扯一路的蛋

Brandido02

The rims and center ring are straight from Bambu's spool. And interchangeable with it. It is designed for Bambu's refill spools. But I have found that Elegoo spools also fit perfectly on it. Also Overture and Polymaker spools fit but are a bit loose, but they fit perfectly over the center rings of Bambu and Elegoo spools. So, I use them as spacers. Let me know if you try it with any other brands!I recommend PLA because it is a lot stiffer than PETG.&nbsp;03/24/23 - I've got multiple requests, so I uploaded a version 2.3 and 3.3 that remove the little notch on the inner ring. I left print profiles with versions 2.2 and 3.2 that still have the notch for Bambu spools. Note, I think the notch is important because it locks the cardboard inner ring so it doesn't spin free of the spool. &nbsp;12/14/23 - WOW 7K Downloads!!! Some folks asked for a filament scale, Soooo here is v2.2 and v3.2!!! The left side of both have a filament scale. The right side is unchanged.&nbsp;11/19/23 - Here is v2.1 and v3.1!!! The only difference is I added a 2mm hole in the Left side of the center ring for filament to be inserted when respooling. Though respooling isn't what I usually do. I actually have found that the cardboard center of other spools fit right over the center of this spool. Specifically, Elegoo fits perfectly. you just need to nip out a little notch. I have also done it with Overture and Polymaker. but their center rings are a little bigger and so are a bit loose. But, the center ring of an overture spool fits snugly right over the center ring of an Elegoo spool, which fits snugly over the center ring of this Bambu spool!&nbsp;10/19/23 - Wow! 3K downloads! Here is Version 3! it uses less filament and takes less time. But it may not be as strong. I have been testing it now for a couple weeks without any problems.&nbsp;9/29/23 - Uploaded v2. I completely remade the spool using Bambu's newest spool. The rims are completely smooth now.&nbsp;Here is a remix of Bambu's Filament spool but with hexagons to use far less filament without sacrificing strength.The rim filament holes are also angled so as not to introduce a sharp bend into the filament. Also, there are more of them around the rim.This is interchangeable with the original Bambu rims.&nbsp;Note: the spacing shim goes on the inside of the spool to lock the two halves together. Though I haven't needed it because they lock together pretty tight. But Bambu recommends it, so I included it.&nbsp;Why hexagons? Because hexagons are the best-agons!&nbsp;Notice: Print profiles NOT created by Brandido02 may contain outdated model versions or suboptimal slicer settings. Use at your own risk! I have no control over these third-party print profiles.

Bambu Reusable Hex Spool

工具

Sevro

Update: 08.10.2023I added base with holes for M3 Screws. Use it when pins in your standard Base not fit well or broke down when printed.&nbsp;OverviewI present my my ultimate plane launcher.Easy to print and assemble. You have to only fold you favourite paper plane, load, aim and shoot it to fly. You need to only 3 rubber bands to have fun with it. One small for trigger and two larger for launcher (one for each side). Launcher is projected to assembly without screws and glue but your clearence may be different than mine. If somewhere cover don't fit correctly simply use glue to fix cover to base. After proper assembly you won't have to look inside. Rubber inside handle, stays for very long. Mine didn't break yet. Rubber bands on launcher can be strech in three position depends on rubbers size and desired force.Warning: Shoot only with a loaded launcher. Shooting without a load can damage the "barrel". The occurrence of damage depends on the force of the rubbber bands.&nbsp;To print “base” and “trigger middle” use supports for rubber bands hooks. ( I often forgot about that but despite this prints went well )Below is simple schematic of assembly.<figure class="image image_resized" style="width:82.8%;"><img src="https://makerworld.bblmw.com/makerworld/draft/75491/2023-08-14_hnasrabhm0z0.jpg"></figure>&nbsp;To load correctly, the trigger must be in the up position. Often you have to set it with your thumb in the right position as in the video below&nbsp;Loading looks like that<figure class="image"><img src="https://media.printables.com/media/prints/415098/rich_content/7d798460-cad5-42ab-960a-c535ea28eb20/giphy.webp"></figure><figure class="image"><img src="https://media.printables.com/media/prints/415098/rich_content/c065fda1-dfa9-4596-a8ae-e78fc4bd9c7b/giphy.webp"></figure>And launching<figure class="image"><img src="https://media.printables.com/media/prints/415098/rich_content/8acfd9e7-f993-4ec8-970c-ed1d5692a655/giphy-2.webp"></figure>&nbsp;&nbsp;I designed small glider thar cooperate with launcher.It is available here:<a target="_blank" href="https://makerworld.com/en/models/16774#profileId-15557" rel="nofollow noopener">https://makerworld.com/en/models/16774#profileId-15557</a>and works like that:<figure class="image"><img src="https://media.printables.com/media/prints/415098/rich_content/74b00a80-1e55-4d9d-b0a8-ef45f0b99777/swift.gif"></figure>Have fun&nbsp;&nbsp;

工具

玩具