user_2185247215

MplusM

UPDATE:This model has been replaced by version v2 Plus. Download: <a target="_blank" href="https://makerworld.com/en/models/419236" rel="nofollow noopener">https://makerworld.com/en/models/419236</a>&nbsp;After so many people asked me for my Marble Run 003 expansions and I was not allowed to pass them on, I designed this Paddle Wheel Addon. Based on my improved “jump catcher”, there is now a track extension with a paddle-wheel as an Addon, which btw - from my point of view - shouldn&#39;t violate the license terms of the original Marble Run 003 model <a target="_blank" href="https://makerworld.com/en/models/14265" rel="nofollow noopener">https://makerworld.com/en/models/14265</a> .&nbsp;This track is clearly a shortcut and the marbles that take this route overtake all the other marbles. That&#39;s why I&#39;ve drawn it so that not many marbles go that way. Also, the lower part of the track is slightly uphill and then has only a slight slope in order to reduce the rolling speed. On the other hand this can cause the marbles to get stuck, depending on the print quality or the uneven surface. If this is the case, you just have to warm up the lane (serpentine) with a hairdryer and bend the curve down a little.I would be grateful if you share with me your suggestions and experiences.&nbsp;Notes:<ul><li>This addon contains small parts. Please make sure that children cannot swallow them.</li></ul>&nbsp;Print Instruction and Assembly:<ul><li>Please refer to the instructions in the attached pdf.</li></ul>&nbsp;More control:Do you prefer more control over marbles that take the shortcut? Check out the “Jump Catcher v1B” with adjustable opening (“sliding door“): <a target="_blank" href="https://makerworld.com/en/models/386909" rel="nofollow noopener">https://makerworld.com/en/models/386909</a>&nbsp;Interested in more Marble Run items? Check out <a target="_blank" href="https://makerworld.com/en/@mplusm" rel="nofollow noopener">https://makerworld.com/en/@mplusm</a>&nbsp;&nbsp;

Marble Run 003 Paddle Wheel Addon v1

玩具

skywolf

Redesign @ 2024-04-04 Beautifully symmetrical hook Stored at an angle for easy access Smaller size&nbsp;重新设计 对称美观的挂钩 斜角存放，方便拿取 更小体积

IKEA Skadis Bambu Lab Scraper holder 拓竹铲刀底座宜家洞洞板支架

洞洞板

SPStudio

Extruder AMS Filament Pull Back Fix

拓竹改造

cm3dshop.de

Poop Chute for Paving stone / Cobblestone / Flagstone users with Tray and hidden Handle&nbsp;Easy acess to the Poop with a pull out tray (if you got low space behind and besides the printer)&nbsp;stays in place with 3 round Magnets (attached to the printer) d=6mm ; thickness 4mm (3mm will also work when not pushed all the way in)&nbsp;tray can be hold closed with 4 magnets (Attention at the polarity!) …just optional&nbsp;hidden handle with Bambu Logo for pull out the tray : flat with front when closed ; for opening push the top part in and then pull at the lower part…very simple and easy…fully printed&nbsp;optional Lid for "clean design"&nbsp;&nbsp;This Version is only for Users who using a Paving stone/cobblestone / flagstone 400x400x40mm and 5-10mm rubber mat.It gives additional Space for the Poop…but of course it takes a bit longer to print. ;)&nbsp;Find the Original design (without using a flagstone here: <a target="_blank" href="https://makerworld.com/en/models/76241#profileId-80830" rel="nofollow noopener">https://makerworld.com/en/models/76241#profileId-80830</a>&nbsp;Improvements to the Original Post:&nbsp;-more Space for Poop&nbsp;- deleted the 2 magnets on the side because the printer isn't magnetic there (of course ;) )&nbsp;- give Space for the flagstone and rubber mat at the sliding area&nbsp;- made the back of the slide a bit higher (where the poop arrives) to get a bigger range for the heigth of the rubber mat → rubber mat + Stone = 45-65mm&nbsp;ATTENTION: the print profile uses the PETG/PLA trick so get a super smooth interface between the Tray and the supports!&nbsp;&nbsp;At All it is still a bit over engineered … but…does it really matter?! ;)&nbsp;Just let me know in comments when you have suggestions for improvement.&nbsp;&nbsp;

Poop Chute Tray for Flagstone with hidden handle+Lid

拓竹马桶

理光GR3热靴盖 Ricoh GR3 hot shoe cover