CindyChang

zach13

<h2>DOUBLE CHECK WHICH VERSION YOU NEED BY CHECKING THE VERSIONS BELOW.</h2><h2>Description:</h2><p>This is a stackable can dispenser. The purpose of this was to fit as many cans of different types as possible in my standard depth fridge which for my use case was the 12oz 7 can version. See the versions section at the bottom for what cans and what capacities are supported. Leave a comment if you'd like me to add a different can size, ideally with measurements.</p><p>&nbsp;</p><h2><strong>Printing:</strong></h2><p>I printed with Bambu PETG Basic but whatever you have should be fine. <strong>The pegs that hold it together are fairly tight, scale them down if you need to, especially if you're using a brittle filament</strong>. You may also want to use brim on the pegs if you're not using something with good bed adhesion.</p><h2>Assembly:</h2><p>The parts are assembled with 20 pegs. You will need an additional 8 pegs per level you wish to stack. Super gluing the joints during assembly is recommended, though not completely necessary depending on your imperfection tolerance. </p><p>&nbsp;</p><h2>Versions:</h2><p><strong>12oz (355ml):</strong></p><p><a target="_blank" href="https://www.crowncork.com/beverage-packaging/products/beverage-cans/12oz-355ml-standard" rel="nofollow noopener">Info</a></p><figure class="table"><table><thead><tr><th>Cans</th><th>Assembled Dimensions (WxHxL)</th><th>Notes</th></tr></thead><tbody><tr><th>8</th><td>134mm x 91mm x 545mm</td><td>278mm+ bed required, likely won't fit in most fridges. No print profile.</td></tr><tr><th>7</th><td>134mm x 91mm x 479mm</td><td>Should fit most American standard depth fridges</td></tr><tr><th>6</th><td>134mm x 91mm x 479mm</td><td> </td></tr><tr><th>5</th><td>134mm x 91mm x 347mm</td><td> </td></tr></tbody></table></figure><p>&nbsp;</p><p><strong>16oz (473ml):</strong></p><p><a target="_blank" href="https://www.crowncork.com/beverage-packaging/products/beverage-cans/16oz-473ml-standard" rel="nofollow noopener">Info</a></p><figure class="table"><table><thead><tr><th>Cans</th><th>Assembled Dimensions (WxHxL)</th><th>Notes</th></tr></thead><tbody><tr><th>7</th><td>171mm x 91mm x 479mm</td><td>Should fit most American standard depth fridges</td></tr><tr><th>6</th><td>171mm x 91mm x 413mm</td><td> </td></tr><tr><th>5</th><td>171mm x 91mm x 347mm</td><td> </td></tr></tbody></table></figure><p><strong>16.9oz (500ml):</strong></p><p><a target="_blank" href="https://www.crowncork.com/beverage-packaging/products/beverage-cans/169oz-500ml-standard" rel="nofollow noopener">Info</a></p><figure class="table"><table><thead><tr><th>Cans</th><th>Assembled Dimensions (WxHxL)</th><th>Notes</th></tr></thead><tbody><tr><th>7</th><td>181mm x 91mm x 479mm</td><td>Should fit most American standard depth fridges</td></tr><tr><th>6</th><td>181mm x 91mm x 413mm</td><td> </td></tr><tr><th>5</th><td>181mm x 91mm x 347mm</td><td> </td></tr></tbody></table></figure><p>&nbsp;</p><p><strong>7.5oz (222ml): </strong></p><p><a target="_blank" href="https://www.crowncork.com/beverage-packaging/products/beverage-cans/75oz-222ml-crownsleek" rel="nofollow noopener">Info</a></p><figure class="table"><table><thead><tr><th>Cans</th><th>Assembled Dimensions (WxHxL)</th><th>Notes</th></tr></thead><tbody><tr><th>8</th><td>118mm x 83mm x 481mm</td><td>Should fit most American standard depth fridges</td></tr><tr><th>7</th><td>118mm x 83mm x 424mm</td><td> </td></tr><tr><th>6</th><td>118mm x 83mm x 366mm</td><td> </td></tr></tbody></table></figure>

Stackable Can Dispenser

收纳小物

XentoBi

<h3><strong>Model Description</strong></h3><p>“v2” version has no label area in case you want to save even more filament. Otherwise, print the “v3” versions.</p><p>The original Bambu Lab spool holder works well but takes a lot of filament and is missing a few nice features, such as being able to see how much filament is left on your spool, having passthrough holes for respooling, and more places to stick the loose end of your filament. </p><p>The original locking mechanism is unchanged, and these will work interchangeably with the original version if you only want to do one side or something. The lock tab is still there for accepting the Bambu Lab refills and the original shims work as well if you want the extra locking power. </p><p>I would recommend you print this in something that can withstand a dehydrator. I used ASA.</p><p>I printed in 0.2mm layers without supports, with a light glue coating on the bed for ASA. </p><p>&nbsp;</p><h3>Descrizione Modello</h3><p>La versione "v2" non ha un'area per l'etichetta nel caso in cui desideri risparmiare ancora più filamento. Altrimenti stampa le versioni “v3”.</p><p>Il porta bobina originale Bambu Lab funziona bene ma richiede molto filamento e manca alcune caratteristiche interessanti, come la possibilità di vedere quanto filamento è rimasto sulla bobina, avere fori passanti per il riavvolgimento e più posti dove attaccare il filamento sciolto estremità del filamento.</p><p>Il meccanismo di bloccaggio originale è invariato e funzionerà in modo intercambiabile con la versione originale se vuoi fare solo un lato o qualcosa del genere. La linguetta di blocco è ancora lì per accettare le ricariche Bambu Lab e anche gli spessori originali funzionano se desideri un potere di chiusura extra.</p><p>Ti consiglierei di stamparlo in qualcosa che possa resistere a un disidratatore. Ho usato l'ASA.</p><p>Ho stampato in strati da 0,2 mm senza supporti, con un leggero rivestimento di colla sul letto per ASA.</p>

Bambu Lab Reusable Spool Holder

3d打印机配件

laisch

<h3>HUGHES MD - 500 (flyable pullcopter) </h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_sman5x65txu7.gif"></figure><p>&nbsp;</p><p>&nbsp;</p><h3>Externals</h3><p>For launching the MD-500, you need to make the “<a target="_blank" href="https://makerworld.com/de/models/81500" rel="nofollow noopener">Overpowered Heli Launcher</a>” before:</p><figure class="image"><a href="https://makerworld.com/de/models/81500" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_cmrmg9lwcdhu.jpg"></a></figure><p>&nbsp;</p><h3>Printingsettings</h3><p>Print as light as possible. I used 2 perimeter, 0.2mm layerheight and 10% infill on the helicopter body.</p><p>For the Rotor use Arachne in the slicer.</p><p>&nbsp;</p><h3>Postprocessing</h3><figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_n770l86x94u8.jpg"></figure><p>Clean the hole for the shaft with an 8mm drill bit. Make it as clean as possible to avoid friction.</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_41bpt3jnpijj.jpg"></figure><p>Add the pins to the body and glue the two haves together with some superglue</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_bb2k67jpmjiq.jpg"></figure><p>Add a drop of superglue into the skid holes and glue the skids in place</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_huhj8w7d9shl.jpg"></figure><p>To make the helicopter fly stable, you have to direct the airflow of the propeller to act as a counterforce against the rotors spinning direction. The easiest way is to make a fin with transparent tape.</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_i9cggf52mewy.jpg"></figure><p>You have to adjust the sice and angle of the tape according to your friction on the shaft</p><p>Testfly -→ adjust → repeat …</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_61dldorkdcxe.jpg"></figure><p>Mount the rotor to the shaft. It should be friction fit, but if its too lose you can add some superglue. (The rotor should spin freely)</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_etlatpk1760y.jpg"></figure><p>To stop the helicopter from rotating during the launch, you have to add the helistops to your launcher. Just remove the old M3x6 screw and replace it with a M3x10.</p></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_7efl5p749tfj.jpg"></figure><p>Have Fun</p></td></tr></tbody></table></figure><p>&nbsp;</p>

收纳小物

3d打印机配件

玩具