It is a SillyShell holder and rear sight for the SillySledge, a SledgeFire that has been converted to shoot SillyShells. If you use the SillySledge Stock AND keep a shell in the barrel, that's 6 shells ready for use! There is a little groove on the back that should grip the shell (especially on the print layers)! Two versions; V2 has a more aggressive bump to snap into the lock of the Nerf rail. V1 is good if you want to try and snap it to another nerf blaster.

Made my N-Strike barrel attachments work with rival. I added modifers to the models in the 3mf file to print 100% on the lugs. Three models, one and three have different sized holes. NOTE: to fit the Mirage XXIV-800, lower the model (Z Axis) 1.2mm (From 38.33 to 37.30).

The Mirage lug channels are a little smaller than the lugs in the original Rival Loudener. So I just trimmed them a bit and it fits just fine!

Separated the barrel and SCAR from the Silly Shell 8 inch barrel sniper and stuck it on a single shot n-strike SledgeFire shell of my own design. Made two versions, one with just the barrel stuck on there, and the other with some reinforcement around the barrel to keep it from snapping off too easily. It will only work with a SledgeFire with the ejector removed, so keep that in mind. (won't fit)

Made another vase for my wife. This one only has holes to thread a string through to hang on a nail. A little easier to hang, in my opinion. Added the .3ds file with the two versions. They can be printed standing up with no brims, but you can add brims if you want.

My wife was looking at some vases online. Saw one that looked cute. She asked if I could create it in my 3D program. I gave it a shot. Afterwards, she asked if i could make it look like wood. A good reason to buy some Wood tone filament. Took HOURS and a desiccant change to get the filament to dry, but it came out pretty good! I split the vase vertically so that the front face with the lines printed as one sheet. Then I glued onto the “bottom” part.

Watching a youtube video calling silencers “cans”. So i just had to. You can take off any label from a 15/16 oz. can of anything, or make your own. comes in two pieces. Just superglue the top cap to the corresponding can.

You can take off any label from a 15/16 oz. can of anything, or make your own. comes in two pieces. Just superglue the top cap to the corresponding can.

Watching a youtube video calling silencers “cans”. So i just had to. In two parts in order for a clean print.

Wanted my SledgeFire to look like a sawed off stock. With or without a hanging loop.

Basic stock removal for SledgeFire. Made this while perfecting the connection for the SledgeFire stock.

While making this, it eventually looked like a Flame Thrower barrel attachment. Edit: I made the walls of the first model a little thinner and the holes a bit bigger. I also set up the seam to be at the bottom of the barrel. The 3MF file has some modifers that add a 100% infil where the lugs are located.

so i bought a Worker Prophecy to mod up with parts, and the main blaster didn't have a top prime. And they didn't' sell a top prime, just kits to make it a pump or a bolt action (with extra parts to buy!) So i just made one.

If you used my conversion kit to make your SledgeFire shoot Silly Shells, you will need to replace the standard stock with this bad boy. Why? 3 shell storage! Edit: added two Slide holder parts with the name "SillySledge", if you want.

Have a rival blaster with a lug? What can you put on it? Why not a Loudener? Want the Rival lug mount for the Battle Axe? https://makerworld.com/en/models/1597695-reinforced-muzzle-for-battle-axe

Screw was a spare screw from the OOD hardware kit. It is the regular Battle Axe muzzle with reinforcement. It is the regular Battle Axe muzzle with reinforcement. I extended the front picatinny rail to screw into the muzzle from the top. May not be the strongest, but it is something. Made this while I was working on my Rival Lug model.

Have a rival blaster with a lug? What can you put on it? Why not a Loudener? The sights will be useless but WHO NEEDS THEM! Your opponents will run away when they see this bad boy pointed at them! Printed with no supports while pointing up, but yes, have a outer brim. Seam set up to be at the bottom when mounted. Included the Bambu file, in case anybody wants to use it.

Created a shell that is the full length of an Elite shell. You can shove two short darts in it, as well. Why? I just HAD to make the shell the same length as the foam of the dart. :( (Also, so I could keep the surface clear of any markings. Nice and smooth.)

Downloaded some free Mega shells for my Pilot; was not happy how my A1 printed them. So I made my own. No text or anything on the shell, just smooth. Tested it out and it seems to work fine. Made the shell take up the whole 3 inches of foam, so it should have some power (I just lost a dart shooting it across the living room to my room). My first model.

This is a tale of my desire to have perfect SledgeFire shells for my stock SledgeFire.