ToM_Korn

michelem

Welcome to our cozy Midcentury Modern Birdhouse!&nbsp;It&#39;s not just a home for birds – it&#39;s a stylish retreat full of cool features like a Wifi enabled camera for birdwatching and more!&nbsp;Around the house, you&#39;ll find cool stuff like a modern textured panel, tiny cacti, a cute wooden-effect wall, a pergola for shade and a handy tray for seeds or plants. There&#39;s even a pop of color with a fun angular piece!&nbsp;Of course, there&#39;s a 35mm entrance and a little perch for our feathered friends.&nbsp;But the coolest part? The roof has a big opening covered by a magnetic box that looks like a mini terrace. It&#39;s not just for looks – you can put a plant in it with the &#34;Terrace Box&#34; component or add a WiFi camera with the &#34;Blink Support&#34; part to see what the birds are up to!&nbsp;It comes with mounts for walls or poles, so you can place it wherever you like.&nbsp;Printing it is easy but takes a bit of time. Since it&#39;s for outdoors, use tough materials like PETG, ABS, or ASA is recommended. PLA might fade or warp in the sun.&nbsp;You&#39;ll need screws, bolts, inserts, and magnets – check the list below for everything you need!&nbsp;Assembling it is quite intuitive, but I have attached the complete instructions.&nbsp;To add the Wifi camera you will need a Blink device (works with Blink Outdoor 3 or 4). You could need also the Sync Module or an Alexa device to connect the camera to.&nbsp;I personally used these:&nbsp;<a target="_blank" href="https://www.amazon.it/dp/B086DKRWCH?psc=1&amp;ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">Blink Outdoor Camera</a> <a target="_blank" href="https://www.amazon.it/dp/B084RPZGR2?psc=1&amp;ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">Blink Sync Module</a>&nbsp;NOTE:It&#39;s recommended not to install the birdhouse in direct sunlight, especially if equipped with the WiFi camera. Best place would be under a tree or similar.&nbsp;Dimensions&nbsp;The base is 25cm x 20cm. The house with terrace is tall about 19cm max.&nbsp;Unfortunately, I&#39;ve just finished and mounted the first one, so I don&#39;t have any videos of our little friends to show you yet. However, here&#39;s a peek inside with the camera:&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000468694/design/2024-05-19_c9dc902e65eab.jpeg"></figure>Get ready to enjoy building your birdhouse and making new feathered friends!

Modern Midcentury Birdhouse - Wifi Camera enabled

home

潦草小狗爱吃雪糕

This is a mold for making spinning top from PLA filament purge. The tops made with this mold are very colorful and spin well. I printed the mold with PETG at 100% infill and did not need to use supports (PC might work even better).&nbsp;What you will need:<ul><li>An unused oven</li><li>A silicone mat (it&#39;s easier to flip and roll the melted PLA into a ball on a silicone mat than on a metal baking tray)</li><li>PLA filament purge</li><li>A 3M respirator or N95 mask (the fumes from melting PLA in the oven are stronger, so please protect yourself)</li><li>Work gloves</li><li>Tongs</li><li>Pliers</li><li>A digital scale</li></ul>Process：1. Accurately weigh 6g of PLA filament purge and place it in the oven.Preheat the oven to 200-230°C and heat the filament purge for approximately 5 minutes.2. Use tongs and pliers to shape the melted PLA into a ball. Evenly folded patterns will look better.3. Place the shaped plastic into the mold and press the mold firmly.4. After approximately 3 minutes, open the mold and remove the top. If the top is difficult to remove, use pliers to take it out.「Twisting and shaking the mold after it has cooled completely can aid in part release. I recently tried using a mold release agent (spray), and it has been very effective in ensuring smooth part separation.20240512」（translate from Google Gemini）&nbsp;&nbsp;这是一个使用PLA耗材废料制作陀螺的模具，制作出的陀螺颜色比较漂亮，旋转的很好。我用PETG 100%填充来打印模具，无需添加支撑（PC可能效果会更好）。&nbsp;你需要：一个闲置的烤箱，一个硅胶垫（需要把熔化的PLA翻折并团成一团，这在金属烤盘中很难操作），PLA耗材废料，3M防毒面具或N95口罩（在烤箱中熔化PLA产生的气味更大，请做好防护），工作手套，取盘夹，钳子，电子秤。&nbsp;压模步骤：&nbsp;1，将 6g（请准确称重）PLA耗材废料放入烤箱中，200～230℃加热约5分钟（烤箱需预热）<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_df4dbe446d418.jpg"></figure><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_74bd4a7599ef7.jpg">&nbsp;&nbsp;2，用取盘夹和钳子把熔化的PLA团成一团（翻折均匀的纹理会更漂亮）<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_31b36cc45d107.jpg"></figure>&nbsp;&nbsp;3，把团好的塑料放入模具中，用力挤压模具。&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_75a96c8b0fc52.jpg"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_06f1d6fa28797.jpg"></figure>&nbsp;&nbsp;4，大约3分钟以后打开模具取出陀螺。如果脱模困难可以用钳子把陀螺取出。<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437241/design/2024-04-21_07f0433aa2577.jpg">&nbsp;&nbsp;「充分冷却后扭转并晃动模具将有助于脱模。我最近尝试使用脱模剂（喷雾），它很有效，可以确保顺利脱模。20240512」&nbsp;

Spinning top mold   陀螺模具

presents

Memel Magic

<h2>Mary Jane kissing Spiderman</h2>If you want quality as in photo,use 0.2mm nozzle, with 0.06mm layer height.

Radioactive Love

resin_print

Wcad00

UPDATE 9 - 25.03.2024<ul><li>updated profile REQUESTS - added plate 17 - user @gurthyy  wanted a new module to accomodate a mac mini on its side - added a new two space combo module for mac mini and keyboard/mouse</li><li>updated profile REQUESTS - added plate 18 - user @wmeringolo wanted a new module for miniature painting  - added a new combo module for cup + brushes</li></ul>&nbsp;UPDATE 8 - 16.03.2024<ul><li>updated profile REQUESTS - added plate 13 - user @bambibam  wanted a new combo 1x module for sd/ microsd/usbA/ usbC  - so there is a new combo module available</li><li>updated profile REQUESTS - added plate 14,15,16 - user @gurthyy wanted a way to angle the organizer after specific desktops - introducing Pizza Slices - angled 30degrees modules coming in two snap-on formats for now, but with room for much more customisation. Plate 14 has the universal pizza slice base + simple catch all top; plate 15 has an split/organized top, and plate 16 has a slide-on interchangable name plate - see photos in print profile. Everything was printed and tested for a perfect fit - check photos</li></ul>UPDATE 7 - 05.03.2024<ul><li>updated profile ACCENTS - user @Xanders_Builds noticed an issue i missed with the ‘’steps' accent brims not fitting corectly - too loose - now it is updated and fits fine</li><li>updated profile REQUESTS - added plate 10 -one new module  ASP @user_2207529250  and @bluebeansisradi requested a stand for a ps5 and xbox controller - new module that occupies two spaces and needs to be snapped into place - stand for ps5 and xbox controller - i tested a ps5 controller but i dont have a xbox, but it has some tollerance so it should fit fine - in case it does not, i made the module from two parts , so the stand can be exchanged - please let me know if that is the case</li><li>updated profile REQUESTS - added plate 11 -one new mod  for DRAWER MAX. user @Nerraw asked for a method of separating the drawer into smaller spaces - i made a very simple method of doing that - 4 interconnectible separators that can also be printed individually or by neccesity i guess</li><li>updated profile REQUESTS - added plate 12 -one new module User @zach13 asked for a method of organizing documents vertically so this is my take on it. The iddea was to make it sturdy because it is a little tall and not to waste too much material - it is made from 3 pieces - a base plate and to organizing stands that fit slightly different from each other so that the papers will stay a little cuved to maintain vertical position</li></ul>&nbsp;UPDATE 6 - 15.02.2024<ul><li>updated profile REQUESTS - added plate 7  - Reinforced top plate for the DM. @bosho.liviu requested a top plate so modules could be placed on top - Now you can do that, it is symetric and compatible in every direction</li><li>updated profile REQUESTS - added plate 8,9  - Two new modules . @bdwilson asked for two modules that have removable interior trays - plate 8 has a new 1space tray module and plate 9 has a new tilted marker combo with one large tray on the bottom. The front part of the removable tray is also slanted for easy removal</li></ul>&nbsp;UPDATE 5 - 11.02.2024<ul><li>updated profile REQUESTS - added plate 5  - Tough Plate for the DM. @Heimwerkerbienchen requested a tougher top plate so monitor could pe placed on top of the DrawerMax - has all the toughness required bells and whistles but i really cant guarantee how it will hold up in time - in my oppinion the entire assembly should be printed in a tougher filament, because altough the new plate has a support structure, the drawer modules themselfs are pretty thin so the weight of the monitor will be on the walls</li><li>updated profile REQUESTS - added plate 6  - Half Bow ties. @bdwilson had a very good ideea to close the holes on exterior modules so introducing half bow ties </li></ul>&nbsp;UPDATE 4 - 28.01.2024<ul><li>updated profile REQUESTS - added plate 4  - Steps + Tape dispenser combo unit. altough it was not a request, the plate has the name of the user that gave me the ideea - thank you for that @lilrepete</li><li>the new module is compatible with existing ACCENTS, plus the security wheel and the blade can be printed in other colours to keep things fresh</li><li>the blade slides into the module and is interchangable in case teeth break or you just want another colour. if you feel it fits too tight just trim the seam of it and it will slide more easily</li></ul>UPDATE 3 - 23.01.2024<ul><li>updated the printing order to outer/inner - not a big issue but some had problems - now all is well</li></ul>UPDATE 2 - 22.01.2024<ul><li>added a new print profile called ACCENTS</li></ul>In keepign with the modularity theme and ultra customizability i aim to develop, i made some mix or match brims to add an extra touch of colour to your organizer. everything fits in place without glue or force and same as everything else it is easily changable in case you want to switch up your look and keep it fresh.photos attached in the profile so please check them out. i know the colours i actually printed are not the best but it was all the filament i have till i get my new shipment&nbsp;UPDATE 1 - 19.01.2024<ul><li>added a new print profile called DRAWER MAX</li></ul>it is a drawer module that occupies 4 slots, is stackable and also highly customizablethe first tray for it, as you can see in the pictures is for the spare parts that come with the BambuLab printer + some extras. Fits the parts for two printers.make sure you follow the instructions in its profile to get perfect fits everywhere<ul><li>added a new print profile called REQUESTS</li></ul>this profile contains the user requests for modules. each plate will have the users name on it. this is going to be the profile i will update regularly, based on requests.&nbsp;&nbsp;I’ve been wanting to do this project since I made the first desktop organiser.The problem I wanted to address was, what if in a month you want or need something else, more, or less space, something specific, more room for usb, cards, crayons, etc, how do you keep a new look with minimal to no effort?&nbsp;I’ve seen there have been many attempts to do this but none really took of, so I asked myself why? I think the main reason was lack of interest derived from lack of support. If newer modules aren’t created, interest goes down, and it becomes the same thing as a normal organiser.Of course we have the gridfinity system witch is great honestly and other similar to it, but they all rely on the same premise, a base to keep everything together, so if you are full, you need another base, but does the base you need right away exist? or are you going to be left with extra slots.&nbsp;Maybe I didnt do my research right, and there are other options, all I tried to do was to make something universal, easy to print, elegant, very customisable, and most of all, something that doesn’t depend on screws, magnets and on a base to keep it all tied. I printed 10 bowties In less than 20 minutes on standard, and hold together 7 modules (the ones I use) and you can lift and move them as a whole, without having them fall or break&nbsp;The bow tie joint isn’t my ideea, it’s been used in woodworking for centuries. It is a robust way of holding things together and works quite well here too, especially printed the way I arranged it on the plates . All the modules can be connected in whatever orientation you want, except the laptop stand, because it needs room on the small sides for the length of the laptop/tablet. But that is it - I kind of made that specifically for me, because I use it as an end piece that fits under my P1S (like my first organiser)&nbsp;I am starting with 12 modules and will make a new one every other week, based on suggestions I hope, because I dont think I have enough creativity. I will put out my own ideas because I do have more, but everyone has diferent needs so if you think you can get on board with the ideea I welcome all input, and I will try to make whatever you want. Remix culture is strongly encouraged.&nbsp;Modules in the 3mf:&nbsp;PLATE 1<ul><li>Usbcombo1 (11 usb sticks + 5 full size memory cards + tray for usb caps)</li><li>Phone combo (fits iphone 15 promax + airpods pro)</li><li>Post-its (two full size stacks of postits)</li><li>Steps (4 equal holders - superglue, ties, hex set, mini uv lamp)</li></ul>PLATE 2<ul><li>12 bow tie joints - enough for about anything</li></ul>&nbsp;PLATE 3<ul><li>Hex single - roomie organizer - can be further split with the splitters on plate 8</li></ul>&nbsp;PLATE 4<ul><li>Laptop wedge - macbook pro + ipad pro 12.9 + apple microfiber slot - made to be wedged under the x1 or p1</li><li>Laptop standard - - macbook pro + ipad pro 12.9 + apple microfiber slot + additional slot</li></ul>PLATE 5<ul><li>Tilted marker combo - 12 thick markers + pens and other + paperclip 3 + misc tray</li></ul>PLATE 6<ul><li>apple watch dock double - 2 apple watch charger pucks - like the original - cable management + full size post it tray</li></ul>PLATE 7<ul><li>Hex double - double the size of the single - can be further split with the splitters on plate 8</li></ul>PLATE 8<ul><li>5 split plates for the hex series</li></ul>PLATE 9<ul><li>apple watch dock single - 1 apple watch charger puck - like the original - cable management</li></ul>PLATE 10<ul><li>Usbcombo A - 6 usb sticks + 5 full size memory cards + tray</li></ul>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

The Organizer

Ordnung!

SThane

After printing a couple other models that didn't seal properly, I decided to pick a well-designed model and make a few changes to seal it as much as possible. There are now three versions of the tray:<ol><li>The first version can be printed face-up, and does not include the logo.</li><li>The second version is multi-color, and meant to be printed face-down, to maximize quality and minimize filament swaps.</li><li>NEW! - The third version addresses the most common feedback - make it stronger, and make it work with the original AMS Lids</li></ol>For the first two, I've reinforced the desiccant opening, provided an improved snap-fit lid with a tab to indicate the proper orientation, updated the funnel adapter to fit into the container better, added the funnel, and added brims to the two funnel parts. The funnel can also be use with this <a target="_blank" href="https://makerworld.com/en/models/28349#profileId-24748" rel="nofollow noopener">AMS Desiccant Pod</a>. &nbsp;For the third design, I've made the desiccant tray shorter, and inset the lid, to make it flush, and so it can be concealed behind the original AMS lid. I've also made the desiccant openings deeper, so that the top is much sturdier.&nbsp;Note: See the attached photos for the best way to insert the lid. If you insert the left or right side first, then press the other side, you risk breaking the model. Please insert the edge closest to the logo first, then push the tab back towards the other tab. It may be a bit snug, but if you insert it at a slight angle the first time, you can then easily slide it into place.

Sealed AMS Rear Desiccant Tray

3D Printer Accessories

AMT_MW

<h2>What it is</h2>A three digit life counter with a small compartment inside, a screw on lid and detents for the number positions.It is part of a design family, so you do have more options if you want it a bit different:<figure class="table"><table><tbody><tr><td><a target="_blank" href="https://makerworld.com/models/26050#profileId-22466" rel="nofollow noopener">2 wheels</a></td><td>3 wheels</td><td><a target="_blank" href="https://makerworld.com/models/136390#profileId-148342" rel="nofollow noopener">4 wheels</a></td></tr><tr><td><figure class="image image_resized" style="width:62.74%;"><a href="https://makerworld.com/models/26050#profileId-22466" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/394769/2024-01-08_c088fc921dfab.jpg"></a></figure></td><td><figure class="image image_resized" style="width:45.18%;"><img src="https://makerworld.bblmw.com/makerworld/draft/394769/2024-01-08_547b5c0ced69c.jpg"></figure></td><td><figure class="image image_resized" style="width:59.5%;"><a href="https://makerworld.com/models/136390#profileId-148342" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/394769/2024-01-08_692abd2283447.jpg"></a></figure></td></tr><tr><td><a target="_blank" href="https://makerworld.com/models/26050#profileId-22466" rel="nofollow noopener">Life Counter 0-99</a></td><td>You are here :)</td><td><a target="_blank" href="https://makerworld.com/models/136390#profileId-148342" rel="nofollow noopener">Life Counter 0-9999</a></td></tr></tbody></table></figure><h2>How to print</h2>For multicolor printing and convinience, a 3MF file is provided. There are several modifiers present, deactivate or change them to get your desired outcome.<figure class="image"><img src="https://media.printables.com/media/prints/709800/rich_content/a39f2575-9bcd-4dff-85f3-781f92a7e9df/thumbs/cover/800x222/png/image.webp"></figure>Recommended for printing is a layer height of 0.16mm and a 0.4 mm nozzle, but up to a layer height of 0.2mm and a 0.6mm nozzle the results have been surprisingly good as well.&nbsp;The optional text on the lid or Axle (like HP & XP) simply is added via the text shape tool of the slicer. Any font you have installed is possible.<figure class="image"><img src="https://media.printables.com/media/prints/709800/rich_content/dc4dd686-4908-4a4f-95a4-5a1a2b5d0e0f/thumbs/inside/1920x1440/png/image.webp"></figure>Material at one's discretion, I opted for PETG and 25% infill.Scaling it down is possible, if smaller than 60% the tolerances may become a problem.<h2>Without MMU or AMS</h2>If not already printed as multicolor, nail polish or model paint works well to highlight the glyphs. For text on the axle or lid a manual filament swap is advised, using the text shape tool to emboss your text may also be an option.<h2>What next</h2>There may be improvements and modifications based on feedback given here.Maybe, take a look at <a target="_blank" href="https://makerworld.com/u/2797532051" rel="nofollow noopener">my other designs</a> ;-)

home

presents

resin_print

Ordnung!

3D Printer Accessories

DnD