul>

Sturdy Glass Lifter for X1/P1

P1S MODS

Lucky 13 Toys

<h3>Dummy 13 is now on a CC BY 4.0 license!</h3>This means that you are free to share these files however you like, including selling prints, provided that you give proper attribution. You can give proper attribution by including this notice on your product page:<figure class="table"><table><tbody><tr><td><a target="_blank" href="https://makerworld.com/en/models/183780#profileId-202639" rel="nofollow noopener">DUMMY 13 Printable Jointed Figure </a>© 2023 by <a target="_blank" href="https://www.lucky13toys.com/" rel="nofollow noopener">Lucky 13 Toys </a>is licensed under <a target="_blank" href="http://creativecommons.org/licenses/by/4.0/?ref=chooser-v1" rel="nofollow noopener">CC BY 4.0 </a></td></tr></tbody></table></figure>Please help me build my identity as a creator by referring to this design by its original name. Don't pass off my work as your own product. Too many people are doing that already!&nbsp;Want to support future projects with a one-time donation? <a target="_blank" href="https://www.paypal.com/donate/?business=65FUQ2SJMYDDS&no_recurring=0&item_name=Thanks+for+supporting+Lucky+13%21&currency_code=USD" rel="nofollow noopener">Make a PayPal donation here!</a>&nbsp;&nbsp;&nbsp;<a target="_blank" href="https://www.printables.com/@soozafone/activity/4153" rel="nofollow noopener">This is my own work, originally uploaded to Printables.</a>&nbsp;Yes, Dummy 13 is now on MakerWorld.&nbsp;<h3>Please read before printing:</h3>This is a work in progress. It has been collecting virtual dust while I work on other projects, so I've decided to release it now in a “beta” state. I don't have a timeline for when the final version will be finished, but the current files are fairly complete - just lacking some perfectionist polish. Please understand that there is some room for improvement here. I welcome your feedback to help make this design the best it can be.&nbsp;What's finished right now: Design of all parts, except for minor tweaks based on feedback. Basic instructions.&nbsp;What's not finished: Parts on runners for better adhesion without brims. More detailed instructions. Fusion 360 and STEP files for Printables Club members (please note that these will not be available until the design is finalized). Any updates based on feedback.&nbsp;Can I sell it? Yes, Dummy 13 is distributed under a CC BY 4.0 license that does allow commercial use, provided that you provide proper attribution.&nbsp;If you'd like to say thanks and help support future development, you can make a one-time donation <a target="_blank" href="https://www.paypal.com/donate/?business=65FUQ2SJMYDDS&no_recurring=0&item_name=Thanks+for+supporting+Lucky+13%21&currency_code=USD" rel="nofollow noopener">here</a> :)&nbsp;---&nbsp;<h3>Introducing Dummy 13!</h3>(…working title.)This is another variant on <a target="_blank" href="https://www.printables.com/model/148367-lucky-13-printable-jointed-figure" rel="nofollow noopener">Lucky 13</a>, and I actually started designing it before <a target="_blank" href="https://www.printables.com/model/422353-mini-13-printable-jointed-figure" rel="nofollow noopener">Mini 13</a> or <a target="_blank" href="https://www.printables.com/model/555170-easy-13-printable-jointed-figure" rel="nofollow noopener">Easy 13</a>. As you can probably tell, my goal here was to bring some more humanlike proportions to the figure, while also improving the way everything fits together.&nbsp;My hope is that this will be an easier print than the original Lucky 13, though still a step up from Mini and Easy.&nbsp;<h3>Printing</h3>As with the original, Dummy 13 is made up of an inner "frame" with a layer of “armor” over top. You can use the material of your choice for the armor, but you should print the frame with a strong and sturdy material like ABS, ASA, or PETG. I mostly use ASA.&nbsp;PLA is not recommended for the frame. If you print the frame in PLA and complain that it broke or went floppy, I'm going to be like, “yeah dude, I told you not to.”&nbsp;All parts print without supports and you should not need to reorient anything. Bed adhesion is the toughest part of this print. For better adhesion try slowing down your first layer, printing external perimeters first, and adding a brim if needed. Use 0.15mm layers (0.2mm first layer).&nbsp;You can use the included 3MF files with pre-plated parts, or arrange the individual parts yourself. If a part starts with “2x” or “4x,” print that many copies. There are also a couple extra bits (a simple staff accessory and an adapter for the <a target="_blank" href="https://www.printables.com/model/563861-lucky-13-display-base-20" rel="nofollow noopener">display base</a>) that are included separately.&nbsp;Recommended print settings (100% scale, 0.4mm nozzle)<figure class="table"><table><tbody><tr><td rowspan="2">Material</td><td>Frame parts</td><td>ABS, ASA, or PETG</td></tr><tr><td>Armor parts</td><td>Any</td></tr><tr><td rowspan="2">Layer height</td><td>First layer</td><td>0.2 mm</td></tr><tr><td>Other layers</td><td>0.15 mm</td></tr><tr><td colspan="2">Infill</td><td>20% rectilinear</td></tr><tr><td colspan="2">First layer speed</td><td>25% of default</td></tr><tr><td colspan="2">Elephant foot compensation</td><td>0.15 mm</td></tr><tr><td colspan="2">Supports</td><td>None</td></tr><tr><td colspan="2">Brim</td><td>As needed (depends on bed adhesion)</td></tr><tr><td colspan="2">Additional settings</td><td>☑ Print external perimeters first</td></tr></tbody></table></figure>&nbsp;<h3>Assembly</h3>Follow this video for assembly instructions. Pay attention - some parts look very similar!<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=Rwu3UP0cHZw"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/Rwu3UP0cHZw" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;<h3>Customizing</h3>Dummy 13 should be compatible with most handheld accessories made for my other designs. Check out Lucky 13's <a target="_blank" href="https://www.printables.com/model/148367-lucky-13-printable-jointed-figure/remixes" rel="nofollow noopener">remixes page</a> for a good starting point!&nbsp;&nbsp;This design has already been stolen and stripped of attribution a hundred times over. Please don't add to that.

DUMMY 13 Printable Jointed Figure (beta files)

Dummy 13

wannes.garrevoet

A 3D printable Paint Mixing Attachment, a versatile tool compatible with drills or accu-screwdrivers. Designed for effortless blending of paints, primers, and stains, its ergonomic design ensures easy handling while its robust construction promises durability. Say goodbye to manual stirring and hello to efficient, professional-grade mixing with our innovative attachment.

Paint mixer

tools

McFly

I love mini spools! I dont use much colors, mostly black and white prints. So buying a 1kg color spool seems like too much for me. I found Eryone mini spools, with 200g of filament for about 6-7€ vs 18-30€ of a 1kg spool.Yes, the price per kg is more expensive, but for the price of 1 spool, I can have 4 different colors!&nbsp;The problem, this mini spools dont fit in the AMS, so I can't print multicolor/multimaterial :(&nbsp;Ive made an adapter that will securely fit your mini spool in your AMS.&nbsp;Eryone 200g mini spools are 139mm diameter, 56mm hole and 35mm wide. This adapter may accommodate other mini spools, but I didn't test them. If you try let me know so I update the description.&nbsp;Enjoy! :)&nbsp;PS: if you have AMS riser by maCyo42, here is a remix for his spool holder that can be used with mini spools. In the original version the mini spools wont fit. https://makerworld.com/en/models/216328

Eryone 200g mini spool adapter

Spool Adapter

Maple3DPrinting

Print this support free Nightstand Organizer to keep all your daily objects in one convenient place!