user_310056041

xallex digital design

Fallout Fusion Core / Stash Container Desk / Ornament Replica / Cosplay Accessory Multi-part locking stash container / Desk Ornament Replica of the Fusion Core from the popular game Fallout  <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000430340/design/2024-04-17_82adf2aefef13.png"></figure> Screws: x4 M2 x 4mm Stainless Steel Hex Socket Head Cap Screws (Attach bottom) – (<a target="_blank" href="https://amzn.to/3Wgm5Ou" rel="nofollow noopener">https://amzn.to/3Wgm5Ou</a> or <a target="_blank" href="https://amzn.to/49TxXta" rel="nofollow noopener">https://amzn.to/49TxXta</a>) x1 Black M3 x 6mm (Attach knob) – (<a target="_blank" href="https://amzn.to/4aP4hPd" rel="nofollow noopener">https://amzn.to/4aP4hPd</a>) Material: Yellow - Hatchbox PLA <a target="_blank" href="https://amzn.to/3U9sl8c" rel="nofollow noopener">(https://amzn.to/3U9sl8c</a>) Red - Hatchbox PLA (<a target="_blank" href="https://amzn.to/4b52FRa" rel="nofollow noopener">https://amzn.to/4b52FRa</a>) Black - IIIDMAX PLA+ (<a target="_blank" href="https://amzn.to/3wcbjhK" rel="nofollow noopener">https://amzn.to/3wcbjhK</a>)  Glow - Duramic 3D PLA (<a target="_blank" href="https://amzn.to/3xUMPdl" rel="nofollow noopener">https://amzn.to/3xUMPdl</a>)

Fallout Fusion Core Stash Container Desk Replica

To Print

DesignCraft

DISCLAIMER: Print profiles NOT created by DesignCraft may contain outdated model versions or suboptimal slicer settings. Use at your own risk! I have no control to moderate or remove these third party print profiles.&nbsp;The Overture v2 print profile is the original print profile updated with a new model. It's a redesign based on user feedback and also uses about 40% less material. Please refer to the Disclaimer above and also please read the Considerations section below.&nbsp;Description:&nbsp;This adapter system wraps the edges of an OVERTURE 1kg 199x66mm cardboard spool in order to:<ul><li>provide smooth rotation within a Bambu Lab AMS</li><li>prevent carboard debris from depositing within a Bambu Lab AMS</li></ul>Features:<ul><li>Reusable</li><li>OVERTURE nameplate for easy identification when reusing</li></ul>Instructions:<ul><li>Print this model twice for a single spool</li><li>Affix one spool ring adapter on each side of the OVERTURE spool</li><li>See attached photos</li></ul>Considerations:<ul><li>Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.</li><li>Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.</li><li>AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">AMS Lid Riser</a> which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on <a target="_blank" href="https://makerworld.com/en/u/243407759" rel="nofollow noopener">my profile</a> or directly here: <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">https://makerworld.com/en/models/33133</a></li></ul>

To Print

Printed