lars.komm

I had the problem that I occationally get poop ending up back on the build plate and the chute clogging from filament cought by the flap. Looking around for possible solutions I came across two models:<ol><li>@z3d's Purge Chute Extention on Printables</li><li>Downhill_Solutions' Poop Pop Stop here on Makerworld</li></ol>Although both solutions mitigated the problems somewhat, they were designed to adress only one problem at a time and were incompatible. The chute extension was great at avoiding filament getting caught by the flap and causing clogs, the poop stop did a very good job in reliably getting the poop off the nozzle and avoiding it to get slung back on the plate. I wanted a solution to do both.I remixed the chute extention to work inside the poop stop and did some motifications to the latter to allow for free movements of the flap. I also widened the opening of the poop stop and removed some internal structure as the flap now does that job.Print settings:<ul><li>For best performance print in Material that accepts higher temperatures like ABS or ASA.</li><li>Use at least 3 walls and 3 top-/bottom layers</li><li>You'll need some supports at the front part of the cover.</li><li>Use a wide brim with the flap</li><li>Other than that, default settings should work fine.</li></ul>Disclaimer: It works great for me, yet it may not work for everyone. I'm not responsible for any damage you do to your printer. It might work for the P1 series aswell but I couldn't test that. Print and install at your own risk. Caution! Be aware that there is a risk of bending your nozzle when the cover is not properly seated. Be aware of that!Other than that: have fun!&nbsp;Thanks to @z3d and Downhill_Solutions for their great work!!! Make sure you check out their work!

Bambu Lab X1 Poop Chute System

charlie.waterworth

CHECKOUT THE UPDATED VERSION HERE: <a target="_blank" href="https://makerworld.com/en/models/461128" rel="nofollow noopener">https://makerworld.com/en/models/461128</a> &nbsp;This little Dyson attachment can be inserted in to the seal of a filament vacuum dry bag and suction all the air out in a second or two!&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000165870/design/2024-02-01_f681c4c87e38a.gif"></figure>&nbsp;This is a way better option than the little hand pump that comes with the popular AliExpress/Temu/Amazon filament vacuum bags.&nbsp;Designed for my V8 and believe it fits all V models from V7 onwards? (V6 and older had a different connector design). Let me know in the comments which models it fits.

Filament Vacuum Bag Dyson Adaptor

我的收

Josh-3D

Check out the other two games in the series<a target="_blank" href="https://makerworld.com/en/models/140755#profileId-153348" rel="nofollow noopener">Checkers</a><a target="_blank" href="https://makerworld.com/en/models/134530#profileId-145997" rel="nofollow noopener">Chess</a>&nbsp;[Update] After getting some feedback, I adjusted the print profile, so the color change isn&#39;t discharged into the infill. I also increased the bottom shell layers. Since the main color scheme of this is white/black/green, it makes sense to reinforce those settings to avoid color bleed. Also added an A1 Mini plate for the Mini users!&nbsp;[Update 2!] Shout out to <a target="_blank" href="https://makerworld.com/en/u/840057458" rel="nofollow noopener">Wcad00 </a>for the added clip![Update 3!] Shout out to <a target="_blank" href="https://makerworld.com/en/u/982974221" rel="nofollow noopener">SoftWareCrash </a>and <a target="_blank" href="https://makerworld.com/en/u/425227684" rel="nofollow noopener">Adminstrator</a> for their contributions. The “Pocket” version, a 50% scaled version, and for a set of Xs and Os, with the Xs cut to fit inside the Os.&nbsp;A Travel TicTacToe game, for those long spans stuck at sea, where you don&#39;t want to risk using a pencil on the side of your life raft! Or uh, you know, any other occasion too, like road trips down the coast with friends, or spending family time playing games!&nbsp;Player piece quantity is setup so that X goes first!&nbsp;The clearance is tight. The X and Os should fit fine, but if your printer is sloppy, it might be a tight fit.&nbsp;&nbsp;-------If you like my work, consider showing your love by <a target="_blank" href="https://www.buymeacoffee.com/josh3d" rel="nofollow noopener">Buying me a coffee</a>. Additionally, if you&#39;re looking to sell prints of my design, please check out my <a target="_blank" href="https://www.patreon.com/josh3d/" rel="nofollow noopener">Patreon</a> page for more information.&nbsp;&nbsp;

TicTacToe - Travel Edition

MEOW

FilliFuu

Tread clicker fidget, taking inspiration from some of the best creations I have seen and creating a satisfying, easy to build toy. Requires no glue and can easily be assembled in under 1 minute. The track clicks either direction and is easy to spin, has been revised multiple times and tested for over a week. &nbsp;I printed this using elegoo pla, using a few supports, due to the spring required for the build its recommended against using silk as has only been tested using basic pla filaments. Please follow the print profiles as closely as possible.&nbsp;How to build -&nbsp;Step 1 - <img src="https://makerworld.bblmw.com/makerworld/draft/177713/2023-11-16_29c9202f26857.jpg">Remove all supports.Step 2 - <img src="https://makerworld.bblmw.com/makerworld/draft/177713/2023-11-16_140c47f8bd957.jpg">Gently flex the tracks being careful not to damage the hinge, so the track is able to freely rotate.Step 3 - <img src="https://makerworld.bblmw.com/makerworld/draft/177713/2023-11-16_da9e4aac60d8c.jpg">Insert the spring as per the orientation in the above photograph (you may leave the spring out if you intend to use without the clicker function.Step 4 - <img src="https://makerworld.bblmw.com/makerworld/draft/177713/2023-11-16_5c728b88676c5.jpg">Place the wheels inside the track as shown.Step 5 - <img src="https://makerworld.bblmw.com/makerworld/draft/177713/2023-11-16_964a0a8ccffd9.jpg">Lower the wheels and track simultaneously as shown above, gently moving the spring aside as you lower into the notches on the wheel as shown. Step 6 - <img src="https://makerworld.bblmw.com/makerworld/draft/177713/2023-11-16_aa1aad41a427a.jpg">Align the base and top with he orientation shown above and then gently click the two pieces together. Step 7 - <img src="https://makerworld.bblmw.com/makerworld/draft/177713/2023-11-16_fa34c2743f881.jpg">Done, rotate the track a few times ensuring the clicker function works - if the track feels stiff, rotate a few times further until the device rotates easily and enjoy.&nbsp;

Tread Clicker Fidget

玩具

NotJoel

Office organizer with 3 mini drawers. The main body has supports in the ridges. I recommend using a butter knife or a small blade to remove them. Print 3 dividers and drawers. If the dividers are loose, add a dab of glue to a corner.

X1

我的收

MEOW

玩具

办公用品