user_3602156824

适配YBA-AMS的远程电动送料、退料、回卷、缓冲一体耗材架，可置于干燥箱内。交流Q群：871779925拼装教程：<a target="_blank" href="https://www.bilibili.com/video/BV1YH4y1s7Vy" rel="nofollow noopener">https://www.bilibili.com/video/BV1YH4y1s7Vy</a>4通道PCB：<a target="_blank" href="https://oshwhub.com/yaoboan/yba-ams-esp32c3-board" rel="nofollow noopener">https://oshwhub.com/yaoboan/yba-ams-esp32c3-board</a>ESP32-C3 Code：<a target="_blank" href="https://github.com/YBA0312/YBA-AMS-ESP" rel="nofollow noopener">https://github.com/YBA0312/YBA-AMS-ESP</a>&nbsp;

[YBA-AMS] 远程电动料架 Electric filament spool holder

工具【打印机】耗材相关

Oxaspa

An elegant fan cover designed for the A1/A1 Mini, shaped like a dome !!! I added a print profile which worked very well after a few tries. But everyone can create their own and post it here... !!!

A1/A1 Mini Fan Cover

工具【打印机】A1+mini

starfalk

17.12.2023: I advice to not use additional tube clips because they restrict the movement of the PTFE tube too much, what leading to colission.&nbsp;I modified the original support structure to add a bit more clearance to the wire chain. In my opinion it is a minimal improvement, but atleast it looks cleaner ;)It would be nice if someone give me feedback. I will try to help or adapt the model.

X1 / P1P PTFE Tube Guide REMIX V2

工具【打印机】P1S

squinn

A must-have drill accessory tool that both allows you to make sure you drill a perfectly perpendicular hole while also capturing all of the dust and debris. The front of the tool rotates so that you can select the guide hole that will best work for your drill bit, and then the cover on the back can be easily removed with a twist to dump the debris when you're done. A protruded pointer is included on the top of the piece to help with alignment.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/163361/2023-11-11_s7cilgno7l35.gif"></figure>This model has been designed so that no supports or brim are required, and the STLs are oriented as they should be on the print bed. Post print, the front and middle piece can be simply snapped together, so no glue or other hardware is required. I printed all three pieces of the one shown in the pictures in PLA, but TPU would likely work really well for the bottom “cover” piece if you have it.

Drill Guide and Dust Catcher

工具

Ryan Tam

使用 PETG 材料打印，并开启“检查薄壁”选项

LaiFen 莱芬电动牙刷底座

日用

多色

EEEEEE

Prints on the Bambu P1S in exactly 30 minutes with the provided 3mf file. Print in PLA with 100% infill. Be careful not to bend the wings while removing from the build plate.&nbsp;Check out v5, a biplane: https://makerworld.com/en/models/451625#profileId-358694&nbsp;Instructions:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000441352/design/a631e2e3-d7e7-4134-a565-da440a1b61a6.webp">-Once you take the glider off the build plate, flip it over(flat side facing up) and fold the two elevators up as shown above. Fold between 30 to 45 degrees, it is better to fold lower than higher.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000441352/design/28448b2f-4532-49e0-ad68-680542cabfb1.webp">-Next, fold up the 2 stabilizers exactly 90 degrees. Make sure that the weighted side of the head is facing down relative to the stabilizers and elevators.<figure class="image image_resized image-style-align-left" style="width:216.484px;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000441352/design/9e8451c0-c27c-40bd-ba7c-717e3de141a6.webp"></figure>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;The glider should look similar to the image shown. To throw, hold between the wings and head of the plane. Throw it like a dart, but with less force. If the glider flies to the left or right, make sure that the stabilizers are at a 90 degree angle or manually adjust the flaps on the stabilizers. If the glider doesn&#39;t stay at the same height, lower or raise the elevators until it does consistently.

工具【打印机】耗材相关

工具【打印机】A1+mini

工具【打印机】P1S

工具

日用

多色

玩具