star_dust

maruel

Leverage the Aux Fan and heated bed in your X1/X1C/P1S to act as a filament dryer.<h2>Printing</h2>The design is printing friendly (PC with 65° overhang or ABS with 50° overhang) and designed to maximize speed, minimize filament usage while having good thermal isolation properties.You should be able to get good enough results even if your roll is moist; permitting you to bootstrap your cooking.Print with ABS or PC. Do not use PLA or PETG because their melting temperature is too low.An option is to do the first with ABS so you can cook your PC. Then print it again in PC. That said, my ABS cover was able to sustain 95℃ bed temperature overnight just fine. As a matter of fact, the Bambulab Reusable Spool is made of ABS!The cover is designed for the AMS spool sizing, which is 202 mm in diameter and 70 mm wide.<h3>Print settings</h3>0.4mm nozzle, 0.20mm Standard, 10% infill, infill direction: 0°, rectilinear infill (20min faster than grid), Seam position Nearest. Optionally use brims if ABS, not necessary with PC.Use &#34;Auto Orient&#34; then &#34;Arrange all objects&#34; with &#34;Auto rotate for arrangement&#34; checked. It should put the cover at 45° on the bed.If not, place the cover top down at 45° on the bed by rotating 45° on the Z axis.Printing time is 5½h~6½h and uses less than 220g of filament.<h2>Usage</h2><h3>Cooking</h3>Do not use the Dry filament program in the printer. We can use slightly higher temperatures for better drying because of the airflow. ♨️&nbsp;Tested with both ABS spools (Bambulab) and cardboard spools (Overture, Polylite).<ol><li>Put the high temp plate.</li><li>Adjust the plate Z height at the level where the cover&#39;s exhaust is at the Aux fan.</li><li>Put the Aux fan and Chamber fans at 30%.</li><li>Increase the bed temperature to the desired level (between 70℃ and 95℃). See <a target="_blank" href="https://maruel.ca/post/bambulab_filaments/" rel="nofollow noopener">https://maruel.ca/post/bambulab_filaments/</a> for a one pager including bed temperature for popular filaments.</li><li>Let your spool cook overnight. Turn mid-cook if you are insomniac.</li></ol><h3>After cooking</h3>To cool down the plate, put the Aux fan and Chamber fans at 100% and press Home. Leave the door open and the bed should cool down within 3 minutes or so.Don&#39;t forget to switch plates if you print PLA or TPU.Note that if you take a high temperature cooking filament and directly put it in the AMS right after, the filament will have the AMS gears deform the filament a little. It doesn&#39;t seem to be a problem.<h2>Contact</h2>The design is fully parametric. Contact me if you want different sizes, either smaller or larger, or want to sell printed versions.

Filament drying cover for X1C/P1S

3d打印机相关工具

SaVo3D

<h2>This my remote control holder with 3 departments!</h2>You no longer have to look for the remote control all over the living room. Store them at your table in this holder.&nbsp;I also made a version with 4 compartments: <a target="_blank" href="https://makerworld.com/en/models/153970#profileId-168273" rel="nofollow noopener">https://makerworld.com/en/models/153970#profileId-168273</a>&nbsp;The print is possible without AMS! The body and side walls are on separarate plates.After printing, simply slide in the walls. No gluing necessary!<img src="https://makerworld.bblmw.com/makerworld/draft/451483/2024-01-23_e6b4c3bece85.png">&nbsp;If necessary, cut off a little bit of the edges as shown in this picture:<img src="https://makerworld.bblmw.com/makerworld/draft/451483/2024-01-23_85c52eb6e657b.png">&nbsp;Print instructions:<ul><li>layer height 0,20mm</li><li>3 wall loops</li><li>top/bottom shells 4 layers</li><li>top/bottom shell thickness 0,80mm</li><li>sparse infill 10%</li><li>sparse infill pattern “gyroid”</li></ul>Before printing, make sure your build plate is clean and apply some adhesive. Wash the build plate with oil free soap and wipe it off with some paper towels. For build plate adhesion, apply a thin, even coat of your preferred adhesive. I repeat the process every 5-6 prints.Before printing, make sure your build plate has a decent adhesion. Aftermarket plates like the ones from Alibaba haven’t good adhesion. Curling will probably occur if you don’t use original build plates! Bad build plate adhesion is not related to the model or the design!&nbsp;Please have a look at my other models: <a target="_blank" href="https://makerworld.com/en/u/1597610120" rel="nofollow noopener">https://makerworld.com/en/u/1597610120</a>If you were satisfied with the model and the print, leave me a like, i would appreciate it. Thank you in advance!

Remote control holder 3 departments

life

pbbence1994

My next kit card is based on a Red Bull Air Race MXS-R plane. Cut the parts out with pliers, nail sissors or hobby knife. The assembly is easy and self explanatory. The parts should fit togedhter tightly, but you can always use a bit of super glue to secure the parts together. Stay tuned for more Air Race planes! The pylon display will be also available to download soon check out my profile. Have fun printing it!

Air Race plane kit card (MXS-R Breitling)

eds_3d_shop

Working on such designs takes a lot of time and if you like my work and want to support me - please print my “Designer” printprofiles! It will help me to design more! Thank you in advance!🙏&nbsp;It was time to replace my activated carbon filter again and I didn't feel like ordering and waiting again... I found a really nice model/remix for refillable charcoal /activated carbon filter for BambuLab printers at printables (Thanks to Skywarrant! :-) That suited me almost perfectly… But I had to change a few things so that I'm completely satisfied with it! :-) And I wanted to share the remixed version with you!&nbsp;<figure class="image image_resized image-style-align-left" style="width:26.74%;"><img src="https://media.printables.com/media/prints/569798/rich_content/dfdf9524-1051-4af2-9336-f730faa20a61/image-19-10-23-03-22.jpeg#%7B%22uuid%22%3A%22620154cb-9c24-4aae-887a-d95673dc0f14%22%2C%22w%22%3A750%2C%22h%22%3A1063%7D"></figure>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Here in video, I show how to change the filter material (activated carbon and HEPA!) with the help of this cool box!<a target="_blank" href="https://www.instagram.com/p/CyY9BXIr_8r/" rel="nofollow noopener">https://www.instagram.com/p/CyY9BXIr_8r/</a>&nbsp;<h4> </h4><h4> </h4>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<h4>My changes:</h4><ul><li>The lid has got 2 slits to be able to open it more comfortably - take a look at the pictures!</li><li>The tab on the lid is now more solid, so it can't break now</li><li>scaled down to 98% for better, easy fit.</li><li>main box got carbon logo and lettering ;-)</li><li>extra variant of main box stl with tabs for better adhesion (take this for ABS/ASA! ;-), just cut off these small tabs with the cutter after printing.</li></ul><h4>Print Instructions:</h4>Quality:<ul><li>layer height: 0.2mm</li></ul>Strength:<ul><li>only one wall on top surfaces: off</li><li>only one wall on first layer: off</li><li>wall loops: 5 (only for “Activated_Carbon_Filter_Bottom_with_Tabs.stl”: 9 Walls!)</li><li>top shell layers: 0</li><li>bottom shell layers: 0</li><li>sparce infill density: 30% - 50% (im prefer 50% - see on pictures)</li><li>sparce infill pattern: Triangles</li><li>Infill/wall overlap: 20%</li><li>Infill combination: off</li></ul>Speed:<ul><li>first layer: 10-20mm/s</li><li>first layer infill: 10-20mm/s</li></ul>Filament: take better ASA/ABS or at least PETG - for better temperature resistance!Good and safe source for activated carbon (or just search for “Nevermore Carbon”): <a target="_blank" href="https://github.com/nevermore3d/Nevermore_Micro" rel="nofollow noopener">https://github.com/nevermore3d/Nevermore_Micro</a>&nbsp;— ! —&nbsp;Thanks for downloading, rating in advance and please don't forget to like this model! ;-)<h3>Take a look at my another very helpful designs for X1/P1P/P1S/A1/A1mini:</h3><figure class="image"><a href="https://makerworld.com/en/u/4051934936" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/393323/2024-01-12_00009ce9c82bf.png"></a><figcaption>🔗<a target="_blank" href="https://makerworld.com/en/u/4051934936" rel="nofollow noopener">Eds_3D_Shop designs on MakerWorld</a> 🔗</figcaption></figure>&nbsp;If you like my work and want to support me - please follow me and if you want - you can buy me a coffee! <a target="_blank" href="https://linktr.ee/eds_3d_shop" rel="nofollow noopener">https://linktr.ee/eds_3d_shop</a>Thank you for your support and.. happy printing!Ed ;-)&nbsp;&nbsp;

3d打印机相关工具

life

toy

p1s改造