1Pixel

wpetheri

I knocked up this design for my wife's work with kids. Also be good for car trips and the quick escape from boredom. You need to print five of each game piece

Tic Tac Toe - Three in a Row

Ebba

Encrust3d

1/26/2026 update: u/Flyrockets informed me of an error that is occurring on Firmware 01.01.50.24 (beta tester firmware) that the nozzle will hit the build plate aligner after the third layer and cause an error, causing the print to stop. I have updated this design to lower the aligner to be 0.5mm above the Textured PEI build plate vs the 3mm it was previously. This shouldn't cause any errors as the third layer should be over 0.5mm in most cases, but I do not have the 01.01.50.24 firmware to confirm. Please let me know if you experience any errors while using this updated design and I will update it again. To easily remove your build plate aligner and update to the new one, remove the old build plate aligner starting with the lober side and simply push it down and off the heat bed.&nbsp;If you are enrolled in the beta firmware program with Bambu, please check your printer firmware before printing. If you are enrolled in the beta firmware program with Bambu, you will need the updated design. If you are not part of the beta firmware program, the original design will work great for you if your firmware is 01.01.01.00 (stock firmware)&nbsp;This is a guide for aligning the build plate on the Bambu Lab A1 printer I designed in Fusion 360. I have been having problems getting my build plate perfectly straight on my new A1 printer so I designed this to clip on to the right rear corner of the A1 heatbed to help align the build plate. This build plate aligner prints in less than 20 minutes and uses less than five grams of filament. This design has been tested to ensure it does not interfere with bed leveling or nozzle cleaning. This design needs to be printed in the orientation I have uploaded it in for proper fit.&nbsp;You can not mirror this design and use it on the left rear side of the bed. The nozzle will hit it when changing filaments or cleaning the nozzle and cause the print to stop.&nbsp;Printing in PLA works, but PETG is the better material to use for this aligner. If you find this model to be a little loose, it is to ensure it can be removed from your bed if you do not want it on anymore. I had numerous versions of this that fit perfectly but had to be cut off to be removed. I do not want you to have to cut this off of your printer if you want it removed.&nbsp;If you are interested in a A1 heatbed cable support clip, you can download it here: <a target="_blank" href="https://makerworld.com/en/models/118957#profileId-127976" rel="nofollow noopener">https://makerworld.com/en/models/118957#profileId-127976</a>&nbsp;

A1 Build Plate Aligner

Bambulab

Fyrby Additive

These are easy to lose and break. I lost mine, then found it again and used it as inspiration to design this replacement from scratch. This slides on and fits perfectly in my test print, just tight enough, and also the screw holes are the same width, and width apart as the original bracket.&nbsp;If you would like to view the 3D model in colour in your browser and with optional AR, this is available <a target="_blank" href="https://collaborate.shapr3d.com/v/AH9AO46DqPgwx2-IQz21Q" rel="nofollow noopener">directly at the Shapr3D viewer here</a>.&nbsp;Printing&nbsp;Please print it in the orientation as per the main photo above. I used a brim just in case. Consider that if it is outside you may want more infill and also to use a more UV resistant material like ASA.&nbsp;An 0.4 nozzle and a 0.2mm layer height worked well for me.&nbsp;Support&nbsp;If you like our work please <a target="_blank" href="https://www.printables.com/@FyrbyAdditive" rel="nofollow noopener">consider joining our club on Printables</a>!

Ubiquiti UAP-AC-M (AC Mesh) Wall Mount Bracket

To print

Julian Hof

Hello everybody,&nbsp;This is an extremely compact filter for the xTool F1. (If you want to cut wood, it is not enough, but it is enough for engravings.) A HEPA filter and an activated carbon filter are used. Both can be easily replaced. The whole thing will simply be put on the suction nozzle.This is the used HEPA Filter:<a target="_blank" href="https://amzn.eu/d/c7Oy5PS" rel="nofollow noopener">https://amzn.eu/d/c7Oy5PS</a>This is the activatet carbon filter:<a target="_blank" href="https://amzn.eu/d/6fPw8Vq" rel="nofollow noopener">https://amzn.eu/d/6fPw8Vq</a>&nbsp;&nbsp;

xTool F1 extreme compact air filter 

Xtool F1

agepbiz

<figure class="media"><div data-oembed-url="https://youtu.be/SNWnS3XnjX8"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/SNWnS3XnjX8" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;I have been experimenting with a breakaway wingtip to improve on the silhouette of my design to match the real F14 better, while still being print-in-place and articulated. The wingtip breaks of with a satisfying snap and leaves a nice clean edge. I have also adjusted the wing shape and the angle of the tail fins. I have also included a version with a brim<h3>Commercial license</h3>Do you want to sell prints of this model? You can purchase commercial licensing for this model by <a target="_blank" href="https://www.printables.com/@agepbiz#join:144" rel="nofollow noopener">joining the Commercial license tier in my club</a> added a larger version (300). If you want to print the stands for it you have to upscale the stands to 150%Subscribe or follow me on:Subscribe or follow me on:Instagram: <a target="_blank" href="https://www.instagram.com/agepbiz/" rel="nofollow noopener">www.instagram.com/agepbiz</a>YouTube: <a target="_blank" href="https://www.youtube.com/user/agepbiz" rel="nofollow noopener">www.youtube.com/user/agepbiz</a>Twitter: <a target="_blank" href="https://twitter.com/agepbiz" rel="nofollow noopener">www.twitter.com/agepbiz</a>Printsettings:No support No raft 0,15mm-0,2mm layer height 35-45mm/s