Mario4583

Gridfinety

CopyKnight

With the introduction of the Air-Stream-Freezer, our team set itself the task of developing a model for the Bambulab X series. The biggest challenge was to make it LIDAR compatible. Our team rose to this challenge, further developed the Air-Stream-Freezer and quickly designed the Air-Stream-Turbine. Once again, I would like to thank the entire team, who have once again invested every spare minute for months in the development of the project. Once again, it has been designed, designed, changed and tested. A special thank you to Paul, to whom we tirelessly handed over new designs so that he could check compatibility. Once again, it is expressly stated that remixes of this product design are completely prohibited, as once again no phase or rounding off has been added more than necessary. To ensure that there is something for everyone&#39;s taste, this time there are of course two more versions available in addition to the 7 well-known ones: Firstly, the original: 1: Air-Stream-Turbine (it wasn&#39;t called that for no reason) <a target="_blank" href="https://makerworld.com/en/models/429489#profileId-333824" rel="nofollow noopener">https://makerworld.com/en/models/429489#profileId-333824</a> 2: Bambu Lab logo with lettering <a target="_blank" href="https://makerworld.com/en/models/429475#profileId-333807" rel="nofollow noopener">https://makerworld.com/en/models/429475#profileId-333807</a> 3: Bambu Lab lettering single <a target="_blank" href="https://makerworld.com/en/models/429500#profileId-333837" rel="nofollow noopener">https://makerworld.com/en/models/429500#profileId-333837</a>  4: Bambu Lab logo single <a target="_blank" href="https://makerworld.com/en/models/429494#profileId-333828" rel="nofollow noopener">https://makerworld.com/en/models/429494#profileId-333828</a> 5: Bambu Lab P1S version <a target="_blank" href="https://makerworld.com/en/models/429485#profileId-333817" rel="nofollow noopener">https://makerworld.com/en/models/429485#profileId-333817</a> 6: Bambu Lab P1P version <a target="_blank" href="https://makerworld.com/en/models/429480#profileId-333812" rel="nofollow noopener">https://makerworld.com/en/models/429480#profileId-333812</a> 7: completely without bells and whistles, branding or logo <a target="_blank" href="https://makerworld.com/en/models/429474#profileId-333806" rel="nofollow noopener">https://makerworld.com/en/models/429474#profileId-333806</a> Newly added: 8: Bambu Lab X1C version <a target="_blank" href="https://makerworld.com/en/models/429482#profileId-333814" rel="nofollow noopener">https://makerworld.com/en/models/429482#profileId-333814</a> 9: Bambu Lab X1E version <a target="_blank" href="https://makerworld.com/en/models/429486#profileId-333819" rel="nofollow noopener">https://makerworld.com/en/models/429486#profileId-333819</a> What&#39;s new in this version: The Air-Stream turbine can now be printed completely unsupported. There is a split inlet and an asymmetrical outlet for the air supply. Due to the asymmetrical outlet, it is only possible to speak of 360 degrees in relative terms, which is why we have omitted the degree sign in our illustration and replaced it with an asterisk. In case of doubt, this model can be printed with only two walls and completely without infill with a 0.2 layer height. However, we recommend 3 walls with 10% infill and a layer height of 0.1, or 4 walls and 10% infill with a 0.2 nozzle. For all variants, a corresponding number of upper layers should be ensured. This means 5 layers with 0.2 and 10 layers with 0.1 layer height. The magnets that must be used are the same size as those used in the original Bambu Lab component. (4x2 &amp; 2x2) For design reasons it was not possible to use larger magnets. At the point where the smaller magnet has to be placed, care must be taken when slicing that &#34;recognize thin walls&#34; is selected, as the wall thickness at this point is very small. However, this does not matter, the magnet can still be glued in cleanly without any problems and will hold. With a 0.2 Nozzle there is no problem at all, which is why the High Quality and Ultra pressure profile is specially designed for a 0.2 Nozzle.  It is generally known that the subject of component cooling is viewed with a great deal of skepticism and suspicion. Many people always want proof. But how and with what could you prove something if the evidence proves nothing, because it cannot prove anything, as it could just as well be manipulated? Then there are always many theoretical things that could possibly prove something, but theory and practice are worlds apart. That&#39;s why we won&#39;t try to convince anyone here. Everyone has to convince themselves. We simply want to invite everyone to do a little mini-experiment that they can understand for themselves. Place a glass filled with water under the original fan and everyone will be able to see the same result with their own eyes. The largest bulge in the water surface will not be in the middle under the nozzle, although this is where it would make the most sense in principle. The bulging of the water surface of the Air-Stream turbine, on the other hand, is much more centrally located under the nozzle. Again, these are facts that anyone can see for themselves if they are willing to carry out this simple test. Because let&#39;s not kid ourselves, pictures of a comparison of two 4-sided overhang tests do not seem to be credible enough, which is why we are sparing ourselves a direct comparison this time. Last but not least, it should be noted that the component should only be printed by someone who can dismantle the original and assemble the reprinted one without help. We will not provide any help in this regard, nor will we encourage anyone to possibly destroy the front housing assembly of the printer. Or to put it another way, you dismantle at your own risk. One last point should be mentioned. This model can also be printed without infill and completely without support. Neither the model nor one of the four printing profiles can be held responsible in the event that it should become detached from the build plate during printing. We decided to add a GIF of a print (High Quality and Ultra print profile) to prove that with a clean build plate and well calibrated ABS filament it is possible to print successfully without support and without brim. For anyone else who may have difficulties, a brim could be added. However, this should not be an argument for rating the model or print profile poorly.  What is the difference between the print profiles? Fast Print: Nozzle 0.4 - layer height 0.2 - first layer 0.2 - walls 2 - infill 0 % Medium: Nozzle 0.4 - layer height 0.1 - first layer 0.2 - walls 3 - infill 10 % Gyroid High Quality: Nozzle 0.2 - layer height 0.1 - first layer 0.2 - walls 4 - infill 0 % Ultra: Nozzle 0.2 - layer height 0.1 - first layer 0.2 - walls 4 - infill 10 % Gyroid Thank you and have fun.        Mit der Einführung des Air-Stream-Freezer hat sich unser Team es zur Aufgabe gemacht, ein Modell für die Bambulab X-Serie zu entwickeln. Die größte Herausforderung dabei war es, diesen LIDAR kompatibel zu designen. Dieser Herausforderung hat sich unser Team gestellt, den Air-Stream-Freezer weiterentwickelt und kurzer Hand die Air-Stream-Turbine konzipiert.  Auch heute möchte ich mich abermals bei dem gesamten Team bedanken, das abermals wieder jede freie Minute seit Monaten in die Entwicklung des Projektes investiert hat. Es wurde wieder erneut entworfen, designed, geändert und getestet. An Paul gibt es ein besonderes Dankeschön, den wir unermüdlich neue Entwürfe übergaben, damit er die Kompatibilität überprüfen konnte.  Einmal mehr wird hiermit noch einmal Ausdrücklich erklärt, das Remixe von diesem Produktdesign vollständig untersagt sind, da auch hier wieder keine Phase oder Abrundung mehr als nötig hinein konstruiert wurde. Damit auch diesmal wieder etwas für jedermanns Geschmack dabei ist, stehen diesmal zu den 7 altbekannten natürlich zwei weitere Versionen zu Verfügung:  Zum einen das Original:  1: Air-Stream-Turbine (der wurde nicht ohne Grund so genannt) <a target="_blank" href="https://makerworld.com/en/models/429489#profileId-333824" rel="nofollow noopener">https://makerworld.com/en/models/429489#profileId-333824</a>2: Bambu Lab Logo mit Schriftzug <a target="_blank" href="https://makerworld.com/en/models/429475#profileId-333807" rel="nofollow noopener">https://makerworld.com/en/models/429475#profileId-333807</a>3: Bambu Lab Schriftzug einzeln <a target="_blank" href="https://makerworld.com/en/models/429500#profileId-333837" rel="nofollow noopener">https://makerworld.com/en/models/429500#profileId-333837</a>4: Bambu Lab Logo einzeln <a target="_blank" href="https://makerworld.com/en/models/429494#profileId-333828" rel="nofollow noopener">https://makerworld.com/en/models/429494#profileId-333828</a>5: Bambu Lab P1S Version <a target="_blank" href="https://makerworld.com/en/models/429485#profileId-333817" rel="nofollow noopener">https://makerworld.com/en/models/429485#profileId-333817</a>6: Bambu Lab P1P Version <a target="_blank" href="https://makerworld.com/en/models/429480#profileId-333812" rel="nofollow noopener">https://makerworld.com/en/models/429480#profileId-333812</a>7: komplett ohne Schnickschnack, Branding oder Logo <a target="_blank" href="https://makerworld.com/en/models/429474#profileId-333806" rel="nofollow noopener">https://makerworld.com/en/models/429474#profileId-333806</a>  Neu dazugekommen ist:  8: Bambu Lab X1C Version <a target="_blank" href="https://makerworld.com/en/models/429482#profileId-333814" rel="nofollow noopener">https://makerworld.com/en/models/429482#profileId-333814</a>9: Bambu Lab X1E Version <a target="_blank" href="https://makerworld.com/en/models/429486#profileId-333819" rel="nofollow noopener">https://makerworld.com/en/models/429486#profileId-333819</a>  Was ist neu an dieser Version:  Die Air-Stream-Turbine kann nun komplett ohne Unterstützung gedruckt werden. Es gibt einen geteilten Einlass und einen asymmetrischen Auslass für die Luftzufuhr. Durch den asymmetrischen Auslass kann nur relativ von 360 Grad gesprochen werden, weshalb wir anstelle des Grad Zeichens in unserer Abbildung abgesehen und dies mit einem Sternchen ersetzt haben.Dieses Modell kann im Zweifelsfall mit nur zwei Wänden und komplett ohne Füllung mit einer 0.2 Schichthöhe gedruckt werden. Empfohlen wird allerdings 3 Wände mit 10% Füllung und einer Schichthöhe von 0.1, bzw. mit einer 0.2 Düse 4 Wände und 10% Füllung. Bei allen Varianten sollte auf entsprechend viel obere Schichten geachtet werden. Das heißt 5 Schichten bei 0.2 und 10 Schichten bei 0.1 Schichthöhe. Die Magneten die benutzt werden müssen, haben die selbe Größe wie die, die beim Original Bauteil von Bambu Lab verwendet wurden. (4x2 &amp; 2x2) Konstruktionstechnisch war es nicht anderes möglich größere zu verwenden. An der Stelle wo der kleiner Magnet platziert werden muss, muss beim Slicen darauf geachtet werden, dass „dünne Wände erkennen“ ausgewählt wird, da die Wandstärke an dieser Stelle sehr gering ist. Dies macht aber nichts, der Magnet kann trotzdem ohne Probleme sauber darin eingeklebt werden und wird halten. Mit einer 0.2 Nozzle gibt es dahingehend überhaupt keine Problem, weshalb das High Quality und Ultra Druckprofil speziell für eine 0.2 Nozzle ausgelegt ist.  Im allgemeinen ist bekannt, dass das Thema Bauteilkühlung mit viel Skepsis und Argwohn beäugt wird. Viele wollen immer Beweise. Aber wie und womit könnte man denn etwas beweisen, wenn die Beweise nichts beweisen, weil sie nichts beweisen können, da sie ebenso gut manipuliert sein können? Dann gibt es immer viele theoretische Dinge die womöglich etwas beweisen können, doch zwischen Theorie und Praxis liegen bekanntlich ja auch Welten. Deswegen werden wir hier auch nicht versuchen irgendjemanden zu überzeugen. Überzeugen muss sich schon jeder selbst. Wir wollen lediglich jeden einladen ein kleines für jeden selbst nachvollziehbares Miniexperiment zu machen. Stellt ein Glas mit Wasser gefüllt unter den Originallüfter und jeder wird dasselbe Ergebnis mit seinen eignen Augen wahrnehmen können. Die größte Ausbeulung der Wasseroberfläche wird nicht mittig unter der Nozzle sein, wo es prinzipiell allerdings am sinnvollsten wäre. Die Ausbeulung der Wasseroberfläche der Air-Stream-Turbine hingegen ist wesentlich mittiger und zentraler unter der Nozzle wiederzufinden. Das sind wiederum Tatsachen von denen sich jeder selbst überzeugen kann, sofern er gewillt ist, diesen einfachen Test zu machen. Denn machen wir uns nichts vor, Bilder von einem Vergleich zweier 4 Seiten-Überhangtests scheinen, so wir wir feststellten, nicht glaubwürdig genug zu sein, weshalb wir uns diesmal einen direkten Vergleich ersparen.  Zu guter Letzt sei noch darauf hingewiesen, dass das Bauteil nur jemand drucken sollte, der auch ohne Hilfe, den Originalen demontieren und den neu Gedruckten montieren kann. Es wird von uns dahin gehend keinerlei Hilfe geben, noch werden wir jemanden dazu zu animieren, womöglich die vordere Gehäusebaugruppe des Druckers zu zerstören. Oder nochmal anders ausgedrückt, sie demontieren auf eigene Gefahr. Ein allerletzter Punkt sei noch erwähnt. Dieses Modell kann auch ohne Infill und komplett ohne Unterstützung gedruckt werden. Weder das Modell noch eins der vier Druckprofile kann etwas dafür, für den Fall dass es sich während des Druckes von der Bauplatte womöglich lösen sollte. Wir haben uns entschieden extra eine GIF von einem Druck (High Quality und Ultra Druckprofil) hinzuzufügen, um zu belegen, dass es mit einer sauberen Bauplatte und gut kalibrierten ABS Filament problemlos möglich ist ohne Unterstützung und ohne Brim erfolgreich zu drucken. Für alle anderen, die womöglich Schwierigkeiten bekommen sollten, könnten ein Brim hinzufügen. Allerdings sollte dies keine Argument dafür sein, das Modell oder Druckprofil schlecht zu bewerten.  Worin unterscheiden sich die Druckprofile?  Fast Print: Düse 0.4 – Schichthöhe 0.2 – erste Schicht 0.2 – Wände 2 – Füllung 0 %Medium: Düse 0.4 – Schichthöhe 0.1 – erste Schicht 0.2 – Wände 3 – Füllung 10 % GyroidHigh Quality: Düse 0.2 – Schichthöhe 0.1 – erste Schicht 0.2 – Wände 4 – Füllung 0 %Ultra: Düse 0.2 – Schichthöhe 0.1 – erste Schicht 0.2 – Wände 4 – Füllung 10 % Gyroid  Danke und viel Spaß.

Fan Flow 360 Toroidal Air Duct X1C 风扇 气流 风扇流量 风道

Bambu Tuning

Bambu Lab

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014267/design/2023-09-19_1c59e405d0a79.png"></figure>This is a V-twin engine model that consists of various parts like a crankshaft, connecting rods, camshafts, gears, and a throttle valve, among others. It can replicate the functioning of a real engine. The engine model has magnetic decorative covers and hollowed-out structures that make it easy to observe the internal parts. It can be rotated using either a manual crank or an electric motor. In manual mode, the engine runs at a slow pace, allowing for a better observation of each movement. With the motor drive mode, the engine can run continuously by using the motor to rotate the crankshaft.&nbsp;Recommended filaments: Bambu PLA series, PLA Basic is recomended especially in moving parts<a target="_blank" href="https://store.bambulab.com/products/pla-basic-filament?variant=40820833517683" rel="nofollow noopener">https://store.bambulab.com/products/pla-basic-filament</a>Hardware Kit: Engine Model Components Kit-005<a target="_blank" href="http://store.bambulab.com/products/engine-model-components-kit-005" rel="nofollow noopener">http://store.bambulab.com/products/engine-model-components-kit-005</a>&nbsp;Please make sure you clean the build plate before printing and/or applying glue to prevent print failures.&nbsp;Follow the video tutorial step by step to print and assemble your build. <figure class="media"><div data-oembed-url="https://youtu.be/wv3qnfMbuko"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/wv3qnfMbuko" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Engine Model 005

Projekte_Modelle

trixs3D

I added a model without holesWithout supports

Knitted cat / pencil holder

Nadine

Jopek Design

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/584776/2024-01-09_5f1uaq5tqz04.png"></figure><h4>Dimensions (LxWxH)</h4>170 x 83,88 x 53,43 mm (100% scale)<h4>Basic information</h4>Have you ever wanted to hold a Great white shark, or keep it as your pet? Here's a good alternative.This shark is divided into 7 articulated segments with 2 movable fins, which grant the model with lifelike feel, and movement. It's quick and easy to print, and doesn't require any supports.<h4>Files information</h4>I've included one file in the .stl format.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/584776/2024-01-09_z81w1zxs9hqc.png"></figure><h4>Material</h4>PLA<h4>Layer height</h4>0,2 mm<h4>Infill</h4>>10%<h4>Support</h4>None. The model was designed not to require any support material.<h4>Scaling</h4>Possible, downscaling is easier, than ever before! If you have a well calibrated machine, you can downscale the model without any need for concerns. If you won't go way too crazy with downscaling, you shouldn't run into any issues.<h4>Orientation</h4>Default, laid flat on the belly<h4>Adhesion aid</h4>Not necessary, contact area with the buildplate should be sufficient. If your print surface suffers from poor adhesion, consider using an adhesive spray, or an other kind of adhesion booster. Using a brim is possible, but not recommended, as it would be difficult, and inconvenient to remove afterwards.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/584776/2024-01-09_jcskr84f88bu.png"></figure>In this section, you can find a list of all updates and fixes, which were introduced to the model along the way. Each update will be explained thoroughly, so that you know, which issue was every specific update adressing. If you're having any problems with the model, you can check here, if a new, revised version of the model, has already been released in a response to your problem, or not.If you run into any issues with the model, please pay a visit to a section of known issues, which can be found just below the Updates and fixes. If you won't find your specific problem in there, don't hesitate to contact me via dm!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/584776/2024-01-09_csvj2i5i5nbc.png"></figure>There currently aren't any known issues/work in progress. If you run into any, please contact me via dm.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/584776/2024-01-09_9vzf67hm3kch.png"></figure>My work is free for personal, non commercial use. If you want to sell, or monetize my models in other way, please contact me via dm, and we will discuss details, terms and conditions, and your individual pricing plan.

Articulated Great White shark

Sonstiges

vandragon_de

At 368 metres, the Berlin TV Tower is the tallest building in Germany and the fourth tallest TV tower in Europe. The TV Tower is located in the Park am Fernsehturm in Berlin's Mitte district. In 1969, the year it was completed, it was the second highest television tower in the world and is one of the ten most popular sights in Germany, attracting over one million visitors a year.

Berliner Fernsehturm (Berlin television tower) 1:500

Wahrzeichen

Willi 3D

Create your own battle droid army and take over the galaxy!&nbsp;If you like this model, please throw me a like. Designing the models is time, filament and coffee consuming. <a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=WGL5LXN5EHEXN" rel="nofollow noopener">If you want to support my work bye me a coffee.</a> Thanks!&nbsp;Description:This is a KIT CARD remix of my B1 battle droid. I changed the design in many places to make it easier to assemble and allow the figure to stand and pose on its own. Check out the compatible <a target="_blank" href="https://makerworld.com/de/models/13746?profileId=13457" rel="nofollow noopener">STAP speeder bike</a>!Scale 1:9 (90% for 1:10)&nbsp;Improvements:- improved connection points- easier to assemble- improved stand and pose of the figure- Blaster *pio* *pio*- kit cardsMay the force be with you!Roger roger!&nbsp;Update:(21/08/23) <ul><li>optimized base</li></ul>(03/08/23) <ul><li>optimized size for smaller printer and better to print fingers</li><li>addet base and insert to chest </li></ul>(26/07/23) <ul><li>optimized fit of head, thin, pipe, backpack and blaster</li><li>addet thumb to forarm, hole for blaster in backpack</li></ul>(13/07/23) <ul><li>optimized fit of ankle and blaster</li></ul>&nbsp;Printing:Layer height: 0.1Supports: NoBrim: NoMaterial: PETG, (ABS), (PLA)&nbsp;Assembly: The connections are designed and optimized for PETG, the use of PLA or ABS makes assembly more difficult.It is better to rotate the knee and elbow joints than to push them into place.In order to replicate the design of the B1 battle droid as closely as possible, I was forced to make some parts very fragile. Please be ready to reprint parts in case of breakage. Separate parts are located in the respective folders.

Kit Card B1 Battle Droid Star Wars 

Star Wars

Baum5

This is a winch mount for the TRX 4/6 and sport. It is mounted between the front fenders instead of the battery holder at the front. All holes are prepared for M3 screws.

Traxxas TRX4 trx6 tr front winch mount

TRX6

tgsparky77

Loved the original design but needed ones for the 3 and 5 slot version. I would suggest printing them in at least PETG. I printed them in PETG-CF as they come out looking more professional than normal PETG.