user_2104165403

justinpig

<h2>Deadpool style katana</h2>This is a Deadpool-style samurai sword. Basically, it is designed to be completely disassembly to prevent damage. Some parts can be printed and replaced.&nbsp;The print file is divided into one tray for all single colors, one tray for individual parts, and three multi-color guard settings.&nbsp;2024/03/29 Update: add Assembly steps Gif (page end)2024/04/20 Update:add Face on Guard 3mf&nbsp;Notice 1. When printing wrap parts, use a high-volume fan setting to effectively avoid overhanging quality. 2. The blade part can be printed using petg wire (sturdier than pla)3.All parts have been tested using x1c &amp; a1 mini printing4.When using the a1 series brim, it is recommended to turn it on to prevent the heating bed from being thrown out when moving at high speed and printing failure.&nbsp;Assembly instructions:<figure class="table"><table><tbody><tr><td>1. Handle and strap, confirm the strap installation direction (such as the arrow corresponding)</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-22_89084cef6be2e.jpg"></figure>&nbsp;&nbsp;</td></tr><tr><td>2. Install the handle from top to bottom (as indicated by the arrow)</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-22_e1699b6a7bf16.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-22_a9f51bf44375c.jpg"></figure>&nbsp;</td></tr><tr><td>3. Install hand guards</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-22_c45939bab9112.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-22_3b7bea8077804.jpg"></figure></td></tr><tr><td>4. Combine the handle, strap and hand guard (pay attention to the forward and reverse directions of the blade hole)&nbsp;※Make sure that the holes on the handlebar and the hole on the hand guard are in the same direction and are installed tightly.</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-22_af3f3f3b64c5b.jpg"></figure></td></tr><tr><td>5. Put in the blade (pay attention to the forward and reverse directions of the blade)</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-22_fee63e63c1538.jpg"></figure></td></tr><tr><td>6. Use pins to fix the back cover after installation. Considering the printing tolerance of each printer, 0.1, 0.15, and 0.2 pin parts are provided here, which can be used according to the tightness of the pin.</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-22_e19570b4ed9b7.jpg"></figure></td></tr><tr><td>7. Assembly completed</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-22_b3c4b812fda16.jpg"></figure></td></tr></tbody></table></figure>&nbsp;<h3>Assembly steps:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000387927/design/2024-03-29_ebae28d34495e.gif"></figure>Have fun~~

Collapsing Deadpool Katana (Parts Removable)

鬼滅

misenique

<h2>To hold my razor and brush I created The Razorganizer.</h2>No AMS needed. Just print both plates in different colors and pop the decorative elements in. If the fit is too loose, just add a drop superglue. After printing the hole has a diameter of about 16.8mm. Make sure your handle fits. Since a few people wanted to have a dish under it, I created The “SoapDock”. Its actually sized to fit the Razorganizer. (Click the Photo)<figure class="image"><a href="https://makerworld.com/en/models/390447#profileId-291408" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/763513/2024-03-23_d1cfe13d5109c8.jpg"></a></figure><figure class="image"><a href="https://makerworld.com/en/models/390447#profileId-291408" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/763513/2024-03-23_a8f56dc7a16fd.jpg"></a></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/763513/2024-03-18_8fa3074520d46.jpg"></figure>   &nbsp;Also check out my new Organic Leaf pattern Lamp<figure class="image"><a href="https://makerworld.com/en/models/394045" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/763513/2024-03-25_108eb7353d72b.jpg"></a></figure>

鬼滅

123