Bigemon

glogger

Replacement butons for your Steam Deck. The buttons are bare ready for you to add whatever symbols you desire. The measurements are .1mm~ so your print may vary in size due to heat shrinkage etc. They're not perfect but I shall try to perfect them in future updates to my designs.

Steam Deck Replacement buttons

SteamDeck

BrewBoy

Plinker V2.0 (Bolt-Action Blaster):&nbsp;The second entry in my shell-ejecting plinker series. The V2.0 features a bottom loading magazine and functional rails for mounting accessories, STEP files are included if you would like to make your own adjustments or parts. This is an ongoing work in progress as I continue to make improvements and different accessories to allow for lots of different customizations.&nbsp;Only requires a nuts, bolts &amp; a few springs (<a target="_blank" href="https://www.aliexpress.com/item/1005002523758634.html?aff_platform=true&amp;aff_short_key=UneMJZVf&amp;isdl=y&amp;src=bing&amp;pdp_npi=3%40dis%21CAD%211.49%211.49%21%21%211.88%21%21%40%2112000021005031078%21ppc%21%21&amp;albch=shopping&amp;acnt=135095331&amp;isdl=y&amp;albcp=412811419&amp;albag=1311717734383599&amp;slnk=&amp;trgt=pla-4585581970548950&amp;plac=&amp;crea=81982433154568&amp;netw=o&amp;device=c&amp;mtctp=e&amp;utm_source=Bing&amp;utm_medium=shopping&amp;utm_campaign=PA_Bing_CA_PC_customlabel1&amp;utm_content=customlable1%3D7&amp;utm_term=aliexpress%20305mm%20spring&amp;msclkid=91572ea3b6a41a4e20b94b3fbac2f23b" rel="nofollow noopener">305mm Compression Spring Wire Dia 0.3 0.4 0.5 0.6 0.7 0.8 1 - 5mm Outer Dia 3 3.5 4 4.5 5 5.5 6 7 8 10 12 - 60mm Length 305 mm (aliexpress.com)</a>) ***This link may not work in your region. Check the assembly guide for the required spring dimensions to help you find ones in your area.&nbsp;Firing Video: <a target="_blank" href="https://www.reddit.com/r/3Dprinting/comments/1bu5t05/plinker_v20_boltaction_toy_blaster/" rel="nofollow noopener">Plinker V2.0, bolt-action toy blaster : r/3Dprinting (reddit.com)</a>&nbsp;Please check out the Assembly Guide PDF for parts list and assembly Instructions. Short version has identical parts requirements and assembly, some parts may appear slightly different between versions.&nbsp;Check out the Targets and Ammo box I made for the Plinker V2.0: <a target="_blank" href="https://makerworld.com/en/models/441802#profileId-347641" rel="nofollow noopener">Ammo Box &amp; Targets for Plinker V2.0 by BrewBoy - MakerWorld</a>If you enjoyed this model then you will probably like my pump-action launcher: <a target="_blank" href="https://makerworld.com/en/models/229678#profileId-265500" rel="nofollow noopener">Pump-Action Plinker (Toy Launcher) by BrewBoy - MakerWorld</a>&nbsp;DRY FIRING MAY CAUSE THE BOLT TO BREAK.&nbsp;UPDATE (APRIL 17, 2024):<ul><li>Added Raw model files for long rifle version with a telescopic stock (Print profile and additional build info coming soon).</li><li>Small Updates to Build Guide.</li></ul>UPDATE: (APRIL 26, 2024):<ul><li>Added raw model files and print profile for two new accessories: Tactical Scope 0x &amp; Angled Foregrip</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000410146/design/2024-04-25_02ebb05dd0f38.png"><figcaption>Side View - X-ray Internal Assembly.</figcaption></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000410146/design/2024-04-17_a4c948f52ba57.png"><figcaption>Best Orientation for Printing</figcaption></figure>

Plinker v2.0 (Bolt-Action Blaster)

玩具

drodfro

3rd photo shows the capsule this funnel and tamper works with.

Capsulone filler and tamper

coffee

DatumCAD

<figure class="image image_resized image-style-side" style="width:34.11%;"><img src="https://makerworld.bblmw.com/makerworld/draft/696022/2024-03-12_f4af98eab96a6.gif"></figure>The aim was to design a Centering tool that:<ol><li>had no need for hardware (i.e. was fully printable),</li><li>was adjustable to make it suitable for various material stock widths,</li><li>that also included a second function that would make it more versatile.</li></ol>Other similar printed tools only seem to offer the one of these functions, and a lot of those focused purely on centering are ‘fixed’ and so become cumbersome on smaller stock sizes. Those that do adjust often use metal fasteners requiring tools.&nbsp;And so this design is the result of my efforts to solve the above and make a great multipurpose tool. I hope you like it!&nbsp;***Update 12/03/2024***: Imperial version added as many have asked for this, so there are now 2 print profiles to choose from ……“Metric” & "Imperial". I have also taken the opportunity to slightly reposition the number text to better align with the notches which should avoid any confusion when using these.<figure class="image image_resized image-style-side" style="width:50.08%;"><img src="https://makerworld.bblmw.com/makerworld/draft/696022/2024-03-12_b468c9f94b7b.gif"><figcaption>Centre Marking GIF</figcaption></figure>&nbsp;&nbsp;Function #1 - Centre Marking:&nbsp;The two knurled shoulder bolts (yep - fully 3D printable) can be screwed into whichever pair of holes best suits the width of material (Note: when spaced at the furthest setting the tool can span a width of 125mm max).&nbsp;Its then a simple case of sliding the tool along the length of the material with one shoulder bolt over each edge. Tip: apply a slight twisting force to keep the shoulder bolts ‘pinned’ against the sides while you do so.&nbsp;A pencil / pen can be used to mark through the conical hole, located centrally on the tool, which will prevent your line from wandering out of position. See animation.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<figure class="image image_resized image-style-side" style="width:50.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/696022/2024-03-12_fd61218b72569.gif"><figcaption>Edge Marking GIF</figcaption></figure>Function #2 - Edge Offset Marking:&nbsp;So this tool also incorporates stepped notches from 5-25mm (at 5mm increments). Allows quick marking out / scribing of measurements in from the edge of your material. This is really common when you are trying to quickly position fixings / pilot drill hole locations etc. See animation.&nbsp;&nbsp;Perfect for the home, studio, workshop…… Just print, assemble & put to use!&nbsp;I love designing for 3D printing, please take a look at all my other models which are all free (and will always continue to be)… if you value any of the downloads enough & are able to support me, then please consider buying me a coffee to keep me going! <a target="_blank" href="https://www.buymeacoffee.com/DatumCAD" rel="nofollow noopener">www.buymeacoffee.com/DatumCAD</a>&nbsp;

2-in-1 Centre Marking Tool

家居日常

grwang41

Round 5.6L drying box with humidity meter installation hole.&nbsp;Requires the following additional screw sizes. M3X8 3pcs&nbsp;

Round 5.6L drying box 

3D打印配件 - A1 Mini

Celestin

Are you tired of soldering cables for 5V projects ? Here's an adapter for Dupont connectors to easily get the + and - from a USB! This allows you to work on 5V projects using either a USB port or an external battery. No need for soldering, just insert the 2 cables for + and - and you're good to go! Plus, printing it is easy and doesn't take much time.

Dupont USB connector

电子配件

极光

需要配件 低压29mm涵道风扇 *1开关按键*1 <a target="_blank" href="https://item.taobao.com/item.htm?abbucket=14&id=620244733120" rel="nofollow noopener">https://item.taobao.com/item.htm?abbucket=14&id=620244733120</a>2串充电模块 *1 <a target="_blank" href="https://item.taobao.com/item.htm?_u=73umnb2p27c5&id=675344251762" rel="nofollow noopener">https://item.taobao.com/item.htm?_u=73umnb2p27c5&id=675344251762</a>mos开关模块 *1 <a target="_blank" href="https://detail.tmall.com/item.htm?_u=73umnb2pd5ae&id=679645885876" rel="nofollow noopener">https://detail.tmall.com/item.htm?_u=73umnb2pd5ae&id=679645885876</a>30A电调 *1 <a target="_blank" href="https://item.taobao.com/item.htm?abbucket=14&id=723520003886" rel="nofollow noopener">https://item.taobao.com/item.htm?abbucket=14&id=723520003886</a>m2*5mm六角螺丝*n 接线方法如下<img src="https://makerworld.bblmw.com/makerworld/draft/649626/2024-03-07_e2bc40eb8a01f.jpg">

21700版本暴力风扇21700 version violent fan

电动工具

Emashi

Thats adapter for old version of Xiaomi powerbank 10 000 mAh. It can be used to keep your powerbank next to your belt, or on Meta Quest 3 head strap. I suggest to print it on the side - then it will be stronger and more elastic. Also not with PLA, but with PETG. But thast just my suggestions, you can test it with PLA as well :)

Oculus Meta Quest 3 Xiaomi powerbank adapter

Quest3

craigandrews

My new keyboard came without keycaps so I decided to make some. Through a lot of trial and error, I learned how to create some nice keycaps - and that&#39;s what this model does. You can learn more about how I arrived at this point and some alternative approaches that may work better for your specific needs and objectives at <a target="_blank" href="https://candrews.integralblue.com/2024/03/3d-printing-high-quality-keycaps/" rel="nofollow noopener">https://candrews.integralblue.com/2024/03/3d-printing-high-quality-keycaps/</a>The 45-degree rotated orientation is harder to print (as there&#39;s only a tiny bit of the keycap touching the built plate), requires support (it produces waste and the support can be annoying to remove), and requires a lot more filament changes to print colored legends. So why use this orientation?The 45-degree angle orientation produces a much higher quality keycap top surface. With this orientation, the concave keycap top is smooth without visible (well, only visible with a bright light and very close look) or feelable layer lines, especially when using a 0.2mm nozzle. For the best, highest-quality printed keycaps, this orientation is the way to go.Adhesion is the biggest challenge, so any tricks to improve adhesion should be applied, including:<ul><li>Using a brim</li><li>Reducing the brim-object gap</li><li>Slowing speeds</li><li>Increasing the initial layer height</li></ul>The orientation is critical. The stem must have a solid part on the bottom. In other words, the slit that goes through the stem must be horizontal. Otherwise, there will be nothing for the support to hold, and the stem will fail to print likely resulting in spaghetti.The keycap model was generated using <a target="_blank" href="https://openscad.org/" rel="nofollow noopener">OpenSCAD</a> and <a target="_blank" href="https://github.com/rsheldiii/KeyV2/" rel="nofollow noopener">KeyV2</a> using this code:&nbsp;include &lt;./includes.scad&gt;$stem_inner_slop = 0.0; $cherry_bevel = false; bar_support() rounded_cherry() row_profile(&#34;mt3&#34;) no_stem_support() rotate([0,45,0]) { key(true); }&nbsp;You can now produce custom keycaps that look and feel great! Besides artisans, it&#39;s very much doable to produce an entire keyboard in a unique color for a very personalized look.