Schorsch-Moe

TBone_427120

This lampshade is designed for the <a target="_blank" href="https://makerworld.com/sv/models/13717#profileId-13429" rel="nofollow noopener">Bambu Led Lamp 001</a> kit ←- Follow this link to get the model for the base that holds the electronics and that this globe shade locks into.&nbsp;This is a moon lithophane model for the LED Lamp kit base built using NASA SVS data.&nbsp;Before printing, it is highly recommended to test and calibrate the filaments. Test Prints are provided in a profile to test the trickier parts of the print, in particular the top of the moon. Printing the sliced off moon top will give an idea if the flow rates need to be calibrated or if the layer heights need refining.Both of these are eSun PLA, and both were printed using the same eSun PLA+ profile. <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_e7cbdab0e3545.jpg"> The one on the left (&#34;creamy&#34;) needed different flow rate settings to avoid the gaps in the thin walls. Moral of the story: spend the extra 20 minutes to at least run the Auto Calibration for a new filament (and Manual isn&#39;t so bad to do either particularly if you print on the textured plate).&nbsp;The extra big brim is out of an abundance of caution. There is nothing worse than being ten minutes from the end of a 17 hour print and hearing *CRACK* followed by a spaghetti detected notification. If the test print indicates your filament needs a small center support for the top of the moon, “Normal/Snug” supports will work best. Use Manual supports (Auto will result in a ton of exterior supports for the base of the moon) and paint a small dot in the underside of the top of the Moon. The latest version of the model has been made a little thicker and is more forgiving for printing with most filaments. The part that interfaces with the lamp kit base can easily be made a different filament to match the LED holder material or just for variety. Just set the base filament for the “ModifyBaseSettings” modifier. Doing will require only one filament purge, no prime tower is necessary.<figure class="image image_resized" style="width:41.3%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_33ea3c815b5ef8.png"></figure>&nbsp;If using the modifier to make a material change at the base, make sure to pick two filaments that have good adhesion to each other.Because the print requires supports in the base and cleanly removing those supports is important for a snug fit to the lamp kit base, a test print is provided to make sure the filament and support settings will release cleanly. Normal snug supports provided the best results (tree supports required much more effort).&nbsp;<figure class="image image_resized" style="width:17.23%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_f00e2d2199c81.jpg"></figure>&nbsp;If you do use the center support, when removing don&#39;t pull at individual folds from the bottom. Use something to grab on multiple folds as far up as possible (a pair of kitchen tongs works well) and twist.<figure class="image image_resized" style="width:17.52%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_c2509972a68348.jpg"></figure>Twisting will put less stress on the top of the sphere and less risk of pulling away the moon surface. If you have wisps of filaments, resist the urge to use a heat gun because the variable thickness of the shell will contract non-uniformly under the heat. This is the result using a heat gun on a lithophane:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_a27a97fbc55ec.jpg">&nbsp;

Moon Globe for LED Lamp 001

Desing& Art

Marc Elbichon

Simple tea storage box with a window in the front to put a bag of tea as ‘label’, with lid.&nbsp;Stackable, easy to print&nbsp;Enjoy!

Tea Storage Box Organizer

Tools& Aufbewahrung

h3li0

<h2>polygon planter</h2><h3>with wrap-around plate</h3>modern minimalist planter design with polygon pattern that sits elevated in a wrap-around plate&nbsp;update · just posted a companion model, <a target="_blank" href="https://makerworld.com/en/models/500642#profileId-415642" rel="nofollow noopener">zig zag planter · wrap around plate</a>&nbsp;dimensions in mm &gt; x:110 · y:110 · z:100&nbsp;photos show two different color scheme choices, printed in matte black pla, marble white pla, and marble brick pla<ul><li>0.20mm layer height</li><li>10% cross hatch infill</li></ul><h3>notes</h3><ul><li>includes bambu studio 3mf file and STLs</li><li>all photos uploaded are of the actual printed model, taken inside a light-box or in home studio</li><li>if you enjoy this model please consider to <a target="_blank" href="https://www.buymeacoffee.com/h3li0" rel="nofollow noopener">buy me a coffee</a></li><li>commercial licence membership available on my <a target="_blank" href="https://patreon.com/h3li0" rel="nofollow noopener">patreon</a></li></ul>&nbsp;&nbsp;

polygon planter · wrap around plate

Geschenke

Encrust3d

This is an extended version of my slim A1 poop bucket. This has the same width and height but the length on this is 60mm longer than my original Slim A1 poop bucket. This was designed by myself in Fusion 360. This model is compatible with the top mount AMS lite hardware. If you would like a smaller version of this, you can download it here: <a target="_blank" href="https://makerworld.com/en/models/104677#profileId-111711" rel="nofollow noopener">https://makerworld.com/en/models/104677#profileId-111711</a>&nbsp;1/14/24: uploaded no logo version&nbsp;

Desing& Art

Tools& Aufbewahrung

Geschenke

Bambu A1