user_2940897098

Techro3D

Earring organizer | Earring rack | Earring holder&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453430/design/2024-05-04_dad7289a2bbdd.jpg">

Earring organizer | Earring rack | Earring holder

presents

AU3D

The existing radius gauges did not fully meet my requirements, prompting me to design these new ones. I sought gauges that could be conveniently attached to a keychain or something similar, eliminating the need to sort them post-use. Additionally, I required the flexibility to swiftly detach a single gauge for use in hard-to-reach corners.<h3>Updates</h3>17.01.2024: I've introduced an 'Imprint' variant to the RAW files and the regular print profile. This new version is designed to be more space-efficient, with all gauges sitting flush against each other. The key feature of this variant is the cut-out number on the top layer, which reveals a contrasting color from the layer beneath.21.01.2024: I just published an extended range of <a target="_blank" href="https://makerworld.com/en/models/150708#profileId-164401" rel="nofollow noopener">radius gauges, ranging from 30 to 100mm</a>.<h3>Printing Instructions</h3>You have the option to enhance the readability of the numbers by performing a manual filament swap (already included in the print profile) during printing, maintain a single color for simplicity, or add color post-printing using a Sharpie marker.Make sure you have great bed adhesion as the sharp corners are vulnerable to warping. Maybe you have to use a smooth pei sheet or spray adhesive. However, I have consistently achieved successful prints of this model on an open-frame P1P printer using the standard textured PEI sheet without encountering any problems.<h3>Measurement Tools Collection</h3>I am constantly developing more measurement tools. Check out my entire <a target="_blank" href="https://makerworld.com/en/u/2942852598/collections/396042" rel="nofollow noopener">Measurement Tools collection here</a>.

Radius Gauge R1-30mm

tools

chiz_m

<h3>The most effective, ergonomic and easy-to-use PTFE release tool for the A1 – the EZ A1 PTFE Release Tool!</h3>*** For best results, please see Tips for Success section ***<h3>If you find that this tools works great for you, pls hit that BOOST button!</h3><h3>PROBLEM</h3>PTFE tubes on the A1 AMS Lite hub is difficult to remove. Per the Bambu wiki, one has to press down the locking ring with a tweezer in order to remove the PTFE tube. I find it too fiddly and I&#39;m afraid that constantly doing so will eventually cause the gantry to sag and affect alignment.<h3>SOLUTION</h3>Design an ergonomic tool that will allow easy release of the tube without pressing the entire hub down using only one hand while allowing the other hand free to pull the PTFE tube.<h3>FEATURES</h3><ul><li>Stable and efficient - less prone to errors as tool attaches to the hub preventing accidental sliding</li><li>Easy to use - Designed with the best user experience in mind! Operate the tool comfortably and naturally by squeezing the thumb and index fingers together</li><li>Less damaging to the printer - during operation of the tool, stress is limited to the filament hub only and not to the entire gantry</li></ul><h3>PRINTING DIRECTIONS</h3><ul><li>Choose between the default profile (better print quality) or the vertically-oriented profile (recommended for smoother operation) which makes the layers on the thumb press perpendicular to the layers of the clamp part which allows for smoother sliding action.</li><li>Use rigid filaments such as regular PLA, PLA+, ASA, ABS, etc. DO NOT USE matte or silk PLA as these filaments are soft and do not provide strong layer adhesion.</li><li>Print as oriented.</li><li>Comes with built-in supports. No need to turn on supports.</li></ul><h3>TIPS FOR SUCCESS</h3><ol><li>If you find the tubes still very hard to pull out, try pressing the tube down slightly to allow the metal locking teeth to release before pulling the tube out.</li><li>Make sure that you have the thumb press aligned in the corner and that it&#39;s pressing only one ring at a time. Otherwise, if it&#39;s hitting other rings, you might not be pressing the ring down enough.</li></ol><h3>HOW TO USE</h3>IMPORTANT: Tool is not meant to be permanently attached to the printhead as it will prevent filament tangle detection to work. Remove the tool after use.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000392785/design/2024-04-27_283930b7afd63.png"></figure><h3> </h3>

EZ A1 PTFE Release/Remover Tool

printer

sinidus

Practical tamping station for Breville/Sage 54mm portafilter!A perfect complement to your beloved Breville Barista Express/Pro/Touch portafilter!Alignment and tamping becomes much easier. Simply attach the portafilter and achieve perfect results effortlessly. Even works with bottomless portafilters!&nbsp;Compatible brands:* All Breville and Sage 54mm portafilters.* Bork c804* Gastroback

Tamper station SAGE/Breville 54 mm portafilter

prints

Hamstah

Update 25/11/2023: I've added stronger versions of all 3 sizes. Some people were having difficulty printing the original model, so I've increased the height and thickened the links to give the model quite a bit more strength. The trade off is that the model is slightly less flexible, but definitely still a lot of fun to play with. Hope that helps!--&nbsp;Dual sided triangle “chain mail” style fabric. Fun to play with! I recommend printing the tester first, as it is really important that the filament adheres well to the bed for a good print. If one triangle gets knocked off the bed, it can ruin the print (though I have had success if one or two get knocked loose).&nbsp;The easier model to print (and more fun in my opinion) is the 120mm square, but I included a 250mm wide strip for those that want more of it.&nbsp;I also highly recommend using a plastic scraper to remove the print from the bed, and you won't be able to get the fabric to release by bending the bed, and pulling on the fabric will snap the joints.&nbsp;Consider changing filament on the middle layer to get a second colour on the flip side of the fabric!&nbsp;Warning: The 250mm wide version of the fabric takes a very long time to slice!

Fabric Fidget

filament left

Tommy

Simpatico porta bottiglie di Birra.stampato in pla: sostiene bene il peso(consiglio di mettere le bottiglie vuote per un lungo periodo di esposizione)il modello si incastra perfettamente ma visto il peso delle bottiglie e meglio usare un p ò di colla!infilare le bottiglie insieme, altrimenti si sbilancia. (non è possibile mettere una sola bottiglia)!Attenzione a quando si tolgono, levarle in contemporanea.non volete mica sprecare la birra ?&nbsp;Diametro 62mm. max. 330mlDiametro 67mm. max. 500ml&nbsp;fatemi sapere nei commenti se vi e piaciuto, oppure se c è qualcosa che non va bene.Una piccola recensione positiva, mi stimola a progettare con entusiasmo.&nbsp;Buon divertimento.

Sexy beer Holder

joke

Lofted Goods