user_59955145

snowgoon360

TPU Generic Case for iPhone SE v2.  I believe the SE v2 is the iPhone 8, so it should work for that as well, but I have only test fit it to an Iphone SE version 2.  Optimized for no-supports, as with most TPU prints, you may get a minor amount of stringing.  I&#39;ve made about 12 of these so far and it really only has minor stringing in the inside because the sides of the phone are rounded, so you get a slight overhang.  With how this fits, I kinda doubt it will work with a hard material.  This was designed specifically for TPU.  If you want to add your own graphics that don&#39;t go all the way through, I found that if you keep it shallow (around 0.25mm), that it should print without issue.  I printed this on a high temp bed, which gives a matte finish, so for the logo, I found that it was best to create the inset region as a border, so that you get the matte finish on your logo/graphic, and not the overhang, more glossy look.

iPhone SE version 2 Phone Case TPU

phone cases

BlkWgn

Battery Mounts for securing a <a target="_blank" href="https://amzn.to/3TV6ZNl" rel="nofollow noopener">CHINS LiFePO4 12V 20AH Lithium Battery</a> vertically. I originally made <a target="_blank" href="https://makerworld.com/en/models/132693#profileId-143877" rel="nofollow noopener">brackets</a> to hold the battery on its side, but also needed to hold the battery vertically and that's where this model came from. I used 2 of the horizontal brackets connected with a gusseted shelf to take the weight and support the battery. The top is secured with 2 of the original brackets. The brackets have a 2mm clearance on the battery to leave room for a bit of <a target="_blank" href="https://amzn.to/3TQIil1" rel="nofollow noopener">foam tape</a> (affiliate link). The foam I used was about 6mm, this gave good compression when screwed down and keeps the battery secure. 6 holes sized for #8 pan head screws in each bracket. This was printed in <a target="_blank" href="https://amzn.to/3TUUTUq" rel="nofollow noopener">eSun PLA +</a> vertically with support

CHINS LiFePO4 12V 20AH Lithium Battery Mount

Lifepo4

Hi,&nbsp;Today's upload is a 3D printed PC Case, here is the specs:<ul><li>Supports up to ATX sized motherboards.</li><li>Standard ATX power supply.</li><li>GPU size up to 295mm</li><li>3x 120/140mm fans in the front, also support up to 420mm AIO.</li><li>2x 120/140mm fans on top or a 120/140/240/280mm AIO support.</li><li>1x 120/140mm fan in the back.</li><li>2x 3.5" front bay slots. (No front bay slots also available)</li><li>More than 10x 3.5" drives</li><li>Compatible with dust filters on top and front side.</li><li>Power and reset custom buttons</li><li>2x holes for 5mm LEDs for power/storage/network status.</li></ul>To assemble everything you'll need other parts: - M3x4 inserts - M3x6 screws - M3x8 screws Outside dimensions are 426x239x474mm (LxWxH).&nbsp;Update 1: - Fixed the orientation of the PSU mounting holes - Added an SFX PSU adapter plate (that mount on the original part)&nbsp;You can follow the all journey, behind the scenes and more on my instagram, check it out: <a target="_blank" href="https://www.instagram.com/lazyxworkshop/" rel="nofollow noopener">link</a>

phone cases

Lifepo4

ATX cases