user_4176535848

Techro3D

Classic bird feeder | octagonal house | with mounting bracket| By Techro3D&nbsp;<ul><li>Water drainage.</li><li>Mounting bracket.</li><li>Suspension point for a fatball or other bird food.</li><li>Bottom also suitable for placing food.</li><li>Removable roof.</li><li>100% printable.</li><li>No glue required, but can be used just to be sure.</li></ul><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453035/design/2024-05-04_a142276d19e56.png"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453035/design/2024-05-04_bf6862079a949.png"></figure>

Classic bird feeder, octagonal house.

zaujimave

LayerLux3D

Taken from the video game Fallout 4. Posed and edited with Blender.

Fallout T-60 Power Armor

movie

GekoPrime

I tried another spool winder but found it finicky and delicate.I designed this winder from scratch to be simple and robust, using the same self reversing leadscrew mechanism found on industrial cable windersWhy pick this model:<ul><li>Prints on a single build plate</li><li>Doesn't require heat set inserts or exotic hardware</li><li>Fusion and STEP files are available, remixes welcomed</li><li>Generous clearances, simple mechanisms</li><li>Designed to be a tool, not a project</li></ul>Print time:<ul><li>~500 grams of filament</li><li>~22 hours on Bambu Lab X1</li><li>~5 minute assembly</li><li>~2 minute spool transfer</li></ul>Hardware requirements:<ul><li><a target="_blank" href="https://www.amazon.com/s?k=608+bearings" rel="nofollow noopener">14x 608 skate bearings</a></li><li>A scrap of PTFE tubing</li><li>An electric screwdriver or drill with <a target="_blank" href="https://www.homedepot.com/p/DEWALT-MAXFIT-3-5-in-2-Philips-Bit-DWA3PH2MF/309474882" rel="nofollow noopener">a bit cut from ¼ inch hex stock</a> (most <a target="_blank" href="https://www.amazon.com/ITP1201-SCRWDRVNG-2IN-1-IMPAC/dp/B01LZZ7AOS/" rel="nofollow noopener">cheap quick change Philips bits</a> in the US fit this requirement)</li></ul>Print settings:<ul><li>Any. I used "0.16mm Optimal" in BambuSlicer with 5% adaptive cubic infill </li><li>Use 100% concentric infill for spindle_male_driven</li><li>Try the STLs if you have a problem with the 3mf files. I’ve added (xN) to each file name so you know how many to print</li></ul>Materials:<ul><li>Any. I used Polyterra and iiidmax PLA+</li><li>Use TPU for tpu_consumable_wiper_blade. I used Priline 98a. The wiper blades aren’t 100% required but they help keep the windings nice and tight</li></ul>Assembly and usage:<ul><li><a target="_blank" href="https://youtu.be/DxgkYDrRK-U" rel="nofollow noopener">Demo video</a></li><li><a target="_blank" href="https://youtu.be/-Hy69YwRLBw" rel="nofollow noopener">Assembly video</a></li><li>The side that says “Pastamatic" needs to face outwards, away from the spool</li><li>The filament needs to come in under the target spool, like this: O____O<ul><li>[not like this: O‾”‾”‾”O]</li></ul></li><li>The drill/driver needs to run clockwise, as though you're screwing something in</li><li>Accelerate slowly until the winder gets started</li></ul>Change log<ul><li>2023-05-28<ul><li>Initial release</li></ul></li><li>2023-05-29<ul><li>Fix a minor export glitch in "leadscrew_tooth"</li><li>Increase the number of “pin_short” instances in the 3mf from 6x to 8x</li></ul></li><li>2023-05-30<ul><li>Add a second prearranged 3mf with two plates to avoid overlap warnings</li><li>Disable autogenerated brims for the single plate 3mf </li><li>Add STLs for people who have trouble with the 3mf</li></ul></li><li>2023-06-03<ul><li>Add a ring to passive_target_cradle to prevent the far end of the target spool lifting if a user lets the the drill hang loose</li><li>Add a pin to driven_target_cradle prevent the leadscrew popping out</li><li>Fix a minor clearance issue where a dovetail didn't fit quite right</li></ul></li><li>2023-09-30<ul><li>Reduce chamfer on the crossbars to prevent them falling over when bed adhesion is poor</li><li>Add some holes to the crossbars to make them easier to screw down</li><li>Add some popular acessories to the all-in-one .3mf</li><li>Add a printable spool to the all-in-one .3mf</li></ul></li></ul>How to contribute:<ul><li>Post your make, it keeps me motivated to improve the model when I see people using it!</li><li>Post your feedback, idea or remix in the comments!</li><li>There are a few improvements and accessories in development as remixes, check those out if you‘re up for the alpha/beta tester experience<ul><li><a target="_blank" href="https://www.printables.com/model/498743-pastamatic-37-mm-motor-mount" rel="nofollow noopener">Adapter for 37mm gear motor</a></li><li><a target="_blank" href="https://www.printables.com/model/556405-pastamatic-filament-spool-winder-modifications-bra" rel="nofollow noopener">Source spool holder for 5 KG spools</a></li></ul></li></ul>Credits:<ul><li><a target="_blank" href="https://www.printables.com/@MiklosKiszely_486882" rel="nofollow noopener">@MiklosKiszely_486882</a> for the original idea</li><li><a target="_blank" href="https://www.printables.com/@PsychoShaft_33891" rel="nofollow noopener">@Psycho Shaft</a> for the drag/tensioner concept</li><li><a target="_blank" href="https://www.youtube.com/@thang010146" rel="nofollow noopener">thang010146</a> for YouTube videos of mechanical mechanisms, particularly the self reversing leadscrew for a level cable winder</li></ul>&nbsp;

zaujimave

movie

3dtlacka