user_2742936673

SE3Dtech

I designed this simple rolling monster truck since most of the vehicles I found uploaded already were either decorations (did not roll) or not modeled well (mismatch in sizes between axles/wheels, hard to print, etc). &nbsp;The 3mf file includes 2 separate plates, one with 4 wheels and one with the 2 axles and main body. The main body is designed to be printed on it's side. It's recommended to use a brim and tree supports for the axles. Depending on your printer's tolerances, the filament you use, and whether brims are used or not, the fit of the axles in the wheels may vary. You will likely need to glue the axles into the wheels with super glue or similar.

Monster Truck with Rolling Wheels

Toys

PCHuDSoN

I printed the spool winder by V3 Precision as had a couple spools that were not working well in the AMS.Although it worked and uses no fittings other than the screws to hold it down, it didn't respool as I expected. <ul><li>I had to touch the doner to add resistance to it otherwise it free wheeled too much and filament wouldn't spool nicely.</li><li>I also found that a lot of filament would gather to one side but would couldn't move the spool guide over as then the gears would not mesh. The would cause it to fall to the middle and be lose on the spool. I was only able to get around 800g on the spool before I ran in to issues.</li><li>I also thought the spool guide moved too quickly.</li><li>I also looked in to other remixes available and found it was possible to print stronger parts support free, so now only a few parts need supports.</li></ul>So I have put together a profile brining the remixes together.<ul><li>I was also inspired by the remix that split the worm gear but I split it myself so that I couold add connectors to make it easy to join. This can be assembled without glue and the threads keep together but I added a small amount along the length.</li><li>I added custom wipers inspired by the ones in the Pastamatic winder. I just used some cardboard but you can print and use the TPU winders from the winder.</li><li>I cut the top from the filament guide, this allows it to be printed with its top on the build plate and therefore doesn't need supports.</li><li>I also made the worm gear about as large as it can be for the size of the stand to slow down the guild movement speed. It is also deeper so it can be positioned further forward so the filament doesn't gather all on one side. After my modifications I was able to transfer a brand new 1kg spool with no issues.</li></ul>Another tip, avoid over extrusion as the threads are very tight (I had to do some clean up).&nbsp;It would still be possible to add the manual handle. I was always intending to use with the 3/8" drive so i have not included the handle parts, but you can always get them from the source models.&nbsp;This is a day in printing and the best part of 1kg in filament. Might be better to move the parts around on plates and print parts in end of rolls which is what I did as there are not that many parts that actually require a larger amount of filament.&nbsp;Infill is high and the number of walls is fairly high as most parts need to be tough as will be taking the wear. However even driving mine with a drill I haven't had any issues and it tends to bed itself in.&nbsp;Thanks for downloading.&nbsp;

Filament Spool Winder - V3 Precision Remix Collection - No fittings required

Spool Winder

Ocular Dynamic

Since i&#39;m not using the spool holder attachment on my A1 Mini, I decided to convert it in to a low key/stealth scraper holder mount. I also used the scraper holder section from thrutheframe&#39;s design because it has the added option of inserting magnets to further secure the scraper from any movement.&nbsp;Very simple print, no supports. Just print and slide it in place.Ø6x3 magnets - 2pcs (optional)

A1 Mini Scraper Mount

A1 Mini Stuff

madizmo

EDIT: Added some wider tapered sides to the guide as it could get caught on spools with large openings on the spools, need feedback if anyone still has this issue!&nbsp;This is the newest version of the filament guide for my <a target="_blank" href="https://makerworld.com/en/models/156593#profileId-171555" rel="nofollow noopener">AMS saver</a> that works amazing! This version has a more tapered inlet like the one on the AMS feeder so when it gets to the end of a spool it will be able to pulled the bent end of the filament through. The next best part is this one actually threads on to the bowden tube and bites in very well so no more chance of them falling off on a retraction and getting tangled in the spool. My tests were done in PETG on the P1S using generic PETG profile and fit perfect with the Bambu PTFE tubes. If you find them too tight or too loose either scale them a bit or adjust your flow rate. As they are you do have to put a bit of force to thread them on, let me know how the work for you!&nbsp;The arrow side faces up to the lid on install!

Toys

Spool Winder

A1 Mini Stuff

Random Stuff to Print