user_3105466529

Noot Noot

Update: V2Thanks to some constructive feedback, I have adjusted the model to allow for an offset to the back plate to allow the framed item to be held in place when there is no border to it. so if you have a photo that is 60mm by 90mm you can choose to cover a few mm on each side to hold it in place. &nbsp;Update 2: V3 I have added a stand feature to the back plate. The cylinders that come off the back plate should act as a stand. I have not been able to run a test print yet however to see how well it works. Will update this once I can get a test done or someone can verify. &nbsp;Update 3: V4I removed the old stand and created a new standalone stand that you can choose to include. I have also allowed for holes to be added to the frame for the frame to sit on screws. As expected all these can be adjusted. Please note, This is still a learning curve for me and as such, the stand angle will need to be a negative number to work. &nbsp;<blockquote>This is my first parametric model and I learned a lot making it. I have ideas for improvement and will continue to work on it and adapt it over time. I am incredibly proud of this one so please keep feedback to constructive only.</blockquote>&nbsp;The frame is very customizable. It came out of need after I wanted to frame some cards that are an odd size. I haven&#39;t been able to buy the frames so figured id make my own.&nbsp;You can adjust the photo size and width along with the number of rows and columns. You can also adjust the frames depth and width to meet your needs. The back plate can be adjusted and the finger holes diameter can be adjusted and spaced as needed.&nbsp;The back plate initially had pegs to hold it in place but I found the pegs to break off to easily and the back plate sits so snug that they weren&#39;t even required.&nbsp;My ideas for the future include:<ul><li>Options for mounting to IKEA peg board and others like multi-board</li><li>Different designs like a beveled edge</li><li>Ability to add text</li></ul>

Parametric Photo Frame

Michelle aznar

BuzzEye

Try not to fall in love with this two hugging cats 😻&nbsp;If you have AMS just use provided print profile&nbsp;Swap Instructions (if you do not have AMS): Start with black <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=43992830017755" rel="nofollow noopener">PLA Basic | Bambu Lab EU</a>At layer #6 (1.20mm) swap to Gray <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=46956524241244" rel="nofollow noopener">PLA Basic Filament with spool / 1kg / Black (10101) | Bambu Lab EU</a>At layer #11 (2.20mm) swap to Silver <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=43992829984987" rel="nofollow noopener">PLA Basic Filament with spool / 1kg / Gray (10103) | Bambu Lab EU</a>At layer #14 (2.80mm) swap to White for the rest <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=43992829919451" rel="nofollow noopener">PLA Basic Filament with spool / 1kg / Black (10101) | Bambu Lab EU</a>&nbsp;If you want you can use only 3 colors then:Start with black <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=43992830017755" rel="nofollow noopener">PLA Basic | Bambu Lab EU</a>At layer #6 (1.20mm) swap to Gray <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=46956524241244" rel="nofollow noopener">PLA Basic Filament with spool / 1kg / Black (10101) | Bambu Lab EU</a>At layer #13 (2.60mm) swap to White for the rest <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=43992829919451" rel="nofollow noopener">PLA Basic Filament with spool / 1kg / Black (10101) | Bambu Lab EU</a>

Cats hugging in heart shape Hueforge

Distancia de transmision heuforg

IngratoSocial

Esta es una modificación del 猫碗 CatBow 2 para que sea mas bajo

CatBow resized

gatos juguetes y comederos

designs.by.Marcum

The perfect way to bring your favorite wildlife species into your home!&nbsp;Wildlife Conservation is a topic that has been very near and dear to my heart since I was a small child, so it was only a matter of time for me to expand my Kit Card series to include various wildlife species. As the same with all of my others Kit Cards, these designs are simple and easy to print, but instantly recognizable as your favorite animal.<blockquote>In the universe are billions of galaxies, in our galaxy are billions of planets, but there is Only One Earth. It is important to remind ourselves that we only get one chance to protect and conserve the natural beauty of this world, and it is my absolute pleasure to bring awareness and life to some of the species that are most endangered of never being seen again.</blockquote>Current species included:<ul><li>African Forest Elephant</li><li>African Lion (Male and Female)</li><li>Dromedary Camel</li><li>Giant Panda (P)</li><li>Hippopotamus</li><li>Linnaeus&#39;s Two-Toed Sloth (P)</li><li>Llama (P)</li><li>Meerkat (P)</li><li>Mountain Gorilla</li><li>Polar Bear</li><li>Ring Tailed Lemur (P)</li><li>West African Giraffe</li><li>White Rhinoceros</li></ul>Animals above marked with “(P)” are located exclusively on Patreon, link below.&nbsp;The kit card connectors were designed to easily snap away, but for the cleanest finish it is recommended to use snips to remove them. Each animal may have a slightly different assembly, but the fundamentals remain the same amongst all of them.<ol><li>Snap all connectors to free each piece</li><li>Slide the ears into the cutout at the top of the head<ol><li>There are animals (such as the Lion and Gorilla) that use pegs and holes instead. For these you simply place the peg through the hole in the body and then squeeze the other side onto the peg.</li></ol></li><li>Slide the larger connector into the cutout at the front of the body</li><li>Slide the smaller connector into the cutout at the back of the body</li><li>Align to the two cutouts on the legs with the connectors and slide in</li><li>Repeat for the last leg</li><li>Enjoy!</li></ol>&nbsp;If you&#39;d like access to a Commercial License and exclusive designs not available anywhere else:<a target="_blank" href="https://patreon.com/designsbyMarcum" rel="nofollow noopener">Join me on Patreon</a>&nbsp;Filament used in product photography:<ul><li>Overture Matte PLA - Black</li><li>Overture Matte PLA - Light Gray</li><li>Overture Matte PLA - White</li><li>Overture Matte PLA - Light Brown</li><li>Overture Matte PLA - Chocolate</li><li>Overture Rock PLA - Rock White</li><li>Prusament PLA - Galaxy Black</li></ul>This community generated approximately $179 worth of points and boosts during the Animal Frenzy contest! On behalf of you all, I have donated $200 to the Fort Worth Zoo to assist in their conservation efforts. Thank you for all who took the time to show their love and support for my work.<blockquote><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000447508/design/2024-05-26_df146c068f725.png"></blockquote>

Wildlife Kit Card - Multiple Species

niños

潦草小狗爱吃雪糕

This is a mold for making spinning top from PLA filament purge. The tops made with this mold are very colorful and spin well. I printed the mold with PETG at 100% infill and did not need to use supports (PC might work even better).&nbsp;What you will need:<ul><li>An unused oven</li><li>A silicone mat (it&#39;s easier to flip and roll the melted PLA into a ball on a silicone mat than on a metal baking tray)</li><li>PLA filament purge</li><li>A 3M respirator or N95 mask (the fumes from melting PLA in the oven are stronger, so please protect yourself)</li><li>Work gloves</li><li>Tongs</li><li>Pliers</li><li>A digital scale</li></ul>Process：1. Accurately weigh 6g of PLA filament purge and place it in the oven.Preheat the oven to 200-230°C and heat the filament purge for approximately 5 minutes.2. Use tongs and pliers to shape the melted PLA into a ball. Evenly folded patterns will look better.3. Place the shaped plastic into the mold and press the mold firmly.4. After approximately 3 minutes, open the mold and remove the top. If the top is difficult to remove, use pliers to take it out.「Twisting and shaking the mold after it has cooled completely can aid in part release. I recently tried using a mold release agent (spray), and it has been very effective in ensuring smooth part separation.20240512」（translate from Google Gemini）&nbsp;&nbsp;这是一个使用PLA耗材废料制作陀螺的模具，制作出的陀螺颜色比较漂亮，旋转的很好。我用PETG 100%填充来打印模具，无需添加支撑（PC可能效果会更好）。&nbsp;你需要：一个闲置的烤箱，一个硅胶垫（需要把熔化的PLA翻折并团成一团，这在金属烤盘中很难操作），PLA耗材废料，3M防毒面具或N95口罩（在烤箱中熔化PLA产生的气味更大，请做好防护），工作手套，取盘夹，钳子，电子秤。&nbsp;压模步骤：&nbsp;1，将 6g（请准确称重）PLA耗材废料放入烤箱中，200～230℃加热约5分钟（烤箱需预热）<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_df4dbe446d418.jpg"></figure><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_74bd4a7599ef7.jpg">&nbsp;&nbsp;2，用取盘夹和钳子把熔化的PLA团成一团（翻折均匀的纹理会更漂亮）<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_31b36cc45d107.jpg"></figure>&nbsp;&nbsp;3，把团好的塑料放入模具中，用力挤压模具。&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_75a96c8b0fc52.jpg"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_06f1d6fa28797.jpg"></figure>&nbsp;&nbsp;4，大约3分钟以后打开模具取出陀螺。如果脱模困难可以用钳子把陀螺取出。<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_07f0433aa2577.jpg">&nbsp;&nbsp;「充分冷却后扭转并晃动模具将有助于脱模。我最近尝试使用脱模剂（喷雾），它很有效，可以确保顺利脱模。20240512」&nbsp;

Spinning top mold   陀螺模具

reciclar filamento

Myzhar

MyzharBot v5 is the new version of my robotic project → <a target="_blank" href="https://linktr.ee/myzhar" rel="nofollow noopener">link</a> Here you can find all the pieces to print the mechanics of the two tracks. You can find the project online on <a target="_blank" href="https://cad.onshape.com/documents/50acc1b7a8077e4c66d50557/w/84be38947baf954e1690c6ee/e/338f26cf9fb7ff02372a65f8?renderMode=0&uiState=63491f0ce112a47cef6c87e1" rel="nofollow noopener">OnShape</a> for assembling all the parts.&nbsp;Rubber tracks: <a target="_blank" href="https://www.rubtrack.com/project/robot-tracks/" rel="nofollow noopener">ROBOT TRACKS–A</a> / <a target="_blank" href="https://katodo.com/it/ruote-e-cingoli/313-lightweight-rubber-track-930x50mm-0616524533032.html" rel="nofollow noopener">Italian Store</a>&nbsp;Assembling video:<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=6hiwRmKusxc"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/6hiwRmKusxc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;The robot in action:<figure class="media"><div data-oembed-url="https://youtube.com/shorts/LsiQxACTibk?si=6uh-eSbJoOs_iDgT"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=LsiQxACTibk"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/LsiQxACTibk" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>&nbsp;

MyzharBot v5 - tracks

Fully 3d printed shoes<ul><li>TPU（85A is a good choice）</li><li>The default size is European Standard 42.</li><li>Please enlarge the size one to two according to the actual shoe size for better comfort and experience</li><li>Please refer to the magnification ratio in Crocs Shoes - Full 3d printed in MakerVerse Designs for magnification ratio.</li><li>If the shoe is too big to fit to the printers height, use the “WithSupport”-Version, rotate in Y-Axis (green) and use the cut tool in Bambu Studio to create a new flat surface parallel to the print bed</li></ul>35-83.33%        36-85.76%37-88.10%        38-90.48%39-92.86%        40-95.24%41-97.62%        42-100%43-102.38%      44-104.76%45-107.14%      46-109.52%47-111.90%      48-114.29% If you like this model, please boots to me, I will bring you a better model.Finally, I wish you a good printing experience,good luck&nbsp;全3D打印拖鞋&nbsp;<ul><li> 最好使用85A TPU（更软）</li><li>模型默认尺寸为42码</li><li>请根据直接平常使用的鞋码放大1-2码，这样更舒服</li><li>放大倍率请参照MakerVerse Designs大佬的Crocs Shoes-Full  3d打印的放大率。</li><li>如果鞋子码数太大打印机放不下，请使用Bambu Studio旋转并使用其中的剪切功能，创建新的平台接触面</li></ul>35-83.33%        36-85.76%37-88.10%        38-90.48%39-92.86%        40-95.24%41-97.62%        42-100%43-102.38%      44-104.76%45-107.14%      46-109.52%47-111.90%      48-114.29%如果你喜欢我的模型，请给我投一张助力票感谢&nbsp;&nbsp;

Slippers-Shoes-Fully 3D-printed-鞋-拖鞋

zapatillas, ropa y gafas

DoSc

I wanted a mount for my sunlu S2 Dryer - with little fillament usage as possible. And that it will fit with my setup with my AMS riser. So i used one original holder to have a perfect base (Sunlu S2 snuck perfectly in this holder base + the hole for the powercable was perfectly placed) and remixed it into my solution, so that the AMS chamber of the outer shell would be the main fix-point. The mount-plate is very sturdy (when you use my profile and good filiament) and the brackets are just needed to give some extra support and take some pressure from the AMS outer wall.&nbsp;Use 2x M4x4mm Threat inserts on the holder itself + 2x M4x16mm (sunkhead)screws to connect it to the angle brackets and some good double sided tape to fix the bracket with your printer or riser. I personally used some 3M assembly line (Montageband) with a possibility to hold 50kg/m² and it is very sturdy. (I didn´t want to ruin my riser, so a screwing at the bottom of the bracket was no option)&nbsp;It was a journey to develop something so simple, yet so complicated in the detail. But i hope it will be also a good fit for some other guys out there.

Sunlu S2 Holder for new AMS 

sunlu_S2

entroisdimensions_figurine

Raichu is now available, and you have the choice between different file formats:<ul><li>STL</li><li>3mf for Multicolor Bambu Lab printer</li><li>3mf for Multicolor Prusa printer</li></ul>Video of printing the model: <a target="_blank" href="https://www.instagram.com/polymaker_figurines/" rel="nofollow noopener">Instagram</a>, <a target="_blank" href="https://www.tiktok.com/@polymaker_figurines" rel="nofollow noopener">TikTok</a>, <a target="_blank" href="https://www.youtube.com/channel/UCScmlttdRwRbBA61ZGlUVJg" rel="nofollow noopener">YouTube</a> For printing, I used PolyTerra PLA filament from Polymaker: 5 colors version:<ul><li><a target="_blank" href="https://us.polymaker.com/products/polyterra-pla?variant=39574351904825" rel="nofollow noopener">PolyTerra PLA Pastel Peach </a>(for body)</li><li><a target="_blank" href="https://us.polymaker.com/products/polyterra-pla?variant=39574352232505" rel="nofollow noopener">PolyTerra PLA cotton white</a> (for belly and pupil)</li><li><a target="_blank" href="https://us.polymaker.com/products/polyterra-pla?variant=39574352298041" rel="nofollow noopener">PolyTerra PLA Savannah Yellow </a>(cheeks, ears and tail)</li><li><a target="_blank" href="https://us.polymaker.com/products/polyterra-pla?variant=39574351282233" rel="nofollow noopener">PolyTerra PLA Charcoal Black</a> (for eyes)</li><li><a target="_blank" href="https://us.polymaker.com/products/polyterra-pla?variant=39574351544377" rel="nofollow noopener">PolyTerra PLA Army Brown</a>( for paws, hands, tail and ear)</li></ul>To discover which new models will be released next, follow @polymaker_figurines: <a target="_blank" href="https://www.instagram.com/polymaker_figurines/" rel="nofollow noopener">Instagram</a>, <a target="_blank" href="https://www.tiktok.com/@polymaker_figurines" rel="nofollow noopener">TikTok</a>, <a target="_blank" href="https://www.youtube.com/channel/UCScmlttdRwRbBA61ZGlUVJg" rel="nofollow noopener">YouTube</a> Join the Figurines Community on <a target="_blank" href="https://discord.com/invite/r2ujMfEb7S" rel="nofollow noopener">Discord</a> Happy Printing!-----------------------------------------------Printer settings on the Bambu Lab X1C<ul><li>Rafts: No</li><li>Supports: Yes</li><li>Resolution: 0.2mm</li><li>Infill: 10%</li><li>Filament brand: Polymaker</li><li>Filament color: Orange, yellow, brown, white , black</li><li>Filament material: <a target="_blank" href="https://us.polymaker.com/products/polyterra-pla" rel="nofollow noopener">PolyTerra PLA</a></li></ul>

Raichu Multicolor

1 pokemon

Andrew Ho

The main purpose of the case is to store and protect your glasses. The case can be closed with a threaded lid. The whole design is waterproof and ensures your case to float on the water surface when you travel by boat. The case is rugged enough to withstand the hardest impact when traveling by plane.&nbsp;The inner diameter of the case is 51 mm, which should fit all common sizes of glasses. The tolerance between the case and the lid is 0.1mm. The case was printed on two different printers (BambuLab X1C & Prusa MK3) and the tolerance works just fine. The main layer height is 0.2mm. Variable layer height was set to on and is in the area of the thread set to 0.1mm.

Classes Case

gafas

Tala16

Lube Helper a1 x1c p1p p1s bambulab

Lube Helper a1 x1c p1p p1s bambulab

herramientas 3D

migralb

Nba Airless basketball standRotatesupport needed

Nba Airless basketball stand holder pokemon ball holder

balones de baloncesto

t147caddy

Legos Style Calibration Cube&nbsp;Check your printers dimensional accuracy.&nbsp;&nbsp;Be sure to give me a follow. :)

Legos XYZ Calibration Cube

test

Henlor

The goal of this model is the prevent the tensioner form tilting by containing it more on the Z and X axes. This will prevent the belt to wear unevenly and increase its life spend.   This model is compatible with the Creality K1, K1C, K1 Max  <h3>Recommended Print Settings :</h3>Material : ASA / ABSNozzle : 0.4Layer height : 0.2Perimeter count : 4Top / Bottom layers : 5Infill : 40%No supports  <h3>Bill of material</h3>2 x M3 x 30mm SHCS screws4 x M3 x 16mm SHCS screws ( for Creality K1C Only)&nbsp;<h3>Installation Guide</h3><figure class="media"><oembed url="https://www.youtube.com/watch?v=cDIDofgZDBI"></oembed></figure><ol><li>Remove the screws on the tensioners.</li><li>Remove the covers of the cable race way to make some room for inserting the wedges.</li><li>Insert the wedge from underneath the stepper mount and slide it into place. <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000171975/design/2024-02-06_24ae1801afdd4.png"></li><li>Push on the top of the tensioner to lock in place the wedge.</li><li>Screw the M3 x 30mm on its handle and screw it into the tensioner side.</li><li>Place the plate and add the two screws. Don&#39;t be afraid to tighten them firmly even if you ear some cracking noises coming from the plate. It&#39;s normal the first time.</li><li>Repeat those operations for the second tensioner.</li><li>Put back in place the cable race way covers.  On the K1, you might need to cut a little piece of the cover in order to be able to put it back <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000171975/design/2024-02-05_294zu8ib7rds.jpg"></li></ol>&nbsp;<h3><a href="#change_log" rel="nofollow">Change Log</a></h3>12 November 2023  Installation Guide video added15 October 2023  First release&nbsp;&nbsp;<h3><a target="_blank" href="https://ko-fi.com/henlor" rel="nofollow noopener">Want to support my work ?</a></h3>Enjoy this model? Your support means the world to me! If you love what I do, remember to like and rate the model. You can also follow me to get the latest updates.  If you wish to further help me to fuel future projects, consider <a target="_blank" href="https://ko-fi.com/henlor" rel="nofollow noopener">buying me a coffee</a>, I&#39;m literally running on those! Every cup counts and is immensely valued. ☕ Cheers!&nbsp;&nbsp;

Creality K1 XY Belt Tensioner Upgrade

creality k1

michal.tiller

*** At your own risk ;) for OrcaSlicer. It has real issues in BambuStudio *** !!! Start g-code DEPENDS on the end g-code where is cleaning of nozzle while cooling down → ready for immediate Z-homing on next start !!!!!! If the nozzle is not clean, do it manually: heat up nozzle, clean with brush while cooling down (60°C down). Ready !!!&nbsp;If filament change not needed, it starts print in 1 minute!Video: <a target="_blank" href="https://photos.app.goo.gl/kmk3PQYnH2xxEMe5A" rel="nofollow noopener">https://photos.app.goo.gl/kmk3PQYnH2xxEMe5A</a>&nbsp;Start g-code sequence:<ul><li>→ 140°C</li><li>Home /or bed leveling if checked + fast mech mode check (vibration compensation values and printer state)</li><li>/if needed, switch filament in AMS, +purge</li><li>Heat nozzle and print /start with purge line (you can remove)</li></ul>&nbsp;I lowered the z a little for better build plate adhesion:<ul><li>Textured build plate: -0.05 (originally -0.04),</li><li>All other: -0.02 (originally 0)</li></ul>End g-code sequence:<ul><li>Bed temp off</li><li>Fans ON → for faster nozzle cooling.</li><li>Cool down the nozzle 60°C and clean it each 5°C.</li><li>All OFF.</li></ul>All commented well in the g-code.&nbsp;Czech:Vyzkoušel jsem 5 různých start g-code, co jsem našel. Důkladně jsem prošel originální a okomentoval si ho. Porovnával jsem je mezi sebou. Pak jsem přepracoval ten nejlepší, co byl pro X1C, aby dělal vše, co chci na P1S.Podstatné je, že čištění trysky pro z-homing se dělá na konci tisku, aby to bylo připraveno na příště.Pokud není potřeba, nemění se filament, nedělá se bobek.Validace vibrací se dělá jen, pokud se dělá bed leveling (pokud je zaškrtnuto).Na konci to hučí, fouká, chladí a mrská chvíli tryskou. Ale je to taky docela rychlé. Vyvětrá to zároveň komoru přes filtr.

Bambu Lab P1S start g-code: 1 minute (OrcaSlicer)

bambu p1s g-code

ChipCE

Re-use most of the MK3/S to convert it into a CoreXY machine.&nbsp;<ul><li>Build volume : 250x210x210</li><li>Semi-enclosure by default. (Full enclosure parts will be added later)</li><li>Triple Z (independent or sync based on controller board) by default or dual Z(optional)</li><li>Support V6, dragon or any similar footprint hotends</li><li>Optional AUX cooling fan</li><li>Our industrial leading SnakeOil technology</li></ul>&nbsp;Visit our github for more information : <a href="https://github.com/SnakeOilXY/ProosaXY" rel="nofollow">https://github.com/SnakeOilXY/ProosaXY</a>BOM : <a href="https://docs.google.com/spreadsheets/d/1j1bnA8rNjDqpTVEdiqrsRlNeggI6PYRAoSBm1F8bvCs/edit?usp=sharing" rel="nofollow">https://docs.google.com/spreadsheets/d/1j1bnA8rNjDqpTVEdiqrsRlNeggI6PYRAoSBm1F8bvCs/edit?usp=sharing</a>&nbsp;Change logs<ul><li>2023/07/13<ul><li>New aux duct with better balance output</li><li>Add missing panel mount parts</li><li>Update BOM</li></ul></li></ul>&nbsp;&nbsp;Demo video:<figure class="media"></figure><figure class="media"></figure>

ProosaXY (MK3/S to corexy conversion)

prusa

Filip K

Greetings,&nbsp;Presented below is a side-mounted temperature tower designed for the FLSUN v400. This apparatus oversees the temperature of both the CPU (main board) and the PSU (power supply), with two units installed. It utilizes a 5V 12V 0.56" LED Digital Thermometer, drawing power directly from the main board.&nbsp;For the temperature sensor, you can find it on AliExpress at the following link: <a target="_blank" href="https://www.aliexpress.com/item/1005004591109348.html?spm=a2g0o.order_list.order_list_main.235.35c518023iNr7m" rel="nofollow noopener">https://www.aliexpress.com/item/1005004591109348.html?spm=a2g0o.order_list.order_list_main.235.35c518023iNr7m</a>&nbsp;Feel free to share your suggestions for design improvements or create your own remix.&nbsp;Best regards,Filip

Flsun V400 - PSU & CPU TempTower

v400 

m.cody.sims

Just a good Mando helmet!&nbsp;My profile doesn&#39;t have support on the inside of the helmet because I have found it didn&#39;t really help that much with the quality and it used a lot of filament. the very center of the inside will be rough because of this but it hasn&#39;t been an issue for me.&nbsp;For those wondering what I use for a face sheild I use a Hobart 770580 Face Shield Replacement Lens, Shaded from Amazon. I cut it to shape and use a little bit of hot glue along the front and near the temples. That seems to be enough. I would recommend getting air soft helmet padding for a custom fit and comfort.&nbsp;If you like my work, please consider supporting me by boosting my model or <a target="_blank" href="https://www.buymeacoffee.com/m.cody.sims" rel="nofollow noopener">buying me a coffee</a>!

Mandalorian Helmet One Piece

costplay

Kaan_B

<h3>BambuLab Starter Kit that includes:</h3><ul><li>Top Hole Cap</li><li>Side Filament Guide</li><li>Side Spool Holder</li><li>Easily Removable Chute Bin</li></ul>&nbsp;I checked most of the designs related to &#34;Side Spool Holder&#34; and &#34;Chute Bin&#34; for BambuLab P1S but couldn&#39;t find exactly what I was looking for. So based on what I have seen and what I needed, I created my own designs from scratch using the ideas of others. You can check models I am inspired from:<ul><li><a target="_blank" href="https://www.printables.com/model/244789-bambu-lab-magnetic-chute-cover-poop-management-sys" rel="nofollow noopener">bambu-lab-magnetic-chute-cover-poop-management-sys</a></li><li><a target="_blank" href="https://www.thingiverse.com/thing:6073397" rel="nofollow noopener">thing:6073397</a></li><li><a target="_blank" href="https://www.printables.com/model/375330-side-spool-holder-with-filament-guide-remix-of-bas" rel="nofollow noopener">side-spool-holder-with-filament-guide-remix-of-bas</a></li><li><a target="_blank" href="https://www.printables.com/model/408237-bambu-lab-x1c-p1p-foldable-side-spool-mount" rel="nofollow noopener">bambu-lab-x1c-p1p-foldable-side-spool-mount</a></li></ul>Note: I couldn&#39;t check if these fit on P1P or X1 as I only have P1S, so if you make it for those machines please let me know the result so I can update the description.  &nbsp;Filament:<ul><li>I suggest to use PETG or stronger.<ul><li>You can use PLA, it works as well but others will be more stronger</li></ul></li></ul> Parts:<ul><li>Top Hole Cap<ul><li>No support</li><li>No special configuration  </li></ul></li><li>Side Filament Guide<ul><li>No support</li><li>No special configuration</li><li>BOM:<ul><li>1x PC4-M10</li><li>2x M3x10  </li></ul></li></ul></li><li>Side Spool Holder<ul><li>No support</li><li>Increase wall-loop/perimeter until it&#39;s 100%</li><li>BOM:<ul><li>2x M3x8 or M3x10 (to metal spool holder)</li><li>2x M3x12 (to the printers case)</li><li>2x M3 Hex Nut  </li></ul></li></ul></li><li>Chute Bin Base<ul><li>No support</li><li>No special configuration</li><li>2 versions, 1 with honeycomb like bottom</li><li>BOM:<ul><li>1x M3x8 or M3x10</li><li>small piece of double-sided tape (optional)  </li></ul></li></ul></li><li>Chute Bin<ul><li>Big:<ul><li>Support Required (Basic)</li><li>No special configuration</li></ul></li><li>Small<ul><li>No support</li><li>No special configuration</li></ul></li></ul></li></ul>

Bambulab Starter Kit

bambu p1 y x1

le-blab.fr

Utime park for your Bambulab and your AMS PTFE guide Waste ramp AMS drying ball box Tools to help you remove cables and Ptfe More information on le-blab.fr------------------------------------------Parck utime pour vôtre Bambulab et vôtre AMS Guide PTFE Rampe à déchets Boite à billes de séchage AMS Outils pour vous aider à enlever les cables et Ptfe Plus d'informations sur le-blab.fr

Tools pack for Bambulab and AMS

Leo.w8

Introducing the Ultimate DIY Durable Tool Box – Your Next 3D Printing Project!&nbsp;Are you ready to take your 3D printing skills to the next level? I've designed a robust and versatile tool box model that you can easily print yourself, and the best part is, it's absolutely free for you to download and create at your convenience.Features:&nbsp;<ol><li>Sturdy Design: This DIY Durable Tool Box boasts a robust construction, ensuring it can withstand the rigors of your toughest projects. Crafted to last, it's built to store your cherished tools and equipment securely.</li><li>Hinged Lid: With two precision-engineered hinges, the lid opens and closes smoothly, providing easy access to your tools while keeping them safely contained when not in use. No more searching for your essentials; they'll be neatly organized and at your fingertips.</li><li>Comfortable Handle: The ergonomically designed handle ensures a comfortable and firm grip, making it easy to transport your tools to any job site or workspace. It's not only functional but also visually appealing, enhancing the overall aesthetics of your toolbox.</li><li>Customizable Fasteners: To assemble your DIY Durable Tool Box, all you need are a few standard fasteners. You'll require 2x M4x50mm screws for the handle and 4x M4x35mm screws for the hinges, which are readily available at your local hardware store. This customization allows you to choose the materials and finishes that suit your personal style and needs.</li><li>Ample Storage Space: Inside, you'll find ample storage space with customizable dividers to keep your tools neatly organized. Whether you're a professional tradesperson or a dedicated hobbyist, this toolbox is designed to accommodate your unique tool collection.</li><li>Durability and Longevity: The materials and design used in this toolbox are intended for long-term use, so you won't have to worry about wear and tear. It's a testament to my commitment to providing you with a high-quality product.</li></ol>Share Your Thoughts, I'd appreciate your ratings and reviews after you've successfully created and used this DIY Durable Tool Box. Your feedback helps me improve and inspires me to keep creating innovative designs for the 3D printing community. Your input is invaluable to me, so please share your experience with our community.Now, it's time to roll up your sleeves and embark on your next 3D printing adventure. Download this free DIY Durable Tool Box model and enjoy the satisfaction of crafting your own reliable storage solution. Say goodbye to flimsy and expensive store-bought toolboxes – build the one that perfectly suits your needs. Get started today and experience the joy of making something exceptional with your own two hands!&nbsp;For the handle 2x M4x50mm For the hinge 4x M4x35mm &nbsp;&nbsp;

Tool Box

herramientas cajas y demas

wimpel.funkeln_07

<h3>Simply another filament shelf holder.</h3>This is the first version, I am working on improvements, e.g. fixing the wooden round bars, connectors for stacking multiple shelves, etc.Print two holders per shelf unit and mount them on a sturdy wall. Then simply slide two round rods (18mm diameter) through the holes.If other diameters for the feedthroughs are desired, leave me a like and a comment and I'll upload more versions!Printed in PETG for better stability, but probably works well in PLA with the settings (please test yourself and always consider the weight to be carried).Printed with the following settings on a BL X1C in highest speed:Layer height 0.28mm Walls: 5 Filling: 25% (cubic) Support: No Brim: 4mmV2 is closed hole for rods, V6 has open holes (you can set V6 later somewhere in the middle, if you find out that the load is to heavy)----If you like my model, please leave me a like! And a picture of your Make would be great for others to see how it works.----Update: If you need a different distance between the storage bars for other coil sizes, write me a comment and I will adjust the STL. The first version is designed for 200mm spools.&nbsp;Check also the Coverplate to cover the ends of the shelf → https://makerworld.com/en/models/32662#profileId-29337&nbsp;&nbsp;<h3>Einfach ein weiterer Filamentregal-Halter.</h3>Dies ist die erste Version, ich arbeite an Verbesserungen, z.B. Fixierung der Holz-Rundstäbe, Connectoren für die Stapelung mehrerer Regale, usw.Drucke zwei Halter pro Regaleinheit aus und montiere sie an einer stabilen Wand. Schiebe dann einfach zwei Rundstäbe (18mm Durchmesser) durch die BohrungenWenn andere Durchmesser für die Durchführungen gewünscht sind, lasst mir ein Like und einen Kommentar da, ich lade dann weitere Versionen hoch!Gedruckt in PETG für bessere Stabilität, funktioniert mit den Einstellungen aber vermutlich auch gut in PLA (bitte selber testen und immer das zu tragende Gewicht beachten)Gedruckt mit folgenden Einstellungen auf einem BL X1C in höchster Geschwindigkeit:Schichthöhe 0,28mm Wände: 5 Füllung: 25% (kubisch) Support: No Brim: 4mmV2 hat geschlossene Öffnungen für die Stangen, V6 hat offene Löcher (du kannst V6 später irgendwo in der Mitte dazumontieren, falls du feststellst, dass die Last zu schwer ist)----Wenn dir mein Modell gefällt, lass mir gerne ein Like da. Und ein Foto deines Makes wäre großartig, um Anderen zu zeigen, wie du es einsetzt.----Update: Falls du einen anderen Abstand zwischen den Aufbewahrungsstangen für andere Spulengrößen benötigst, schreibe mir einen Kommentar, ich passe die STL dann an. Die erste Version ist für 200mm Spulen ausgelegt.&nbsp;Es gibt auch eine Abdeckplatte zur Abdeckung der Enden des Regals → https://makerworld.com/en/models/32662#profileId-29337

Filament Shelf Holder

para hogar

Waikikiprod

<h2>02/02/24 : a Valentine&#39;s day variation is availabl</h2><figure class="image image_resized image-style-side" style="width:32.4%;"><a href="https://makerworld.com/en/models/168156" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2024-02-02_897099cc5abb18.gif"></a></figure><h2>e <a target="_blank" href="https://makerworld.com/en/models/168156" rel="nofollow noopener">HERE </a></h2><figure class="image image_resized image-style-side" style="width:32.5%;"><a href="https://makerworld.com/fr/models/78331" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-12-12_2ae6daa740a2.gif"></a></figure><h2>This file is a variation of my <a target="_blank" href="https://makerworld.com/fr/models/78331" rel="nofollow noopener">lockable present</a> model specially dedicated to Makerworld to thank them.</h2><h2>All commercial use are reserved for Bambulab and Makerworld</h2><h2>A big thank you in particular to Sybil from the Bambu team! ;)</h2><h3> </h3><h3>A Christmas gift with an ingenious locking system !</h3><h3>Simply twist the knot to lock or unlock the present !</h3>Just need Glue the ribbons (PVC Glue recommended)No need screws.<h2><a target="_blank" href="https://www.instagram.com/reel/C0R34OFrZxP/?utm_source=ig_web_copy_link&amp;igshid=N2ViNmM2MDRjNw==" rel="nofollow noopener">Video of assembly Here</a></h2>Precautions :- do not change the first layer speed of 3mf files.- Your print bed must be completely clean.&nbsp;Advices :- Use 3D Lake Spray<figure class="table" style="width:98.21%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td style="text-align:center;"><figure class="image image_resized" style="width:77.52%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-12-12_f2e9e477e02908.jpg"></figure>All Ribbons Dual Color.3mf</td><td style="text-align:center;"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-12-12_e6ff3e5561ee88.jpg"></figure>node Dual Color.3mf</td></tr><tr><td style="text-align:center;"><figure class="image image_resized" style="width:76.15%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-12-12_9fb1ac7ad0932.jpg"></figure>half node x2 Dual Color.3mf</td><td style="text-align:center;"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-12-12_28081d35c8af6.jpg"></figure>Mechanism Mono Color.3mf</td></tr><tr><td style="text-align:center;"><figure class="image image_resized" style="width:72.81%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-12-12_7b880fadb6eab.jpg"></figure>Lid Mono Color.3mf</td><td style="text-align:center;"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-12-12_1cd9e494dee1a8.jpg"></figure>box Mono Color.3mf</td></tr></tbody></table></figure><h3>Support my work with <a target="_blank" href="https://bambulab.com/fr-fr?sscid=51k8_1qigt" rel="nofollow noopener">my Bambu Lab affiliate link</a></h3><h3>Thanks to you and your downloads, this 3D model is free! Thank you so much !!! &lt;3</h3>Follow me on<a target="_blank" href="https://www.instagram.com/waikikiprod/" rel="nofollow noopener"> Instagram</a> / <a target="_blank" href="https://www.tiktok.com/@waikikiprod" rel="nofollow noopener">TikTok</a> / <a target="_blank" href="https://www.facebook.com/waikikiprod" rel="nofollow noopener">Facebook</a> / <a target="_blank" href="https://beacons.ai/waikikiprod" rel="nofollow noopener">Beacons</a>Discover My Best 3D Models<figure class="table"><table><tbody><tr><td><figure class="image"><a href="https://makerworld.com/fr/models/14009?profileId=13993" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-09-11_49db957f2d46d.png"></a></figure><a target="_blank" href="https://makerworld.com/fr/models/14009?profileId=13993" rel="nofollow noopener">X1C Keychain</a></td><td><figure class="image"><a href="https://makerworld.com/fr/models/13847?profileId=13645" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-09-11_03b57abb0262f.jpg"></a></figure><a target="_blank" href="https://makerworld.com/fr/models/13847?profileId=13645" rel="nofollow noopener">Axe Magnet</a></td><td><figure class="image"><a href="https://makerworld.com/fr/models/13841?profileId=13635" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-09-11_d454006b5cde4.png"></a></figure><a target="_blank" href="https://makerworld.com/fr/models/13841?profileId=13635" rel="nofollow noopener">Tank toy - Print in place</a></td></tr><tr><td><figure class="image"><a href="https://makerworld.com/fr/models/13159?profileId=13163" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-09-11_ec02bcb1e833b.jpg"></a></figure><a target="_blank" href="https://makerworld.com/fr/models/13159?profileId=13163" rel="nofollow noopener">Foaming Soap Dish</a></td><td><figure class="image"><a href="https://makerworld.com/fr/models/13723?profileId=13450" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-09-11_e177dc4e45a09.jpg"></a></figure><a target="_blank" href="https://makerworld.com/fr/models/13723?profileId=13450" rel="nofollow noopener">The console of your childhood</a></td><td><figure class="image"><a href="https://makerworld.com/fr/models/13846?profileId=13640" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000090640/design/2023-09-11_2d9999d3ea301.png"></a></figure><a target="_blank" href="https://makerworld.com/fr/models/13846?profileId=13640" rel="nofollow noopener">The Ultimate Fidget Avocado Keychain</a></td></tr></tbody></table></figure>&nbsp;

Lockable Present - MakerWorld Edition

impresiones chulas

LaurienzuDesign

<figure class="media"><div data-oembed-url="https://youtu.be/tiv2-XtsNCY"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/tiv2-XtsNCY" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><h3>INTRODUCTION</h3>This project was born in the spirit of providing a functional and optimized mount for the community of Sapphire users and it's the result of more than 200 hours of design, testing and reiterating in my free time. I will do my best to maintain and improve the project with incremental upgrades, but maintenance takes time and effort. If you wish to support my work and motivate me please consider to buy me a coffee ☕ <a target="_blank" href="https://ko-fi.com/F2F28XZ5E" rel="nofollow noopener">Support me on Ko-Fi</a> For help, discussions and other useful links <a target="_blank" href="https://linktr.ee/laurienzudesign" rel="nofollow noopener">Click Here</a> Thank you very much for your support!!! ❤️<h3>THE DIAMOND MOUNT 💎</h3>Designed with “form follows function” in mind, the goal was to have a mount with optimized cooling, totally hidden cables, bowden, Sherpa mini or Sherpa micro direct drive support, integrated belt tensioner, an ADXL345 mount for Klipper and more. It is tailored around the geometry of Two Trees Sapphires printers but can be mounted on any MGN12H rail printer if belt path is adaptable.Diamond mount currently supports E3D V6, V6 Volcano and similars, Dragon with a groove or rigid mount, Phaetus Dragonfly, Mellow NF-Crazy (mosquito) and more!If you like my design, please rate it and post your make! Any comment and suggestion to improve the project is really appreciated, I will release future updates in this page.Many thanks to my friend BostonGeorge_76 and to my others beta testers friends for helping me to test and improve the mount.&nbsp;For assembly please read the <a target="_blank" href="https://docs.google.com/presentation/d/1-Ee2e8QgYi-yDCYDKD2s8ehqo0UsH6LD/edit#slide=id.p1" rel="nofollow noopener">ASSEMBLY GUIDE</a> carefully!<h3>FEATURES</h3><ul><li>Low poly diamond-like design</li><li>Designed for 3D printing, all overhangs and tolerances are adjusted to have a perfect fit and to be printed without supports (you just need good cooling and bridge tuning).</li><li>Modular support for BL-touch and P.I.N.D.A. probe, you can adapt other probes using the faceplate STEP file</li><li>Natively compatible with Sherpa Mini and Micro, compatbile too with BMG in direct drive, Orbiter V1.1, V1.5, V2, LGX Lite, TBG Lite with the use of the adapting plate</li><li>An actual belt tensioner, you can fine tune the tension of each belt simply with an M3 screw (turning clockwise tight the belt and anticlockwise to release tension)</li><li>Belt perfectly parallel for both Pro/Plus V1 and Plus V1.1 with dedicated belt clamps</li><li>Removable rear belts blocks (you can disassembly the mount without losing the tensioning setting)</li><li>Brass inserts for structural fittings, 2 versions of top and main frame available for 5mm and 4.6mm diameter inserts (for extra additions like fans and ADXL there are calibrated holes for screws, to keep a lightweight solution)</li><li>Tilted part cooling fans, resulting in a smaller attack angle inside the duct, and improvements over the laminar flow</li><li>Ducts designed with CFD simulations (modeled on GDStime fan curve) to optimize flow without loosing pressure. Real tests were done to match the simulations</li><li>X axis limit switch hidden and integrated in the top frame (sensorless homing supported with dummy endstop)</li><li>Internal cables management (no cables are visible) with routes and guiding tube</li><li>Low weight thanks to the removal of all the original metal plates, it can reach 130g in the lightest bowden configuration</li><li>You gain about 5mm of Z but you will lose a few mm on X and Y (less than 10 in total) so if you don't like this please don't use it</li><li>The space to fit the ADXL345 accelerometer, used for Klipper, is embedded in the main frame and positioned in the center of gravity to avoid misreadings</li><li>Hidden hotend fan maintaining a proper flow</li><li>Hidden bed probe integrated in the faceplate (no LEDs disturbing the webcam)</li></ul>Required parts and screws (Bill of materials): <a target="_blank" href="https://docs.google.com/spreadsheets/d/1BW-cE3cIfOesapLvuGciVe0dl3kaHlzK0vwRGYZZXz4/edit#gid=0" rel="nofollow noopener">CLICK HERE</a>Others suggested parts and upgrades: <a target="_blank" href="https://docs.google.com/spreadsheets/d/1BW-cE3cIfOesapLvuGciVe0dl3kaHlzK0vwRGYZZXz4/edit#gid=152074595" rel="nofollow noopener">CLICK HERE</a>&nbsp;And, if you want to buy another printer for this mount (😂):<ul><li>Sapphire Pro (SP-3) <a target="_blank" href="https://s.click.aliexpress.com/e/_9Hg0pZ" rel="nofollow noopener">Aliexpress</a></li><li>Sapphire Plus (SP-5) suggested! <a target="_blank" href="https://bit.ly/3jwpGEe" rel="nofollow noopener">Aliexpress</a></li></ul>I hope you will enjoy this project as much as I do. Please consider supporting my work by donating so I can continue creating for you.Thanks a lot 😊 Please read the <a target="_blank" href="https://docs.google.com/presentation/d/1-Ee2e8QgYi-yDCYDKD2s8ehqo0UsH6LD/edit#slide=id.p1" rel="nofollow noopener">ASSEMBLY GUIDE</a> carefully before asking help!&nbsp;Have fun and... shine bright like a diamond! 💎&nbsp;<figure class="media"><div data-oembed-url="https://youtu.be/3m3Z6EEORzQ"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/3m3Z6EEORzQ" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><figure class="media"><div data-oembed-url="https://youtu.be/i7cHbiPYaa4"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/i7cHbiPYaa4" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>