user_380356169

emmaginn

Wall mounted bowl planter. Orient the planter on its top and you&#39;ll need supports. The wall mount should be oriented flat and should use support where the command strip groove is. Resize as needed. Hope you like it!&nbsp;Commercial Licensing: <a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Patreons</a> also have the opportunity to use commercial licenses for their own creative projects, adding versatility and potential income streams.&nbsp;If you like this, please be sure to check out my <a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Patreon</a> where I upload many of my designs exclusively for members. Hope you like them!&nbsp;<figure class="image image_resized" style="width:57.27%;"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000169692/design/2024-05-06_43c269eba0e6.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Stacker Planter/Vase with Hidden Drip Tray</a>&nbsp;<figure class="image image_resized" style="width:58.89%;"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000169692/design/2024-05-02_c4986346dbaf9.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Rivers Planter with Hidden Drip Tray</a> <figure class="image image_resized" style="width:58.58%;"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000169692/design/2024-05-02_ac819f1c0e73c.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Slice Planter with Hidden Drip Tray</a> <figure class="image image_resized" style="width:55.7%;"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000169692/design/2024-05-02_351443b9c636b.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Ripple Propagation Planter with Stand</a>

Modern Bowl Design Wall Planter

plant bits

Jamburgg

A simple chicken with a crochet / knitted look!&nbsp;The photos show the model at its default scale with a height of 80mm. The crochet pattern is likely to not show well if it is scaled down smaller than this, however I haven&#39;t tested it. You may want to experiment with a smaller scale and layer height.&nbsp;If you like the crochet style models, check out my baby duck! <a target="_blank" href="https://makerworld.com/en/models/404101#profileId-305771" rel="nofollow noopener">https://makerworld.com/en/models/404101#profileId-305771</a>&nbsp;Print Guide:Prints in one piece and can be painted either by hand or in the slicer if you have an AMS. I have included a single colour print profile as well as a painted -multi-colour print profile.&nbsp;The multi-colour version has 5 colours so there are two approaches you can take:<ol><li>Change the cheek colour (pink) to match the body (brown) and have the cheeks be the same colour as the body. You can either leave it like this or manually paint them.</li><li>It is possible to change out rolls in the AMS if they aren&#39;t being used anymore. Therefore I would set the colour of the comb (red part) to yellow and once the beak has finished printing, swap out the yellow roll for a red roll of filament.</li></ol>&nbsp;Walls/Perimeters: Any. Purely decorative so doesn&#39;t need any strength.Infill: Any. Same as above.Supports: NoneLayer Height: ≤ 0.2mm. Model was printed at 0.2mm layer height. A smaller layer height would give more detailMaterial: Any. PLA used here but any can be used

plant bits

cute bits