Tk11883

Raditive Prints

Print Profile 1 has no sign on top just a capPrint Profile 2 has a Sign you can customize in bambu studio&nbsp;If you are looking for more options as well as some different hangers for keychains and earrings please see the keychain rack on my website<a target="_blank" href="https://www.raditiveprints.com/products/modular-spinning-keychain-display" rel="nofollow noopener">https://www.raditiveprints.com/products/modular-spinning-keychain-display</a>&nbsp;This rack is designed to hold Dragons. I have tested it with Cinderwing3d Crystal, Rose and Gemstone Dragons. It holds them if they are scaled between 65% and 100%. I use this at my craft events to clear up some table space for the large dragons.&nbsp;Each piece screws together.&nbsp;There are a few different length shafts for depending on what length dragons you plan on using.Slide the necks of the dragons in the slots to hang them&nbsp;The top part is the tallest piece. This has a smooth area on it that is designed for the rack to fit on.&nbsp;DO NOT OVER TIGHTEN OR THREADS HAVE A CHANCE TO BREAK.&nbsp;You may want to do some test prints with the threads to make sure printer is dialed in.

Dragon Display Rack or Keychain Display

display 

jeffrudzinski.prestige

This is a full chess set with each piece being a different character or reference to the series. The intended character-peice combination is as shown in the photos (ex. Link and Zelda are King and Queen for the “white pieces”, Ganon is the King for the “black peices”. Pieces have been sized to conform to standard chess piece sizes. The set includes several additional “alternate pieces” that can be used in place of the “standard” set. However, it should be noted that the alternate pieces were difficult to print. Every model in the main set should print. Recommended Print Settings: Nozzle: 0.40mm Layer Height: .20mm or lower Supports: Regular supports with Snug fit. Tree supports also work, but have been less reliable. Use build plate only for tree supports. Support Threshold Angle: I printed using 20. There is a delicate balance between support threshold and print quality. These models have a lot of things that need support that are also think and delicate. Bows, arrows, fingers, etc. If you set the threshold angle too low, the print will get messed up. If you set it too high (35+) there will be so many supports that removing them from the many small delicate sections of models will be difficult to do without breaking the model. Filament: I have only tested these models with PLA and Silk PLA. They print significantly easier with regular PLA (I used Inland). Silk PLA makes these things look awesome, but it is more brittle, and again, lots of small delicate parts. Ironing: Several models benefit from top surface ironing. Deku Tree for example. Most do not need them. Infill %: I recommend at least 50%. It gives the pieces a good feel and not as likely to tip over but also saves on filament. Infill pattern: whatever you want, I think I used cubic for the most part. Walls: 3. You can do 2 if you want, but the extra wall makes them sturdier, especially for ones with thin legs. Print Speed: 100% or lower. Storage: This set is not recommended as an every day chess set. It's for display and/or special occasions. If you have children in your home, you should keep these packed up. You can find “pluck and pull” foam padding online for relatively cheap. 2" is what I used. Check the photos to see what I mean. General Printing: It may be a task, but I would suggest printing one piece at a time, especially for the larger more complicated ones. Print Times: The larger pieces take ~2 hours to print. The pawn row takes ~1 hour per piece.

Legend of Zelda Chess Set (Full models)

chess

Type1Printing

A cool little articulated dragon!

Articulated Flexi Dragon

dragons

phyXoo

80% scale model0.2mm layer height0,3mm Top Z distanceSmoothened Top surfaces&nbsp;Supports are really easy to remove.

Pikachu - Pokemon

Tyler's Collection

design3d

Corner holder for BambuLab printers, so they don't move during printing and sit still in place :)

Corner holder for BambuLab P1P/P1S/X1C

upgrades 

DjangoCashflow

Bring the power of the galaxy to your home with this Death Star Floating Planter, a remix of the original model by <a target="_blank" href="https://www.thingiverse.com/thing:3432933" rel="nofollow noopener">tato_713</a>. This stellar planter is not only a nod to the epic space saga but also a unique way to showcase your love for botany and sci-fi in one go.  Features:<ul><li>Galactic Design: Expertly crafted to resemble the formidable Death Star, this planter adds a touch of intergalactic intrigue to your decor.</li><li>Floating Illusion: Mounted on a sleek pedestal, the planter creates a floating effect that defies gravity and captures the essence of its celestial inspiration.</li><li>Functional Art: More than a mere model, it serves as a fully functional planter, perfect for housing a variety of small plants or succulents.</li></ul>Installation is as simple as it is impressive: place your plant in the spherical planter, mount it on the pedestal, and watch your space transform with the power of the Force. Suitable for Jedi, Sith, and neutral beings alike, this Death Star Floating Planter is destined to become the centerpiece of any room it occupies. Resize both Death Star and stand at the same time to match your pot size!

Death Star Floating Planter

vase

PrintPractical

Give your family member or friend a fun puzzle filled with cash. Sometimes you feel bad about giving someone cash for the holidays, but this puzzle adds a little bit of fun and makes them work for it! The Maze part of the print can be printed with no supports. I recommend printing the lid upside down with normal supports for the nubs. It has been very easy to break them supports out. There are 3 mazes included (Easy, Hard, HardPlus). The HardPlus maze just includes a few fake paths to make it a tiny more difficult. The fake paths are very short.&nbsp;Check out the video to see it in action: https://youtu.be/UJ3_uOS36g8

Cash Gift Maze

Christmas 

SavageLau

<h3>If you want a commercial license, check out my bio and get it from Patreon.</h3>Permission only given for personal use.&nbsp;This model is design for MakerWorld light contest (1/5). Complete free version is only available on here Makerworld. &nbsp;Hey guys, I am here to introduce you the ultimate Light sword. This design is combined with retractable and light elements. All the parts is printed beside the Light source (Cat Light). I will put information of this Cat light so you can buy it via amazon, I don't have any affiliate link or anything, so I will provide information you will need to do you own research and buy the Cat light.&nbsp;When it works with different light & filaments.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_fc6e7544caab1.gif"></figure>&nbsp;This design idea come from Cat light, I was playing with my cats with this cat light that my boss bought a while ago. I relize that this Cat light come with strong while light, violet light, and red light. So I came up a idea to fully utilize these light to make a Light sword. Design was focused on adopt and integrate this CAT light into the system.I want it to hide inside of the sword, but you could still switch the light, to turn it on and off. I also want it to be able to retractable, so it will be fun to play. So, eventually I came up with this design.&nbsp;&nbsp;This Sword takes around 4h20m to print on X1C, takes around 140g of filaments.&nbsp;&nbsp;<h3>Upadate: 1.8.1 (2/1/2021) </h3>Improving tolerancing on light switch mechanism, improving lower external shell & cap tolerancing. Cap piece now might need force fit.  &nbsp;<h2>Switching light: (on/off)</h2>Still have a little bit tolerancing issue, will update later.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_0fba44beb880b.gif"></figure>&nbsp;<h2>Required CAT Light:</h2>If the picture looks like this, it should work. It just rebranding on different store.&nbsp;<figure class="image image_resized" style="width:70.19%;"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_aed96d05f56f4.png"></figure><figure class="image image_resized" style="width:57.22%;"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_b63310365086e.png"></figure><h2>You may like: </h2>Light Saber Lite: If you don't want to go for this complicate design, you may like this simple one.<a target="_blank" href="https://makerworld.com/en/models/163782#profileId-179797" rel="nofollow noopener">https://makerworld.com/en/models/163782#profileId-179797</a> &nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-30_dd836c79602fc.jpg"></figure><h2>Material Suggestions:</h2>I Highly suggest to use Glow in the dark filament or Translucent filament with some light color.As the CAT light within the sword, it will constant charging the glow in the dark filaments, if you have rainbow glow in the dark filaments, it will get a lot of amazing color.&nbsp;For external parts, DO NOT USE SOME BRITTLE silk filaments, it will break very easily. Some silk filaments will have very poor layer adhesion due to high speed printing cause part failure.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_081a4cd97007d.png"></figure>&nbsp;<h3>Filaments that I use for internal parts:</h3>Glow in green: Inland Grow in the dark ABS. Muti-color one: Gradient Multicolor Grow in the dark PLA.&nbsp;<h2>Post Work:</h2>You will need to remove the brim on the internal parts, it should be very easy to remove. Brim on external parts should be easy to remove and clean too.<figure class="image image_resized" style="width:55.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_80fba4ac102d1.gif"></figure><h2>Installation:</h2>Refer this clip.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_e9bd991544144.gif"></figure><h2>Printing profile:</h2>This design have small contact area on the build plate, make sure you clean your build plate and enable bed leveling before printing. There is no support needed.I put 3 different printing profile up there, please refer pics and pick what you like.&nbsp;<h2>Design:</h2>The retractable mechanism part is very simple.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_7f087d9731033.png"></figure>How to adopt CAT light and keeps it's function(switch lights & on and off) takes a little bit brain power.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_38f187437649b.png"></figure>The tolerancing part torturous and time-consuming. Since I don't know what filaments you are going to use, since filaments sinkage rate have big different from type to type / brand to brand. Since I decided post this design, I want to get it to able to work for most people. So find a balance between different material is very challenging. I have tested PLA, silk PLA, PETG, ABS, so all tolerance should work okay in most cases.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/556982/2024-01-29_e1ba66681e517.png"></figure>Have fun!

Ultimate Light Sword (Retractable) v1.8.1

sabers 

Uzivatel004

assassin's creed keychain