A C S

pbbence1994

My next kit card is based on a Red Bull Air Race MXS-R plane. Cut the parts out with pliers, nail sissors or hobby knife. The assembly is easy and self explanatory. The parts should fit togedhter tightly, but you can always use a bit of super glue to secure the parts together. Stay tuned for more Air Race planes! The pylon display will be also available to download soon check out my profile. Have fun printing it!

Air Race plane kit card (MXS-R Breitling)

gadgets

JamesThePrinter

This organizer is intended for your desk or 3D printer organizational needs. It features a mid-century feel with 6 separated storage areas. The included drawer should be used, but is not a requirement. The drawer handle requires 2 M3x12 bolts and is comprised of 3 pieces:<ul><li>Handle Support - Print 2x</li><li>Handle - Print 1x</li></ul>&nbsp;Print SettingsA brim may help with the handle pieces, but it is not necessary. No other special settings are needed.&nbsp;Drawer Assembly Instructions<ul><li>Insert both bolts through the holes in the drawer. </li><li>Slide the Handle Supports over the bolts. The flat end should be against the drawer. </li><li>Carefully screw the bolts into the handle. DO NOT OVERTIGTHEN. Because the handle is so small, it will crack if you overtighten the bolts. This is especially true if you use a silk filament. </li><li>Be sure to orient the curved end of the Handle Support correctly so that it pairs with the profile of the Handle.</li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/745895/2024-01-15_s740vq3lrdz5.png"></figure>&nbsp;&nbsp;<a href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Bambu Lab Matte Desert Tan PLA</li><li>Bambu Lab Matte Lemon Yellow PLA</li></ul>

Mid-Century Organizer

jojo

Squish3D

Do NOT adjust the thickness (Z) in your slicer!! The layers will not come out right. You CAN adjust the other dimensions (X,Y) though to make it bigger or smaller, just not the thickness.&nbsp;These were my settings and colors for my print that you see in the picture. Your results may vary depending on the filament you use and if you have your own HueForge profile saved with different settings.&nbsp;This is a long print without a Height Range Modifier (11.5ish hours). If your slicer has the capacity to do a height range modifier and you want to cut some time off, add one! The “Swap Instructions” below are for without a height modifier.&nbsp;Height Range Modifier Instructions (if your slicer is capable):You will want to add a height range modifier to the object of 0-1.44, with a layer height of 0.16 mm.The “Swap Instructions” listed below will not match up for the layer number listed, but the mm listed for each is still accurate and correct.&nbsp;Print at 100% infill with a layer height of 0.04mm with a base layer of 0.16mm&nbsp;Nozzle: 0.4 Filaments Used: PLA Sunlu Black Transmission Distance: 0.6 PLA BambuLab Basic Red Transmission Distance: 5 PLA Sunlu Gold Transmission Distance: 5 PLA Sunlu White Transmission Distance: 5&nbsp;Swap Instructions: Start with Black At layer #44 (1.88mm) swap to Red At layer #48 (2.04mm) swap to Gold At layer #50 (2.12mm) swap to White for the rest

Dragon in a Jar - HueForge

sculpture

thetonestarr

Remix of the BL Poop Chute with Magnets from Ga Design; I was consistently running into problems with it clogging before the waste would get to the bottom of the bin. This version has a 75% wider chute, allowing for the chunkiest of poops to properly flush out. Use 6mm wide x 2mm thick magnets. I used these https://www.amazon.com/dp/B07XRQ44VC

gadgets

jojo

sculpture

Printer addons