user_2485454489

Fresh Brewed Design

Your cat(s) deserve the freshest canned meat product and nobody wants old cat food lurking in the back of their cabinets. This dispenser serves up your cans in first-in, first-out order. The dispenser prints without supports and no hardware or glue is required for assembly.&nbsp;Design<ul><li>Holds 8 3oz cans per dispenser (note: tested with Fancy Feast cans which have about a 66mm diameter and a 37mm height - you may want to check your cans before printing if you prefer a different brand)</li><li>Cans roll smoothly from top to bottom for easy loading</li><li>Fits in a 12in deep cabinet</li><li>Slim profile makes it easy to fit multiple dispensers side-by-side</li><li>Printable on a 180x180mm print bed (e.g., Bambu A1 Mini, Prusa Mini)</li></ul>Dimensions (LxWxH) 280.5x47.6x172.8mm&nbsp;Print settings Nothing special. I test printed with PLA and slicer defaults. STLs are oriented as recommended for printing.&nbsp;Assembly Assemble by sliding the corresponding dovetails together. When assembled correctly, your pieces should all sit flush on both the interior and exterior surfaces. The dovetails should be a fairly tight fit.<ol><li>Print all four components (left front, left back, right front, right back)</li><li>Attach left front to left back and right front to right back by sliding the dovetails together. Ensure all 3 dovetails are engaged on each side. You may find it easiest to partially engage the larger dovetail at the bottom before aligning the middle and top dovetails.</li><li>Attach the left half to the right half by sliding each set of dovetails in from the bottom. You may again find it easiest to start from the bottom. Just make sure top, middle, and bottom dovetails are secure front to back.</li></ol>Notes<ul><li>If you have a larger printer, I&#39;d love your help in testing out additional sizes. I may also do a 12 can version in 6 parts if there&#39;s interest!</li><li>If you plan to remix this, be aware that most cans aren&#39;t simple cylinders. In real life, the cans sit at a slight angle due to the lip around the top. This increases their total width by enough to make a difference. The design accommodates this to avoid an otherwise dispenser-jamming amount of friction between the cans and the side wall.</li></ul>Inspiration/credits<ul><li><a target="_blank" href="https://www.thingiverse.com/thing:4428664" rel="nofollow noopener">Aeris - Cat Food Can Dispenser (modular) by Erdrick</a></li><li><a target="_blank" href="https://thenounproject.com/icon/cat-6048434/" rel="nofollow noopener">Cat icon by Kim Sun Young on The Noun Project</a></li></ul>

Cat Food Can Dispenser

宠物

Denste17

Now also see the new minimalistic evolution of this door holder: <a target="_blank" href="https://makerworld.com/en/models/141267#profileId-153949" rel="nofollow noopener">Minimalistic Bambu door holder by Denste17</a>&nbsp;&nbsp;Update 30-10-2023:&nbsp;Due to the demand of this model, I decided to create a two color variant with the Bambu Lab font on it.With AMS everything looks cooler and you can also see directly in which direction the holder should be put.&nbsp;&nbsp;Original Release 30-07-2023:&nbsp;I designed this simple and fast to print bracket to hold the door of the Bambu Lab X1 and P1S open.While printing PLA with textured or high temperature plates, it is possible to get nozzle clogs because of the rising chamber temperature. One solution for this is to print top glass risers with integrated vents or just to leave the door open. While leaving the door open it really bothered me to see the door vibrating.So my solution is this little bracket, which fixes the door 10cm open. The door cannot vibrate due to the printers vibrations anymore.Please pay attention to not damage your door gasket on printer side!First put the bracket on printer side and afterwards bend it slightly away from the door, so the door itself can snap into the bracket. Installation is shown on title picture.Model is mirrored, so you have your textured layer/first layer on the upper/visible side.Bye! Dennis

Simple Bambu Lab X1 X1C P1S Door Holder

Matthew Ghost

<ul><li>Secure Valuables Storage: Safe is perfect for safeguarding your money and precious items.</li><li>No Additional Parts Required: No complicated setup! This safe doesn't need any bearings, screws, glue or additional purchased parts.</li><li>Functional Mechanical Lock: Security is key – our safe features a functional mechanical lock for an extra layer of protection.</li><li>Dimensions 140x130x140 mm: Spacious enough for your valuables, yet compact enough to fit anywhere.</li><li>Include coin slot</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/396562/2024-01-12_a4eacf6d63b6c.gif"></figure>Assembly instruction:Instructions can be found in the video below. Please follow the procedure: (<a target="_blank" href="https://www.youtube.com/shorts/WcrcSSKChjk" rel="nofollow noopener">https://www.youtube.com/shorts/WcrcSSKChjk</a>)<figure class="media"><div data-oembed-url="https://www.youtube.com/shorts/WcrcSSKChjk"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=WcrcSSKChjk"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/WcrcSSKChjk" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>A VERSION WITH CLEARANCE<ul><li>It may happen that main version will not be assembled due to small clearances. Actual clearance depends on many factors (flow, filament, printer condition)</li><li>Parts with the letter C in their name are parts that have increased clearance. These parts must be glued.</li></ul>

Safe | Vault |  Bank | Money Bank | Piggy Bank | Safe box

工具

Mechengg

This is inspired by the “Annoying Gift Box” that most people (including my wife) have seen on TikTok.&nbsp;The size of the original is quite small, and the 3 different versions of it didn't give me exactly what I was looking for. I wanted a large internal volume (4"x4"x4"), and I wanted this to look like a Christmas present with zero visible screws. So obviously I spent far too much time modeling this up and figured that I would share it for free instead of charge people for it :)&nbsp;3 BoxesRibbon & Bow120 total screws&nbsp;You do need a few dabs of CA glue to hold the inner box posts in place. :) You can add glue for the white threaded part as well but it works without it&nbsp;Thanks for viewing, and take a look at my other models for things that I have designed for myself because the originals weren't exactly what I was desiring&nbsp;EDIT: I have also designed a bin with magnetic slide lid for storing the multitude of screws. 3 partitions to separate by color :)<a target="_blank" href="https://makerworld.com/en/models/82815#profileId-88321" rel="nofollow noopener">https://makerworld.com/en/models/82815#profileId-88321</a>

宠物

3d

工具

礼物