log1c

Sakul

📐Corner Clamp for Woodworking🪚 I needed some corner clamps for a woodworking project that I&#39;m currently working on.Most of the corner clamps I found still needed a traditional one-hand clamp for tightening, so I designed my own that are fully 3D printed and don&#39;t need additional parts. I increased the wall count a little bit in the print profile to ensure that the parts are strong enough. The thread in the rail may look a bit rough after printing, but it worked like a charm without post-processing.  You may also like: <figure class="table" style="width: 98.39%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/484385#profileId-396742" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000176297/design/2024-06-04_8706199eaa5e9.jpg"></a><figcaption>🍦Pop &amp; Catch Toys Ice Cream Cone🍦</figcaption></figure></td><td><figure class="image"><a href="https://makerworld.com/en/models/447981#profileId-354736" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000176297/design/2024-05-01_1338867632a42.jpg"></a><figcaption>🐷Minecraft Animal Farm Pack🐮</figcaption></figure></td></tr></tbody></table></figure>

Corner Clamp for Woodworking

wood working

KKSP

Two-piece towel rack.

Towel Rack

home makes

denwagg

Stores Spools. Uses 4-1" id PVC tubing, 1.315 OD, 1.029 ID any length you choose. Designed to fit on 256mmx256mm Plate. Hot glue joints added if you choose to permanently attach together. No supports needed. Make these as long as you want I used 2ft sections of pipe. Also designed to stack as high as will allow the weight using the adapter included. Designed in Solidworks&nbsp;PLA or PLA+ works great, I used .25mm step, 2 walls 10% gyroid fill. On P1P Center takes 5hr, Both bottoms take 3.5hrs and both tops take 5 hours. Total of 19 hrs print time.&nbsp;12-22-23Added adapter to allow you to stack multiple racks&nbsp;12-31-23Modified Print Profile to include adapters if needed&nbsp;01-24-24Added Shelf mounts

Spool Rack

office organization

BjörnB

I have had great success with this profiles. Both on Bambu lab TPU-HF and some random noname TPU from amazon that actually handles higher speeds.NOTE: always dry your filament before printing. =)&nbsp;Overture High Speed TPU is confirmed working with this profile.

Bambu lab TPU-HF profiles (Printer and filament)

calibration

KobaRiley

<h2>Cable Tidy for Bambu X & P Series</h2>Got a bit tired of the messy setup on the back of the printer, and designed some cable supports that don't need screws or magnets.Also got a bit carried away and designed a few different versions.&nbsp;The PTFE tube on the right side, that goes to the printer, is free to move back and forth, but stays in the channel.The cables and tubes keep everything in place, but I've added some double sided tape on mine to keep it a bit tidier.<h3>Install</h3>To install the plate, you need to remove the two cables, and the left hand side PTFE tube. Then, remove the PTFE tube at the connector closest to the printer… feed that tube through the hole in the cable tidy plate, and then just reconnect everything.&nbsp;I've had this running on two printers for about 20 prints each, and have had no issues.&nbsp;There are different designs available, from 4, 3, 2 and 1 colour. The 1 colour basic version is by far the fastest to print… The Texas version is my favourite, and looks much better in reality than my awful photos….&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/601192/2024-01-16_432ca9585a8cb.jpg">&nbsp;&nbsp;The cables and tubes can still be removed with the standard little tools that are everywhere on Makerworld, but I've included a couple that fit slightly better with with this plate.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/601192/2024-01-16_6a6ab2a212209.png"></figure>&nbsp;This project took several days, and many many test prints. If you like the model, and feel like buying me a coffee, it would be greatly appreciated. <a target="_blank" href="https://ko-fi.com/kobariley" rel="nofollow noopener">https://ko-fi.com/kobariley</a>&nbsp;

wood working

home makes

office organization

calibration

x1 upgrades