栗子

xuhao3e8

Here shows my own design, the Aurora, or 极光. It's an incredibly cool FPV cruiser that offers high speed and agility.<img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_07413e4f4b99.png">The design of Aurora is inspired by the IJN J7W Shinden and XP-55, with the addition of modern aircraft elements.Including full-span canard, strakes (although they serve mostly as decorative elements), and winglets.It comes with a <a target="_blank" href="https://www.printables.com/model/567442-dji-o3-air-unit-ptz" rel="nofollow noopener">servo gimbal (included in this model, remix from FLY_101</a>) and cooling system for the DJI O3. So great if you wish to use a headtracker on it.&nbsp;The flying speed is fast, with a cruising speed of 70kph (20m/s), and it can easily reach 100-130kph, pulling 3-4g maneuvers. A large area is required for flying, and it is completely unsuitable for park flying. When the flying speed exceeds 100kph, noticeable vibrations occur in the gimbal, severely affecting the flying experience, necessitating targeted optimization in the design. Here are some basic details:<ul><li>Wing Span: 1030mm</li><li>Weight (4s 18650, no gimbal & FPV system): ~1000g</li><li>Weight (with 4s18650 battery, with gimbal & FPV system): 1170g</li><li>Estimated endurance time: 30-45 minutes (theoretically, still testing)</li><li>Cruising speed: 20m/s-30m/s, 70km/h to 110km/h</li></ul>Tested avionics:<ul><li>Flight Controller: SpeedBee F405 Wing with BZ182 GPS.</li><li>ESC: Any 30A ESC is OK</li><li>FPV system: DJI O3</li><li>Servo: Kingmax KM0940MD*4 (for flight control), and GDW DS014MG*2, 280deg/180deg (for servo gimbal)</li><li>Motor: SunnySky X2216 KV1400</li><li>Propeller: APC/Gemfan 8*6-9*6, this may push you to 100kph or faster.</li><li>Battery: Sony VTC6 18650 4s1p</li></ul>Extra components:<ul><li>Carbon fiber pole:<ul><li>2*6x4x550</li><li>1*6x4x585</li><li>1*6x4x935</li><li>3*3x250</li><li>1*3x150</li></ul></li></ul>Four 6mm (diameter) x3mm (height) magnets for battery and flight controller canopy.&nbsp;The core design concept of Aurora includes:<ul><li>Appealing aesthetics</li><li>Decent endurance time</li><li>Relatively high speed.</li></ul><h2>Printing</h2><h3>Suggest print material:</h3>Fusrock/Bambu PLA Aero.I use Bambu PLA-Aero white for Wing, and FuskRock Gray PLA Aero for Fuselage. Use PLA-Aero from two manufacturer just because colors.<h3>BE CAREFUL GO SETUP CORRECT PRINTING SETTINGS FOR FILAMENTS!</h3>Default setting is for PLA-Aero, change it according to your own filaments. Strongly suggest print Aurora with PLA-Aero.<h3>3D printer</h3>Tested on Bambu Lab X1CC, suggest Bambu Machines with size=256mm<h2>Print profiles:</h2>Fuselage, wings and extra component are placed in different print profiles. They have different slice settings.<h2>Flying Video:</h2>(Click to watch if you see video unavailable)<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=-W8qLUvWbIY"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/-W8qLUvWbIY" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>对于中文用户，可以观看bilibili和简介中的介绍:<figure class="media"><div data-oembed-url="https://www.bilibili.com/video/BV1xj411W7ry/"><div class="ck-media__wrapper" data-oembed-url="https://player.bilibili.com/player.html?bvid=BV1xj411W7ry&autoplay=0&poster=1"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://player.bilibili.com/player.html?bvid=BV1xj411W7ry&autoplay=0&poster=1" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>&nbsp;Gimbal system of Aurora is remix from <a target="_blank" href="https://www.thingiverse.com/thing:6193480" rel="nofollow noopener">https://www.thingiverse.com/thing:6193480</a> by <a target="_blank" href="https://www.thingiverse.com/FLY_101" rel="nofollow noopener">FLY_101</a>.You may also use <a target="_blank" href="https://www.printables.com/model/265534-dji-2-dof-gimbal-for-air-unit-camera/files" rel="nofollow noopener">this gimbal on Aurora</a>&nbsp;<h2>Center of Gravity</h2>Flight with current CG setup (the CG icon) is too stable. You may try the following CG at read line, this is optimal CG point according to my latest CFD results and flight test.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-28_43baa86270ef2.png"></figure>&nbsp;<h2>Donation to help me!</h2>Testing and releasing these model aircraft designs is neither easy nor cheap. It requires a significant investment of time and effort. The development cost of this airplane exceeds $1500, and that's not even taking into account my time. If you find my designs practical and useful, please consider making a donation to support my work. Your contributions will greatly assist me in continuing to develop these model aircraft, feel free to buy me a coffee by clicking follow button.<a target="_blank" href="https://www.buymeacoffee.com/xuhao3e8" rel="nofollow noopener"><img src="https://cdn.buymeacoffee.com/buttons/v2/default-yellow.png" alt="Buy Me A Coffee"></a>测试和发布航模并不便宜，这架飞机的开发成本超过万元，并且会花费非常多的时间和精力，如果你觉得我的设计非常实用，请捐款支持我，这将对我能够继续开发航模产生很大的帮助：<figure class="image image_resized" style="width:37.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-27_0ec676d5a355f.jpg"></figure><h2>Build Logs</h2>Build logs (in Chinese) for Aurora is available on <a target="_blank" href="https://xuhao1.notion.site/Aurora-1100-8851f194908a4648b1bb22ffa9a7a9cb?pvs=4" rel="nofollow noopener">my notion site,</a> this contains every detail you may want to know about Aurora.<h2>Update since upload</h2>2023/12/21: Update to integrated vertical tail and rudder: do not need manually install hinge. I put the old design of vertial tail in supported files.2023/12/23: Missing fuselage part is added to fuselage.3MF. Servo gimbal is also added to extras.3MF with original author's approval.<h2>Some details</h2>More details will be adding later.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_f29fd3e4a7b4a.png"></figure><figure class="image image_resized" style="width:58.84%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-22_d5a12ad1a93b4.jpg"></figure><figure class="image image_resized" style="width:56.85%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_3cd4e9ee5e9cc.jpeg"></figure><figure class="image image_resized" style="width:62.08%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_b01c294f7d8c7.png"></figure><figure class="image image_resized" style="width:53.14%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_12f6f67c86d8d.jpeg"></figure><figure class="image image_resized" style="width:54.3%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_d359d7203dc83.png"></figure><figure class="image image_resized" style="width:55.2%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_f582829daf851.png"></figure>

Aurora: Fixed-Wing FPV Cruiser

航模

NUKDDD

Legend says that some chickens and bunnies had babies and that's where these adorable little hole-y eggs came from. People would go hunt for these eggs every spring, thus came the holiday called Easter…I made that up, it's actual about a bunny waking up after a long nap and losing the race to the tortoise and became an egg.&nbsp;Please give a 👍 if you like it, even if you don’t download it, it’ll help others discover it 😊Commercial rights available for all my designs at <a target="_blank" href="https://www.patreon.com/NUKDDD" rel="nofollow noopener">https://www.patreon.com/NUKDDD</a>&nbsp;These eggs will look great day and night by themselves or next to other decors.&nbsp;<a target="_blank" href="https://shrsl.com/4gf88" rel="nofollow noopener">Designed to fit Bambu Lab's Lamp Kit, available in the online shop.</a>&nbsp;Printed with Bambu's <a target="_blank" href="https://shrsl.com/4gfvl" rel="nofollow noopener">Basic</a> and <a target="_blank" href="https://shrsl.com/4gfae" rel="nofollow noopener">Matte PLA</a>&nbsp;No support, easy assembly, big one compatible with Bambu Lamp Kit 001 and small one for tea lights up to 40mm in diameter. Standard setting, except for the bases, they all have fuzzy skin turned on, default setting. You can support me by using my affiliate link to purchase <a target="_blank" href="https://amzn.to/3PxD8HO" rel="nofollow noopener">the LED candle</a> I purchased in my video and photos. I may earn a small commission.&nbsp;All you need is to bring your own light, nothing else is needed, like most of my designs. Check them out in my profile!&nbsp;Disclaimer: This model is part of the Creator Program, When you purchase the Lamp Kit 001 or filament through the links provided, creators may earn an affiliate commission as a reward of their work. (The creator program is currently in the trial phase. The application is not yet open to public.)

Easter Bunny Egg Lamp 

摆摊

LucMeister

Keeping small screws and other bits&pieces tidy and organized is a tedious task, and even though lots of them ship in plastic boxes it's a pain when they have thirteen different sizes and just stack very badly. I see a lot of recommendations (and printable accessories) for <a target="_blank" href="https://amzn.to/3tDQ1bK" rel="nofollow noopener">Stanley Fatmax organizer boxes</a> - they look dope and I dig them, but a single box of these costs roughly 25€ in my location; printed inserts not included. That's a bit of a hefty price if you need a few of them.&nbsp;history. Last year <a target="_blank" href="https://www.printables.com/model/380208-dividers-for-werckmann-storage-boxes" rel="nofollow noopener">I saw a model on Printables</a> which used super cheap (99 Cents!) <a target="_blank" href="https://www.action.com/de-at/p/2547795/werckmann-aufbewahrungsbox/" rel="nofollow noopener">storage boxes/organizers from the ACTION Store Chain</a> across Europe (originally from the Netherlands); these sometimes go under the Werckmann brand name and sometimes are only generic (see image), the inner layout is the same though; just make sure it's the 20 x 16 cm version. Those models were a bit wasteful and too thick (and therefore printed slowly) in my opinion, so I gave the idea a spin and designed them myself. boxes. The outer walls are thin as they are carried by the organizer box itself, the inner dividers are three walls thick (0.4mm nozzle) which is plenty strong for the application. The bottoms are chamfered to get things out easier, but as you can see on the photos the bottom is chamfered as well to save a lot of filament and printing time.There's a total of 36 different boxes and layouts, there's a lot of ways you can divide these :) some of the corner-pieces are also available in different orientations so you can direction-match an upper and a lower corner, see the photos for examples. I also added boxes without dividers, in case you want to look-match other compartments or just want the chamfered bottom. As naming these are hard with all the different divisions, I only wrote the total number of compartments and labelled them ABC, please have a look on the exact differences on the STL files.&nbsp;I also made a shelf specifically for these boxes (see photos), <a target="_blank" href="https://makerworld.com/models/134601" rel="nofollow noopener">you can find it here</a>.The specialized inlay for TS-100 tips from CNCKitchen <a target="_blank" href="https://makerworld.com/models/136915" rel="nofollow noopener">can be found here</a>. printing advice. The provided printing profile contains the settings I recommend for printing (0.28mm because they really don't need to be any finer), but it's just sample files; it's virtually impossible to provide all combinations you might want, so please fill the slicer with the exact models you need :)Depending on the pieces you want to print, one fully assembled organizer box will need 65g to 108g of Filament, which translates to 1.30€ to 2.16€ at a Filament price of 20€/kg. So for roughly 3€, you have a fully equipped organizer! If you don't care as much about looks, it's also a good way to get rid of nearly empty spools of filament, as you can see in the orange-green example in my photos :)

Werckmann / ACTION Organizer Box Inlays

工具

极品

底板需要稍微打磨一下间隙，卡口设计无需额外配件打印即可组装，其他位置都已添加公差，皮筋位于炮筒内两侧绑在炮闩上，炮闩后部栓绳上膛用，炮弹尾翼是圆的问就是方便出膛，组装看爆炸图很简单，俯仰角度螺杆调整，球头直接卡在炮尾。&nbsp;&nbsp;The bottom plate needs to be slightly polished, the bezel design can be assembled without additional accessories printing, and other positions have been added tolerances, the rubber band is located in the barrel on both sides of the gun bolt, the rear bolt rope is loaded for loading, the shell tail is round, which is easy to assemble and see the explosion diagram, the pitch Angle is adjusted, the ball head is directly stuck in the tail of the gun.<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000051653/design/2023-10-28_ebfebdd7dc1eb.gif">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000051653/design/2023-10-28_7f0a872748b43.gif"><figure class="media"><div data-oembed-url="https://www.bilibili.com/video/BV1NC4y1J7dQ/?spm_id_from=333.999.0.0&amp;vd_source=303d776156c57c5fb30e4a30f5678ab0"><div class="ck-media__wrapper" data-oembed-url="https://player.bilibili.com/player.html?bvid=BV1NC4y1J7dQ&amp;autoplay=0&amp;poster=1"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://player.bilibili.com/player.html?bvid=BV1NC4y1J7dQ&amp;autoplay=0&amp;poster=1" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>

cannon，皮筋大炮，萝卜炮，红夷大炮大将军炮Red cannon, General cannon

玩具

zeddiArts

Fixes filament feeding issues.&nbsp;My AMS always jammed the filament at this point.I used a screw from the spare parts to attach it.

Bambu Lab Curved Holder for left AMS Hub PTFE Tube

拓竹

Rubicon

I made this as a night light for a kid's room and it came out awesome. You will need the following.&nbsp;Blue, Red, Yellow and Black PLATextured PEI Build PlateWhite LED light strip. I used this from Amazon www.amazon.com/dp/B0B7P65KWM?ref=ppx_yo2ov_dt_b_product_details&th=1Some superglue to hold things together.&nbsp;Enjoy and share your makes.

Superman Lightbox Logo / Night light

装饰品

Nils Kal

Want to have a cool place to put your headphone? Print yourself this nice retro item!All parts are seperated so you won't need a AMS, just print them in your desired colors.Assembly is pretty straight forward, just put all pieces together. May use a bit of glue.&nbsp;Happy printing!NK&nbsp;&nbsp;This work is licensed under the 'Creative Commons NonCommercial' license. Please do not sell any physical or digital copies of it.

航模

摆摊

工具

玩具

拓竹

装饰品

游戏