user_2877022775

ManxSteve

Designed to go on the side of an aquarium to allow plants to be grown out of the top of the water.&nbsp;I printed the back section flat and used tree supports to print the area where the threads are.&nbsp;You will need to print 2 of the side panels.

Aquarium Fish Tank Hanging Plant Basket

鱼缸

Roland Deschain

I loved the concept behind <a target="_blank" href="https://www.printables.com/social/11728-lukes-3d/about" rel="nofollow noopener">Luke's 3D's</a> original model but it didn't fit my daughter's toothpaste. I also found the model quite hard to assemble as the tolerances were tight and there was little to no horizontal expansion (elephant's foot) compensation built in.So while I was lengthening the model I decided to make the following improvements:<ul><li>Increased shaft and body length by 10mm</li><li>Increased tube slot width on the shaft and body slightly</li><li>Added chamfer to all surfaces that touch the build plate to compensate for horizontal expansion</li><li>Added a bump on the shaft to prevent the tip from coming out while removing the tube</li><li>Stiffened up the ratchet arms</li><li>Improved aesthetics (subjective :))</li><li>Less post processing is required for assembly</li></ul>Warning: If you print a third party profile you may not be getting the latest version or the highest quality print. &nbsp;If you like this project, please don't forget to ❤ Like and ★ Rate! <h4>Printing tips</h4>I've been printing the bodies in PLA and the handle, ratchet, and shaft in PETG.<ul><li>0.4mm nozzle</li><li>0.2mm layer height</li><li>Support is not required</li><li>Print as shown in the attached screenshot (widest flat faces touching build plate)</li></ul>

Ratcheted Toothpaste Tube Squeezer

居家

dachu02

Crossing X train track for wooden trains, works great with ikea, brio, bigjigs and other wooden train tracks.follow us on Instagram and check what else we've created <a target="_blank" href="https://www.instagram.com/fabrykatorow/" rel="nofollow noopener">https://www.instagram.com/fabrykatorow/</a> :)*selling printed models is not allowed*

Crossing X train track for wooden trains

轨道

AU3D

This is a new adaptation of Apex23&#39;s top mounting shelf, specifically designed for boards mounted with 10mm spacers, such as the <a target="_blank" href="https://makerworld.com/en/models/420877" rel="nofollow noopener">IKEA Skadis Wall Mount by AU3D</a>, <a target="_blank" href="https://makerworld.com/en/models/418874" rel="nofollow noopener">Standoff / Spacers for IKEA Skadis by AU3D</a>, <a target="_blank" href="https://makerworld.com/en/models/419397" rel="nofollow noopener">IKEA Skadis with Standoff (10mm) by AU3D</a>). Each board size (76x56cm, 56x56cm, and 36x56cm) has its corresponding shelf size to ensure a perfect edge-to-edge fit. Variants with a 5cm cutout on the back sides are included to accommodate boards mounted on the first row, preventing interference with the spacers (they still need 1cm of space at the front; add custom negative cubes if you need more clearance). Additionally, an extra profile is provided to fit the limited space on A1 Mini machines.<h3>Skadis Collection</h3>I am constantly developing more IKEA Skadis attachments. Check out my<ul><li><a target="_blank" href="https://makerworld.com/en/u/2942852598/collections/453266" rel="nofollow noopener">IKEA Skadis Shelves, Trays and Container Collection</a></li><li><a target="_blank" href="https://makerworld.com/en/u/2942852598/collections/188108" rel="nofollow noopener">General IKEA Skadis Collection</a></li><li><a target="_blank" href="https://makerworld.com/en/@AU3D/collections/1044616" rel="nofollow noopener">IKEA SKADIS Boards Collection</a></li></ul>

Top Mounting Shelf for IKEA Skadis (10mm Spacer)

宜家

Celestin

You&#39;re tired of seeing your desk cluttered with 3D printing debris or various waste!&nbsp;The solution is here: a trash can that attaches directly to your desk. Simply slide it on, and your waste will now be confined to one place.&nbsp;It&#39;s as simple as that: you print it and screw it onto your desk. It can be adapted to desks up to 3.5 cm thick. I&#39;ve added a piece of TPU to ensure better grip under constraint.&nbsp;I made 2 versions of my trash can, one large which you can see in the photos with a height of 160 mm, and another smaller one with a height of 115 mm, for those with less filament and who want to print faster. (The assembly remains the same.)&nbsp;And there you have it, problem solved! With its large capacity, you won&#39;t need to empty it every day; it can hold a lot for a long time.&nbsp;IMPORTANT NOTE: There may be a slight lack of grip for the trash can to hold well. To remedy this, you can apply a bit of hot glue on the top of the trash can that is in contact with the table.  After several tries, I found that the best solution was to put the trash can under constraint with the TPU. To do this, you screw the trash can normally to the table, then you remove it and tighten it a bit more. This way, when you put the trash can back in place, it will be well secured and will hardly move at all. Good impression!

Desk trash bin

置物

GianfLab

Porsche 911 GT3 RS 992 desk decorationDimensions: 20.5 x 6.5 x 2.5 cm 8.1 x 2.6 x 1 inch (length, height, depth)&nbsp;Print Settings:Use standard setting .20mm Layers + Only one wall on first layerNo Supports

Porsche 911 GT3 RS 992

好玩小物

Hemoner

The use of the Bambulab logo is decorative only, this model is not an official Bambulab model&nbsp;There are 3 versions:<ol><li>Regular one (AMS)</li><li>One color (No-AMS)</li><li>6 Hotend version</li></ol>&nbsp;This is a Bambulab A1 series hotend storage box, I was inspired by <a target="_blank" href="https://makerworld.com/en/u/3854142654" rel="nofollow noopener">Harry Porpise</a> accesory box aesthetics, check his profile!Is meant to be combined by his accesory box, check the model in here:&nbsp;<a target="_blank" href="https://makerworld.com/en/models/113622#profileId-122125" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000134043/design/2023-12-29_150af275d2633.webp"></a>&nbsp;It has capacity for four hotends and one bag full of screws&nbsp;Want to hang it in your wall or hex base? Try this remixes!&nbsp;<a target="_blank" href="https://makerworld.com/en/models/454847#profileId-362348" rel="nofollow noopener">https://makerworld.com/en/models/454847#profileId-362348</a><a target="_blank" href="https://makerworld.com/en/models/404445#profileId-306200" rel="nofollow noopener">https://makerworld.com/en/models/404445#profileId-306200</a>&nbsp;Also check this silicone sock box!&nbsp;<a target="_blank" href="https://makerworld.com/en/models/190345#profileId-210110" rel="nofollow noopener">https://makerworld.com/en/models/190345#profileId-210110</a>&nbsp;UPDATES01/17/2024 - Added a version that supports 6 hotends (Thanks <a target="_blank" href="https://makerworld.com/en/u/327161251" rel="nofollow noopener">@PaBa</a>)01/16/2024 - Added one color variation, for people with no AMS! The white text and graphics are just grooves, so is easy to print01/15/2024 - Added new cover version with looser fit, if you are having problems with the regular cover, print this (It has 0,1mm tolerance)&nbsp;If need variations of the model, ask me for it!

鱼缸

居家

轨道

宜家

置物

好玩小物

配件