mojo哒哒哒hhh

schutz

Use this vent cover / grille to cover the open air vent underneath the driver and passenger seats in your Model 3. This keeps small objects from falling into the air vent, while having a thin grille profile so it does not disrupt airflow. This is confirmed to fit on 2018-2023 Model 3 vehicles, but I do not know about 2024+.&nbsp;To install, move the seat all the way forward and up to reach the open vent duct. The tabs on the edge will hold the grille in place.&nbsp;PETG is recommended as it tolerates some flex as well as temperature changes. 0.20mm Standard profile works well.

Tesla Model 3 Floor Vent Cover Grille

Tesla

ruimach

<h2>Summary</h2>Hello!&nbsp;So, it was that time again, another broken phone holder. They work ok for a while but after some time they just are made to be replaced by a new one…&nbsp;So I decided to put my 3D cad design skills to the test :) Actually, this resolution happened in September of 2021, one month after I bought my 1st 3D printer and this was my 1st "big" project. This design was in beta test in my car for the past year, and, not being perfect, I'm happy with it (more important than me being happy, my wife is also :D ), so I'm releasing it to the community.&nbsp;Small disclaimer, but important one: this was made for a 2014 Renault Megane. It is possible that it will work for your car or not… The part that connects to the car might have to be redesigned for your needs.&nbsp;This is a Glue needed build.&nbsp;It will also require 1 rubber band.&nbsp;Printing Instructions:&nbsp;Don't use PLA. A car in the sun will heat up a lot. PLA is not going to survive it.&nbsp;Material: PETG (or similar)Infill: 15%Supports: NoChange filament during print: Only if you wantBrim: Not neededRaft: No&nbsp;All models are print ready oriented.&nbsp;You can choose between a cover with or with logo.&nbsp;You need to print 2 pins.&nbsp;Assemble Instructions:&nbsp;Start by inserting the left, right and bottom support in the box.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/354852/2024-01-05_cf2bca0fa8cad.png">&nbsp;&nbsp;Then fit the 2 pins to connect the left arm to the bottom support and the right arm to the bottom support.&nbsp;This way when there is height in the bottom, the arms will hug the mobile phone, locking it in place.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/354852/2024-01-05_ccbe0e655108d.png">&nbsp;The movement in the beginning can be a little hard. Move it up and down a few times until you have a smooth movement.&nbsp;Now the rubber band part, place it between the mark spots bellow:&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/354852/2024-01-05_b912311830277.png">&nbsp;In the end you should have something like this:&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/354852/2024-01-05_e893b53a7f617.png">&nbsp;At this stage, you should test it with your phone. This will validate if the rubber band is to strong or not. A too strong rubber band will prevent the mobile phone to trigger the arms to lock the phone in place. If that is the case replace the rubber band until the setup works.&nbsp;Then you need to glue the cover in. Little grooves were made in the box to help the task. Carefull not to glue the arms or the bottom support.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/354852/2024-01-05_575b4d562f7a1.png">&nbsp;&nbsp;Finally the car connector. In the back of the box there is a groove where the connector will be glued:&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/354852/2024-01-05_fb988f5432471.png">&nbsp;After that is done you can now attach it to your car (if it fits, see disclaimer above).&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/354852/2024-01-05_33674440d8ef2.png">&nbsp;After inserting it in the lock it in place with the screw.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/354852/2024-01-05_43c3a7b766d98.png">&nbsp;&nbsp;Hope it works for you as well as it did for me.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/354852/2024-01-05_6ff76af6df149.jpeg">&nbsp;&nbsp;<h2>Print Settings</h2>Printer Brand: Creality Printer: CR-10&nbsp;Rafts: No Supports: No&nbsp;Resolution: .2 Infill: 15&nbsp; Filament: <a target="_blank" href="http://www.amazon.com/s?url=search-alias&field-keywords=Any+PETG" rel="nofollow noopener">Any PETG </a> Any

Car Phone Holder

手机支架

laisch

With this handy little tool you can clean your carbon rods even when the lid of your bambulab printer is closed.Just put Isopropyl alcohol on the sponges, snap it to your carbon rod and move it back and forth a few times till they are shiny again.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/251911/2023-12-07_e4ey6ohuzxon.gif"></figure>&nbsp;<h3>Postprocessing</h3>For the sponges you can use a normal kitchen sponge (be careful to not use the abrasive ones). Cut two pieces roughly about 10x20x20mm and press them into the spongeholder.For the pullback mechanism you can either print the provided spring in TPU, or use small hair rubberbands. The spring also works in PETG but looses its strength from time to time.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/251911/2023-12-07_g1k0c2tnzlwn.jpg"></figure>&nbsp;&nbsp;More info about cleaning the carbon rods can be found in the <a target="_blank" href="https://wiki.bambulab.com/en/general/carbon-rods-clearance" rel="nofollow noopener">Bambulab Wiki</a>

Tesla

手机支架

工具

ab