user_2573591792

01makes

Bag hanger for closet with hanging rod&nbsp;<h2>About</h2>I wanted to hang my backpacks from the hanging rod in a spare closet, and designed this hanger/hook. It has a rotating mid-joint, primarily to enable printing in the strongest orientation.&nbsp;<h2>Printing</h2><ul><li>Print-in-place rotating joint. Please use 0.4mm nozzle.</li><li>No supports needed.</li><li>Use strong filament, ie, do not use softer filaments like silk.</li><li>Use filament with less shrinkage rate. This helps with the printing of the rotating mid-joint.</li></ul>&nbsp;<h2>Assembly/Use</h2><ul><li>After printing the hanger, allow it to cool, then work the rotating joint loose.</li><li>Rotate the two halves and align the two notches to orientate the hanger correctly.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000463544/design/2024-05-14_cceaf55aac2808.jpeg"></figure>&nbsp;&nbsp;&nbsp;<h4>Please check out my <a target="_blank" href="https://makerworld.com/en/@01makes" rel="nofollow noopener">other models</a>, TYSM! I test and refine my models extensively before sharing.</h4>&nbsp;___

Closet bag hanger wardrobe backpack hook

Flame

***Large version available here here:&nbsp;<a target="_blank" href="https://makerworld.com/en/models/453648" rel="nofollow noopener">https://makerworld.com/en/models/453648</a>&nbsp;Strawberry season is upon us and my experience is that the fruits don&#39;t like to be on the ground in dirt and mud because it is prone to rot. Why it did not evolve to be a bush instead is beyond me, but hey this is a good opportunity for some problem solving with 3D printing. I am using store bought strawberry supports and since I have a printer, I was also downloading and testing some designs, but I haven&#39;t found any that worked for me perfectly, so I set out to create one from scratch to incorporate what I have learned by using these.&nbsp;Features:- Support size: 23 cm (~9 inch) diameter - Leg size: 10 cm (4 inch) - you can push it to the ground to set your height preference- The round support is cut in half to allow for easier insertion close to the plant. - Each half has 3 legs, so it will not topple over - Legs are printed laying down, instead of standing up so it will be much stronger this way - Each leg is pointy, so it will allow for easier insertion to the soil (our soil contains a lot of clay) - Each leg has a strong turnable locking mechanism to keep it in place, no glue required. This was one of the things that pointed me to design my own one, since none of the designs I found had it and legs were always a pain. If you glue them in, it will take up too much space for storage while it is sitting in the shed waiting for the next season.&nbsp;Word of caution/ additional tips and tricks:- ASA recommended since these will be bombarded with UV rays from the sun, so if you want them to serve for a lot of seasons, it is better to use ASA. Depending on your brand of filament, PLA might give you a few seasons as well since these tend to be outside only for a month or two every season. - The legs print fine with 0.2mm layer height, but then they will give you a textbook stairstepping on the surface. You can decrease the layer height as you see fit, but in reality it does not impact the functionality in any way. - Inserting the legs maybe a bit tricky depending on your filament and how tuned your printer is. If it is too hard when trying to insert these perpendicular to the base, then try inserting just one corner first in a 45 degree angle and then move it to 90 degree while one corner is in there, it tends to be much easier this way. - There is an overhang area where the leg locking mechanism is located. Again depending on a number of factors, you printer might string here a little bit, but a Bambu should be more than capable to produce this overhang without any supports. The legs tend to be strong enough to remove the excess strings here when locking in place for the first time, but if you feel that it does not want to turn, you might need to do a bit of cleanup with a box cutter. - Turn the legs half a turn (180 degrees) in any direction to lock them in place. Removal is done the same way.

Strawberry support with lockable legs - 23cm

Planties

Applejax_Industries

(Please know the printer profile uploaded is only one of seven total print plates. The other plates are located in the RAW files section)&nbsp;Christmas has always been a time of joy and togetherness so we wanted to create something that can be used year after year to bring those smiles of anticipation in the eyes of children waiting for that special day when Santa comes. That is why we choose to create this advent calendar and also to share in process of putting it together with your family and or friends.&nbsp;The stocking is quite large for 3D printed objects measuring in at almost 18in tall and 11in wide. Being this size it is of course not a quick print in anyway and does require the use of an AMS, but we wanted to ensure the drawers had enough room so you could add some special treats, messages, jewelry, and more. We also created an assembly guide and link to the light we used to make this easy for you and your family to put together.&nbsp;Print Settings&nbsp;All filament colors used are basic Bambu PLA with the exception of the Dark Green which is Hatchbox!There are a total of 8 print plates with saved settings!Layer Height on all but the drawer handles is 0.20 StandardLayer height on drawer handles is set to 0.12 fine and change the print speed to slow or silent.&nbsp;We hope you enjoy and Merry Christmas to all!

Christmas Stocking Advent Calendar

holidays

hdticket2

Pyramids elevate your workpiece above the surface, making cleanup easier. Non-stick points prevent paint from smudging, allowing you to flip and paint the other side without any delay.

amy

Planties

holidays

Maybe?