宜家洞洞板ikea

Mr__X_

The idea to design and build this has been with me for a while, and I finally got the time to do it….&nbsp;What is it?&nbsp;This is a fusion of the Bambu Lab AMS Lite and the Filadryer S4 by Sunlu. First and foremost it will allow you to keep your filament dry and also print directly from the Filadryer but with AMS Lite capabilities. Second, you will clear up space on your desk (if you previously had the AMS Lite standing on it). You will also get a tray on top to store some stuff.&nbsp;<figure class="media"><div data-oembed-url="https://youtube.com/shorts/2Q9C1bFs7RI?si=E8K7lpsVw9x-isAr"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=2Q9C1bFs7RI"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/2Q9C1bFs7RI" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>&nbsp;Lets get to it!&nbsp;My list of prerequisites were:<ul><li>All functionality of the AMS lite should persist.</li><li>All functionality of the Sunlu S4 filament dryer should persist.</li><li>No modification or damage to the original parts of both the AMS Lite or Sunlu S4 allowed. (reassembly must be possible)</li><li>No or at least minimal supports required when printing.</li><li>Only printed parts allowed, no additional parts (like screws, bearings, etc) should be required.</li><li>As much as possible of the design to be "mirrored".</li></ul>All plates and parts needed are stored in the 3mf-file. I used a X1C to print the parts. I opted for ABS since it usually gives great durability and finish. It will most likely work with PETG or even PLA, but I have not tried that, and PLA might be insufficient in drying temperatures.&nbsp;For a smooth journey I would start like this and print:<ul><li>BASE A</li><li>BASE B (Exactly the same as BASE A)</li><li>CLIPS & LOCKS & PLUGS</li></ul>While printing, disassemble the AMS Lite. There are guides for this in the wiki:<a target="_blank" href="https://wiki.bambulab.com/en/ams/maintenance" rel="nofollow noopener">AMS Maintenance and How To guides | Bambu Lab Wiki</a>&nbsp;To remove the feeder units, unscrew the four screws that are attached to the main body and unplug the to ribbon cables from the mainboard. The feeder units does not require any further disassembly.When you have removed the motherboard (Details in the wiki), carefully remove the NFC sensor windings from the main body. Easiest way to do this was to use a screwdriver and bend carefully at each place where there is silicone, It is four places in total for each sensor.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_a3d4f5fbdc08e.png">&nbsp;That's all AMS parts you need to disassemble. You should now have this in front of you<ul><li>First stage feeder kit</li><li>1x Motherboard</li><li>4x NFC Sensor windings</li><li>4x rolls</li></ul>Now turn to the Sunlu S4. The top covers needs to be removed. I was puzzled of how to to this but found out that if one cover is opened and then carefully bent, it would snap out from the chassis.&nbsp;When you have finished printing the first three plates print the following plates:<ul><li>LEG A</li><li>LEG B</li><li>YELLOW SPOOL HOLDER (x2 on the plate)</li><li>GREEN SPOOL HOLDER (x2 on the plate)</li><li>LEG C</li><li>LEG D</li></ul>(All LEG parts are exactly the same)&nbsp;Assembly of the SUNBU AMS LITE main body&nbsp;BODY A and BODY B will jack in to each other. Just pair the edge at an angle and twist them together:<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_ab52ec925e33f.jpeg">--→&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_785927e1c5f86.jpeg">&nbsp;Now find the following parts from the CLIPS & LOCKS & PLUGS plate:<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_f0e7b8cbb5b4d.png">&nbsp;Push the three H-shaped slips into the main body. You can use the rear side of a screwdriver for this. Or any other tool you like. Or just toyr thumb. Note that the clips have a chamfer on one side. That side is the one that goes into the model.<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_e8e15130f15ed.jpeg">&nbsp;Now turn to the two small 6x10mm poles. Drop one sideways into each of the slots on the top side of the main body. Use a screwdriver and push the pole into the next part of the main body. Press it all the way in.<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_a39dbaa46ddfe.jpeg"><img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_a57c1e7d4572d.jpeg">&nbsp;Now take the two "lid-blocks" and push down one in each hole<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_9e4e233ce63ba.jpeg">&nbsp;If you have finished printing the next 4-6 plates you can start assembly of the legs.While doing so print the following plates:<ul><li>FIRST FEEDER STAGE MOUNT & MB HOUSING</li><li>SENSOR COVER A</li><li>SENSOR COVER B (Same as SENSOR COVER A)</li><li>HANDLE A</li><li>HANDLE B (Same as HANDLE A)</li></ul>this should conclude the printing of parts.&nbsp;Assembly of the legs&nbsp;From the CLIPS & LOCKS & PLUGS plate find the 4 squared lock-platesTake one LEG-part and slide it into the lock plates that you will have to put in from below. The easiest way to fit the legs is to start with one lock plate and just get it to attach enough to hold it in place. After that do the same with the second lock plate and finally slide the legs as much as it allows for. (Never mind the yellow cross below the leg, I did assembly in a different order that was not optimal)<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_825180773f66b.jpeg">&nbsp;Grab the YELLOW SPOOL HOLDER and push it through the first leg half<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_c0abec028a4b7.jpeg">&nbsp;IMPORTANT!The spool holders must be inserted to the correct leg half, otherwise to rollers will not be oriented correctly. If installation is done as in the pictures you will be fine!&nbsp;Now, push the GREEN SPOOL HOLDER through the second leg part<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_c514f6683f1a9.jpeg">&nbsp;Take the second leg half and push it to align with the first leg half.<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_13be645e3bec.jpeg">&nbsp;From the CLIPS & LOCKS & PLUGS plate find the 28 clips (4mm thick)From this point there is no turning back, you will not be able to disassemble the legs after this without drilling all clips so:MAKE SURE YOU HAVE THE ORIENTATION OF THE YELLOW AND GREEN SPOOL HOLDERS CORRECT!&nbsp;If you have the main body laying upside down in front of you, there should always be a YELLOW SPOOL HOLDER on the top right corner.&nbsp;Put clips into the leg by pushing it into the holes. The clips have a chamfer on one side that goes into the leg.<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_7a028f944acf1.jpeg">&nbsp;When you have assembled one leg do the same procedure with the other leg.Note the orientation for GREEN and YELLOW SPOOL HOLDER!!!!!! (See complete assembly 3 pics below)&nbsp;Install the NFS sensor windings for each roll and pull the wire through the hole in the base plate.<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_b9bd81372a6ab.jpeg">&nbsp;Install the sensor covers by pushing them down into the shaft<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_99bcb5cad7926.jpeg">&nbsp;&nbsp;The result should look something like this:<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_622813e08e507.jpeg">&nbsp;Now, mount the original spool holders, It might take some convincing, but they will fit eventually…<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_8aa8596def4cb.jpeg">&nbsp;Add some rolls of filament, or don't. It's up to you, it was my way of getting the assembly to be able to turn over and rest horizontally while assembling the rest. A different option is to place it in the Sunly S4…<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_f21f65277dd82.jpeg">&nbsp;Attaching and connecting the motherboard&nbsp;There is a surplus of mounting points for the motherboard due to the mirrored design of the parts. Some of the surplus mounting points needs to be cut away (use a sharp plier). You will realize which ones that needs to be kept. The motherboard is mounted upside down.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_733dde974bb1c.jpeg"><img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_d46dca89eac79.jpeg">Note the arrangement of the ribbon wires. (B/W to the left), And also the numbering I did on the motherboard. It is the corresponding sensor wire for the NFC sensors.&nbsp;We have now come to the point of mounting the housing for the motherboard. Locate the parts printed on the FIRST FEEDER STAGE MOUNT & MB HOUSING plate and take one of the MB Housing parts, and slide it onto the rails of main body. Make sure to keep the ribbon wires out of the way,<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_4f7143f9474ad.jpeg">Do the same thing with the second mb housing part<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_f4299c08f864b.jpeg">&nbsp;Slide the two AMS Interface units into place<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_a93ba0933f5fa.jpeg">&nbsp;Screw the AMS first stage feeder assembly into place. make sure that the numbering of the feeders cohere to the numbering on the mainboard.<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_13fd979fcfee.jpeg">&nbsp;Assembling the handle&nbsp;Locate the grip lock and grip interface from the CLIPS & LOCKS & PLUGS plate:<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_2790f9516f092.png">&nbsp;I don't have pictures of this, but it is more or less the same procedure as when mounting the legs.Locate HANDLE A & HANDLE B. They look the same (and are identical in design)<ul><li>Attach one of the handles to both grip interfaces by sliding them</li><li>Attach the other handle to both grip interfaces by sliding them</li><li>Locate the grip clips (x18) from the CLIPS & LOCKS & PLUGS plate</li><li>Push all 18 clips into the handle</li></ul>Now you have a grip assembly in your hand that should enable you to:&nbsp;Push each of the grip interfaces through the holes in the main body and use the grip lock (the bar) on the other side to keep them in place. I used a water plump pliers kind of tool to push the bar into the right place. As explained before, I initially did this assembly in a different order, hence no legs are present in this pic:<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_150e61e4525d3.jpeg">&nbsp;The result should look something like this (But with more clips installed):<img src="https://makerworld.bblmw.com/makerworld/draft/451566/2024-01-24_6f44a4dd3dd77.jpeg">&nbsp;So, final touch. And yes, I know, it contradicts my prerequisites since it adds additional parts, but it is optional;<ul><li>For each first stage feeder, put a small PTFE tube trough the main body. It will simplify the loading of filament…</li></ul>There are some models on the CLIPS & LOCKS & PLUGS plate that you can use to plug unused holes in the base.&nbsp;Final Notes&nbsp;If you are to print TPU it is (as you most likely know) not supported by the AMS Lite. In that case remove one of the original rollers from the Sunbu AMS Lite and feed the TPU through one of the standard filament holes of the filadryer S4. The roll will then rest on the original rollers of the S4.&nbsp;I think I covered all now. If not, let me know….

SUNBU LAB AMS LITE 1.0

A1配件

N3komata

螺丝刀套装为威克士软轴套装的螺丝刀组 套装咸鱼24 非常超值，固定螺丝刀的固定件请用tpu打印并用胶水粘上。盒盖和盒内的圆孔用于安装直径3mm 厚度1mm的磁铁 文件已经留出了公差 可放心打印

精修螺丝刀套装盒

收纳盒

Montel

适用于worx小脚版电池的DIY取电底座, 接插件可用6mm汽车端子，用途多多. 献给喜欢捣鼓的小伙伴：）

WORX威克士 适用于worx小脚版电池的DIY取电底座

锂电工具

StlCraft

<figure class="table"><table><tbody><tr><td style="background-color:hsl(0, 0%, 0%);">I have added a version with the heart separated from the body to make it easier for you with printing.</td></tr></tbody></table></figure><blockquote><h3> I'm just getting started, follow me please! </h3></blockquote><figure class="table" style="width:97.18%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td style="background-color:hsl(0, 0%, 90%);"> 🌟 Welcome to the community! 🌟&nbsp;Are you a shop and do you want the commercial rights to the models? Do you want to receive 4 unique models for a few users?Take advantage of the offer 5 dollars per month for the first 100 users. &nbsp;<figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/539553/2024-02-15_77e50735e01fa.png"></figure></td></tr><tr><td><h2><a target="_blank" href="https://www.patreon.com/TinyMakers3D" rel="nofollow noopener">SUBSCRIBE</a></h2></td></tr></tbody></table></figure></td><td style="background-color:hsl(0, 0%, 0%);">&nbsp;New model available visit my profile. I am uploading a model every day. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/539553/2024-02-13_eeca3a450b8c.png"><figcaption><a target="_blank" href="https://makerworld.com/en/models/183775#profileId-202994" rel="nofollow noopener">DOWNLOAD</a></figcaption></figure><figure class="image image_resized" style="width:64%;"><img src="https://makerworld.bblmw.com/makerworld/draft/539553/2024-02-15_ba12aaec748b3.png"><figcaption><a target="_blank" href="https://makerworld.com/en/models/186289#profileId-205080" rel="nofollow noopener">DOWNLOAD</a></figcaption></figure>&nbsp; </td></tr></tbody></table></figure>&nbsp;&nbsp;

♡♡♡  COUPLE IN LOVE for anniversary gift. Elegant and minimalist Home decor

爱心类

Collecticraft

<h2>Interlocking Toroidal Vases: A Minimalist Masterpiece</h2>Step into the world of minimalist elegance with our latest creation: the Interlocking Toroidal Vases. This innovative set of vases features a toroidal design, seamlessly interlocking with each other to create a mesmerizing and unique visual form. Crafted with precision and attention to detail, these vases are a true testament to the beauty of simplicity in design.<h3>Key Features:</h3>Toroidal Design: Inspired by the torus shape, these vases boast a sleek and modern aesthetic that is both captivating and versatile. The interlocking design allows for endless configurations, making it easy to customize and adapt to any space.&nbsp;Minimalist Elegance: With clean lines and a minimalist silhouette, these vases exude understated elegance. Whether displayed individually or as a set, they make a striking addition to any home decor.&nbsp;Versatile Usage: Perfect for showcasing fresh blooms, dried flowers, or simply as standalone decorative pieces, these vases offer endless possibilities for styling and arrangement. Use them to add a touch of sophistication to your living room, dining area, or workspace.&nbsp;Elevate Your Space: Transform your home decor with the Interlocking Toroidal Vases. Whether displayed as a set or individually, these vases add a touch of modern elegance to any space. Elevate your interior design and create a statement-worthy display with this minimalist masterpiece.&nbsp;Join the Movement: Join us on <a target="_blank" href="https://www.patreon.com/CollectiCraft" rel="nofollow noopener">Patreon</a> to gain access to exclusive designs, commercial license, including the Interlocking Toroidal Vases and other innovative creations. Your support allows us to continue pushing the boundaries of design and craftsmanship. Let's create something extraordinary together! ✨🏡

Interlocking Toroidal Vases: A Minimalist Masterpiece

花盆笔筒类

水世界水族馆gokumine

使用可口可乐塑料瓶。Use Coca-Cola plastic bottles.

狗狗猫咪饮水机，Pet water dispenser.

猫咪类

SnapPrint3D_SuperCrazyPrints

Sign up Membership to get 15+ models every month. All models 3D Print Without Supports and (3MF,STL) file ready! <a target="_blank" href="https://www.supercrazyprints.com/" rel="nofollow noopener">https://www.supercrazyprints.com/</a>&nbsp;Check out my other models: <a target="_blank" href="https://cults3d.com/en/users/Scrazyone_SnapPrint3D/3d-models" rel="nofollow noopener">https://cults3d.com/en/users/Scrazyone_SnapPrint3D/3d-models</a>

Pokemon-Valentine Leafeon (NO SUPPORT)

玩偶

shuster.marc

Print main base in PETG, small piece in TPU as labeled on files. Tested on avata and flies great with hero 11 miniI wanted a quicker way to mount and unmount my GoPro or other cameras to my avata. You will need Falcam F22 quick release to make this work. To install, sandwich the TPU portion between the drone and PETG base plate. Take 4 hex screws out of quick release to remove bottom portion and mount/screw into TPU portion. Make sure screws are in nice and tight so they dont interfere with quick release sliding in and out.&nbsp;

DJI AVATA GoPro Quick Release Mount for Falcam F22 (PETG & TPU)

G3DS

Having trouble handling the tiny lid handle for your Sunlu S4 filament dryer like i do? here is my solution, now i can grasp the lid handle with 2 fingers without violence… just slide in the left and right handle sleeve upgrades, no mods or surgery needed

Sunlu S4 filament dryer LID BIG knob HANDLE UPGRADE

橙豆造物

直接下载只有支架。其余的画和字谜在原文件里，记得下载。因为参数完全不同所以没法都放再一个文件里安装和灯的教程【3D打印~中秋灯笼~为中秋做准备吧！幼儿园小学生手工作业~彩色+字谜~】 <a target="_blank" href="https://www.bilibili.com/video/BV1e34y1N7B8/?share_source=copy_web&vd_source=0f1a29922eeddb1675f64c100fd3991d" rel="nofollow noopener">https://www.bilibili.com/video/BV1e34y1N7B8/?share_source=copy_web&vd_source=0f1a29922eeddb1675f64c100fd3991d</a>&nbsp;支架用0.2默认就可以，填充打与25%

中秋手提灯笼

灯笼

9percent

Apple pencil stand. The shape is same as Apple pencil head.

Apple pencil stand

苹果配件

杰瑞爸爸的工作室

河姆渡人的杆栏式建筑，尺寸：240mm*150mm*140mm，历史教具，景观装饰

河姆渡人的杆栏式建筑

置顶

JF-699

Wanted to make a dragon coaster for the Lunar New Year. It printed quick and came out great! The bottom part is 3mm, and the upper part is 3mm. You can change the colors of the objects before printing. Happy New Year!

Lunar New Year - Year of the Dragon - Round Coaster

龙 福

Maty505

better articulated dragon. be careful when scaling down cause the tail can breake at smaller sizez. scaling up is fine.

Articulated Dragon

McFly.FPV

Mounts for Dual SMA and GPS (180 or M8Q) for FR7

FR7 - Double SMA_Antenna & GPS Mount Matek or BN180 M10 GM10 Mini V3 Flywoo FPV

穿越机配件

skywolf

龙年特辑：新年剪纸合集

剪纸

user_3882884222

宜家IKEA无限洞洞板

洞洞板

SaVo3D

Snacktray with 8 removable compartments!Make yourself comfortable and get your favorite snacks for a nice and cosy tv evening or for a get together with friends and family!For hygiene reasons only use dry snacks within the tray.You could use this model for many other purposes e.g. use the tray with the compartments for your diy projects and store screws and bolts in it or any other purpose.Before printing, make sure your build plate is clean and apply some adhesive. Wash the build plate with oil free soap and wipe it off with some paper towels. For best build plate adhesion, i use a strong hairspray. Apply a thin, even coat of it. I repeat the cleaning and reapplying of hairspray every 5-6 prints.It is an easy print, no support needed!If you wish to have more colors for the compartments like in my pictures, just arrange the compartments 1 per plate and recolor them with your desired color.&nbsp;

Snacktray with compartments

家用工具

SavageLau

&nbsp;This simple tool is fast to print, and cost very little filaments, 1.95g each.This tool will help you lube on the z and y axis (lead screw and linear rod).Extended length handle will help you easy to reach center one that within the cover.You can control the angle to push how much lube apply to the screw.<figure class="image image_resized" style="width:78.49%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_10731b083ab3.gif"></figure>&nbsp;<h3>Leadscrew:</h3><figure class="image image_resized" style="width:77.49%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_047b690a0cf77.jpg"></figure><figure class="image image_resized" style="width:77%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_0136c09e64bc8.jpg"></figure><h3>Linear rods:</h3><figure class="image image_resized" style="width:76.74%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_25301222a7901.jpg"></figure><figure class="image image_resized" style="width:76.18%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_6dbff3848e74c.jpg"></figure>

P & X Series Lube helper

拓竹小工具

akristofic

Christmas tree decorations.&nbsp;Hope you like it.

Christmas tree decorations

装饰

Hiko 3D

I share a Flareon keycap from Pokemon ⌨🐾&nbsp;From the eeveelutions series the fire pokemon is now added 🔥&nbsp;an improved version of my first Flareon design, optimized for printing multicolor and in a more minimalist style. ⭐&nbsp;You can decorate your keyboard with the different designs of hikocaps or you can give it to a friend. 😊&nbsp;This design and many more can be found on my patreon 👈&nbsp;I hope you like it! 🙌&nbsp;&nbsp;ESP:&nbsp;Les comparto a Flareon keycap ⌨🐾&nbsp;De la serie de eeveelutions ahora se agrega el pokemon de fuego 🔥&nbsp;una versión mejorada de mi primer diseño de Flareon, optimizado para imprimirlo multicolor y en un estilo mas minimalista. ⭐&nbsp;puedes decorar tu teclado con los diferentes diseños de Hikocaps o puedes regalárselo a un amigo. 😊&nbsp;Este diseño y muchos mas puedes encontrarlos en mi patreon 👈&nbsp;espero que te guste! 🙌

Flareon Pokemon Keycap

小玩意

**These designs are for personal use only. If you want to get exclusive and free designs also become an official reseller visit my patreon and join!**&nbsp; Hello everyone, I share the a new Christmas-themed knitted container: Snowman. ☃️ - It is a simple container where you can store store some candies or anything else you want to give this Christmas. 🎁🍬&nbsp;- Does not need support. Santa is printed in 4 colors with 1 AMS unit. I hope you like it and can create Snowman in different colors with the other Christmas members. ☃️🎅🦌🐱🎄&nbsp;&nbsp;&nbsp;

Snowman - Christmas knitted container

礼物盒子

Bambu Lab

This is a spool holder for Bambu filaments.

Bambu Spool

拓竹配件类

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013716/design/2023-09-25_28088e30b1c02.jpg"></figure>This 3D-printed mouse has a futuristic hollow shell design, revealing its internal structure. This generative design shell structure is possible only with 3D printing. Our industrial designer fully utilized the advantages of a 3D printed structure to present you with this magnificently artful mouse.&nbsp;Recommended filaments: Bambu PLA series<a target="_blank" href="https://store.bambulab.com/collections/bambu-lab-3d-printer-filament?gf_60645=279355719795" rel="nofollow noopener">https://store.bambulab.com/collections/bambu-lab-3d-printer-filament</a>If using PLA matte, metal, silk, please slowly screw in the bolt and avoid over-tightening to prevent structural damage.Print Setting: Print without support, v2.0 print profile recommendedHardware Kit: Wireless Mouse Components Kit-002<a target="_blank" href="http://store.bambulab.com/products/wireless-mouse-components-kit-002" rel="nofollow noopener">http://store.bambulab.com/products/wireless-mouse-components-kit-002</a>&nbsp;Please make sure you clean the build plate before printing and/or applying glue to prevent print failures.&nbsp;Follow the Assembly Guide or video tutorial below step by step to print and assemble your build. Refer to the Design Guide for further design and quality enhancement.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013716/design/2023-09-15_12b653452832c.png"></figure><figure class="media"><oembed url="https://www.youtube.com/watch?v=lkOg_X4qjW8"></oembed></figure>

Wireless Mouse 002

拓竹盲盒

cyanidesugar

Ever wanted an oversized Pikachu card with Pikachu popping out of the frame? Well now you can print one for yourself! This is another Hueforge hybrid print that uses filament painting methods and traditional 3D printing to create a combined pop-art effect piece. It's an easy 6 hour print, no supports needed! &nbsp;This print uses 4 colours, with the Yellow repeated for Pikachu at the end. If you do not have an AMS, just insert pauses at the layer swaps and manually swap out the colours :) &nbsp;It is large, at 177mm x 240mm in size. If you have to resize it to fit your printer bed, please only scale the X and Y dimensions, but do not alter the Z dimension, otherwise the layer swaps will be inaccurate. &nbsp;If you are using the Makerworld One-Click printing, all settings will have been applied to this print, and you can just hit Print. If you do not want to use that, please download the 3MF file, or the STL and apply these settings below.&nbsp;Print Instructions: <ol><li>The Hueforge portion of the print should be printed at 100% infill, at a 0.08mm layer height with 0.2mm base.</li><li>The Pikachu (and it's tail) portion of the print (from 2.04mm to 210mm height) should be printed at 5% infill with 3 walls, and at 0.16mm layer height. You can use a layer height modifier to set these settings. </li></ol>Filament Swaps:&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.2mm&nbsp;Filaments Used: - PLA Kingroon Black Transmission Distance: 0.4 - PLA BambuLab Basic BambuLab Green Transmission Distance: 8 - PLA CC3D Lemon Yellow Transmission Distance: 8 - PLA Kingroon White Transmission Distance: 8&nbsp;Swap Instructions: - Start with Black - At layer #10 (0.92mm) swap to BambuLab Green - At layer #13 (1.16mm) swap to Lemon Yellow - At layer #21 (1.8mm) swap to White - At layer #24 (2.04mm) swap to Lemon Yellow (This is for Pikachu!)&nbsp;Post Processing:You'll need to paint Pikachu's eyes and cheeks yourself, but that shouldn't take too much time!&nbsp;The Pikachu model was obtained from <a target="_blank" href="https://www.thingiverse.com/thing:3052434" rel="nofollow noopener">here</a>, by <a target="_blank" href="https://www.thingiverse.com/SAMD_Study" rel="nofollow noopener">SAMD_Study</a> and is a very cute model if you decide to print it as a standalone! &nbsp;____________________________________ Commercial License to Sell PrintsIf you want to sell any physical models I have uploaded anywhere, an unrestricted commercial license is available on the $10AUD tier of my <a target="_blank" href="https://patreon.com/cyanidesugar3DP?utm_medium=clipboard_copy&utm_source=copyLink&utm_campaign=creatorshare_creator&utm_content=join_link" rel="nofollow noopener">Patreon</a>! ____________________________________&nbsp;

Oversized Pikachu Pokemon Card - Hueforge Hybrid Print

浮雕画

AndyS1957

Ich habe den Muffler etwas flacher, kürzer und schmaler gemacht. Er wiegt jetzt weniger als 200gr. Außerdem habe ich kleinere Magnete (9Stck. 6x2mm) verwendet ( https://www.supermagnete.de/scheibenmagnete-neodym/scheibenmagnet-6mm-2mm_S-06-02-N ). I made the muffler a little flatter, shorter and narrower. It now weighs less than 200g. I also used smaller magnets (6x2mm) (https://www.supermagnete.de/scheibenmagnete-neodym/scheibenmagnet-6mm-2mm_S-06-02-N). Printer: Bambu Lab P1S, Textured PEI Plate, 0,4mm Filament: PLA (Das Filament) Layer hight: 0,24mm Perimeter: 3 Top/Bottom Layers: 3/3 Infill: 10% Gyroid Supports: no

Yet another BambuLab X1/P1 fan muffler - REMIX - 

拓竹排气消音类

Urban 3D

The updated version of this file can be found at <a target="_blank" href="https://makerworld.com/en/models/82533#profileId-87983" rel="nofollow noopener">Bambu Pull Tray Purge Bucket UPDATED by Urban 3D - MakerWorld</a> and is the one i reccomend printing as it is just much better!&nbsp;This purge bucket features a tray that is easily pulled out to empty the waste. I have also attached the .step and fusion file for easy remixing.

Bambu Pull Tray Purge Bucket

拓竹马桶类

Longracks Labs

Mashup of Dry Pods and Desiccant tray models for using desiccant beads in AMS.&nbsp;v2 in Raw Model download includes update includes:<ul><li>Plate with DryPods (0 degree offset), and trays (same as v1)</li><li>Plate with DryPod at 30 degree offset</li><li>Plate with ‘skinny’ DryPods as needed (with AMS wear preventer, etc.)  </li></ul>Drop a Boost if you are happy with this print!

Dry Pods and Desiccant Trays for AMS

爱玩的安恩恩

紫禁城

房屋类

Many24

Collection of all parts needed to make a drybox out of the famous <a href="https://www.ikea.com/cz/cs/p/samla-krabice-s-vikem-transparentni-s69440822/" rel="nofollow">IKEA SAMLA</a><h4>This collection contains:</h4><ul><li>Pneumatic air fitting holder</li><li>Magnetic box for silica gel </li><li>PTFE tube plug</li><li>Cover clips - made by <a href="https://www.thingiverse.com/thing:2110134" rel="nofollow">Wookbert</a></li><li>PVC pipe mount with outside filament holder - made by <a href="https://www.thingiverse.com/thing:743280" rel="nofollow">wstein</a></li></ul><h4>Hardware required:</h4><ul><li>Pneumatic air fitting - PC4-01</li><li>M4x10mm bolts</li><li>M4 nuts</li><li>6x3mm magnets</li><li>32mm PVC pipe</li><li>4/2mm PTFE tube</li><li>Silica gel</li><li>Humidity sensor (optional)</li><li>Seal for cover (optional)</li><li>and of course IKEA SAMLA box</li></ul>

IKEA SAMLA Drybox set with magnetic silica holder

干燥箱

Amao Chan

This is an African elephant with 22 movable joints. The joint design of this elephant is different from the common chain-like design. These joints can be adjusted and fixed at different angles, allowing the elephant's trunk to be lifted and posed in various preferred positions. The tightness of the joints depends on the hardness of the materials used for printing. Using harder materials will result in tighter joints.&nbsp;The reason it is named "Blank" is to encourage the printer to add color to the elephant's body. For those with multi-color 3D printers, they can try printing each segment in different colors.&nbsp;When printing, please start by printing the tail. If the tail can rotate properly, then use the same printing settings to print the other parts. If the tail gets stuck and cannot rotate, please reduce the material flow to continue printing.&nbsp;3D printing settings Layer height - 0.2mm Infill Density - 12% No supports. <a target="_blank" href="https://www.facebook.com/amaochanstudio/" rel="nofollow noopener">https://www.facebook.com/amaochanstudio/</a> <a target="_blank" href="https://amaochan.work/" rel="nofollow noopener">https://amaochan.work/</a>&nbsp;多關節素坯非洲象這是一隻有22個可轉動關節的非洲象這隻非洲象的關節設計與常見的鍊條式的設計不同，這種關節可以調整角度後固定，因此這隻大象的鼻子可以抬起並且擺出自己喜歡的姿態。大象的關節結緊迫程度與使用的材料硬度有關，使用愈硬的材料列印則關節的緊度愈緊。之所以取名為(白胚)的原因，就是鼓勵列印者能幫大象的身體上顏色，若有多色3D列印機的朋友就可以試著在每一段使用不一樣的色彩列印。&nbsp;列印建議 列印時請先列印尾巴，若尾巴能正常轉動，就以相同列印設定來列印其他部分。若尾巴卡住無法轉動，請減少材料流量來列印。 層高-0.2mm 免支撐 填充-12%

BLANK ELEPHANT

动物模型

Ukdavewood

This model required 23 plates to and 11 colours print and over 60 hrs printing time.A half size, simpler Single Colour 1:1000 scale version that fits on one X1/P1 plate and prints without supports is now available - and it is recommended that people look at that first before attempting this model.<a target="_blank" href="https://makerworld.com/en/models/13483?profileId=13242" rel="nofollow noopener">https://makerworld.com/en/models/13483?profileId=13242</a>&nbsp;Also, before printing this 23 plate version it is recommended you look at the smaller single A1mini plate size 4 colour version of Ventura's sister ship Azura here<a target="_blank" href="https://makerworld.com/en/models/54956#profileId-56518" rel="nofollow noopener">https://makerworld.com/en/models/54956#profileId-56518</a> <img src="https://makerworld.bblmw.com/makerworld/draft/146611/2023-11-05_f6299d4375f028.jpeg">&nbsp;&nbsp;Scale Model of P&O Cruises Ventura - for personal use only.Designed for multi colour printing on a Bambu Lab X1C or P1P with 8 Colours (2 x AMS).Designed using Fusion 360 - see video for details&nbsp;<a target="_blank" href="https://youtu.be/5GevDdOS9MU" rel="nofollow noopener">https://youtu.be/5GevDdOS9MU</a>&nbsp;Further background details about the design and printing history are available at this forum thread.<a target="_blank" href="https://forum.bambulab.com/t/cruise-ship-print" rel="nofollow noopener">https://forum.bambulab.com/t/cruise-ship-print</a>&nbsp;With some compromises on colours could probably print with one 4 colour AMS.Model is appx 250% the size of the build place - so each deck is split into sections that need to be printed separately.&nbsp;The model consists of over 400 STL files - so has been published as Bambu Studio plate level 3mf files. &nbsp;The model is designed for each deck to be printed separately in order to minimise support requirements.&nbsp;Deck sections are then joined together using dovetail joints and then each deck is bolted together using M4 Cap Head Bolts.&nbsp;Printing the model requires 21 separate 30min to 9.5 hour prints - so a total of approximately 50 hrs on a BLX1C which in my case was spread over 2 weeks.&nbsp;NB/ A smaller 1:1000 version of this ship is available which prints as one - so it is recommended that one is tried first before attempting this print.&nbsp;For the lower decks and Hull I designed it some small tabs that need to be shaved off to square off the external corners and hide the joins as much as possible.&nbsp;Also in this version of the model the radar tower on deck 18 at the front of the ships needs to be printed in separate sections and superglued together to avoid messy supports.&nbsp;A similar model of Ventura's sister ship Azura is available too which I will publish once I have received feedback on the method of publishing this ship.&nbsp;This is a personal project. I have no connection to P&O Cruises or Carnival Corporation other than being a customer.&nbsp;This version is released under a CC Non Commercial No Derivatives license due the P&O Cruises branding. &nbsp;For reference here are the filament colours I have been using in order of quantity - with a best guess at Bambu Lab equivalentseSUN PLA+ Filament 1.75mm, PLA Plus 3D Printer Filament Cold White eSUN PLA+ Silver SunLU PLA+ Blue SunLU PLA Red 1kg 1.75mm PLA 3D printer filament Printer - With coil (Gold Color) SUNLU 3D Printer Filament PLA+ Plus Grass Green Aldi Balco Blue 1kg SunLU PLA Yellow Bambu Lab Orange ICE Filaments ICEFIL1PLA104 PLA filament, 1.75mm, 0.75 kg, Barbaric Brown eSUN PLA BLACK With the quantity of white being about 10x the rest.&nbsp;My best guess at equivalent Bambu Lab Filaments to these would be:Bambu Lab PLA Basic Jade White Bambu Lab PLA Silk Silver Bambu Lab PLA Basic Blue Bambu Lab PLA Basic Red Bambu Lab PLA Basic Bronze Bambu Lab PLA Basic Green Bambu Lab PLA Matt Ice Blue Bambu Lab PLA Basic Yellow Bambu Lab PLA Basic Orange Bambu Lab PLA Basic Brown Bambu Lab PLA Basic Black &nbsp;&nbsp;&nbsp;

P&O Cruises Ventura 1:500 Cruise Ship

车船飞机

SK07 Skipper07

I present to you the new and small version of the Christmas Toy Train, I hope your children will like it too.

Christmas Toy Train

圣诞节

玩具类

ThreeD-Michael

<figure class="table" style="height:330.43px;width:90%;"><table class="ck-table-resized" style="background-color:rgb(255, 255, 255);border:1px solid rgb(230, 77, 77);"><colgroup><col><col></colgroup><tbody><tr><td style="border:1px solid rgb(230, 77, 77);padding:0.4em;vertical-align:top;width:50%;">Please also check out my latest design, a Long Range Dog Whistle at 7,000 Hz. Please download <a target="_blank" href="https://makerworld.com/en/models/376609" rel="nofollow noopener">here</a>.<figure class="image"><a href="https://makerworld.com/en/models/376609" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/718583/2024-03-17_9c74b40b64648.png"></a></figure></td><td style="border:1px solid rgb(230, 77, 77);padding:0.4em;vertical-align:top;width:50%;">I have also developed real Ultrasonic dog whistles at 20,000 Hz and above, which you can find <a target="_blank" href="https://makerworld.com/en/@ThreeDMichael/collections/876023" rel="nofollow noopener">here</a>.<figure class="image"><a href="https://makerworld.com/en/@ThreeDMichael/collections/876023" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/718583/2024-03-17_2788bf9fc9fc9.png"></a></figure></td></tr></tbody></table></figure>WARNING: This is a dog whistle and not a toy! It's very loud which can harm the ears, so please protect your ears and don't use it near other people or animals!&nbsp;This compact dog whistle produces a very loud tone of about 8 kHz. It may seem quiet to you, but that's because humans (especially in old age) perceive higher sounds less loudly or not at all - unlike many animals!&nbsp;How to print:Use a line width of 0.4 mm and a layer height of 0.2 mm, 6 top layers and 6 bottom layers.Print slowly to achieve sharp edges.

8 kHz Dog Whistle

哨子类

fay3dlab

I'm back with another suspended model Star Wars collection.. this time its the Imperial shuttle that Darth vader and Emperor Palpatine uses..&nbsp;The model was remix from aaskedall again from thingerverse.. he really has great star wars 3d models.. I remixed the shuttle using Tinkercad.. i had to redesign the middle fin of the shuttle so it can be printed without supports.. modified some parts too so it can be printed without supports.. For the frame for the shuttle to be suspended.. i designed it to look like emperor palpatine's throne.. The model is also small enough to be printed on the A1 mini but you wont have room if you want to print multicolor..The whole model is just in one part.. i also made the model to be multicolor print.. i separated the shuttle.. strings.. and the frame.. so you can pick your own color for each part..&nbsp;One important thing to remember when printing suspended models is to set the wall generator to arachne from classic.. this will make the slicer print the strings.. I hope you guys have fun printing this suspended&nbsp;&nbsp;

Suspended T-4a Shuttle

机械类模型

机动模型

搁置了许久，这次更新只是在原基础上进行修改。 1.前舱重量减小 2.后盖板根据网友（燃烧的小菊花灬）建议推出了双天线版本。 3.后盖版本推出有小孔径和中孔径，适合现有市场绝大说天线的适配 4.这次也为图传天线增添有保护件，但根据网友反馈会有图传遮挡，各位就根据使用情况选择是否选用（以下为英文翻译，本人不擅长英文，请见谅 /The following is the English translation, I am not good at English, please forgive me）Shelved for a long time, this update is just a modification on the original basis.<ol><li>The weight of the front cabin is reduced</li><li>The rear cover has a dual-antenna version based on the suggestion of a netizen (the burning little chrysanthemum).</li><li>The back cover version has small aperture and medium aperture, which is suitable for the adaptation of most antennas in the existing market</li><li>This time, a protective piece is also added to the image transmission antenna, but according to the feedback from netizens, the image transmission will be blocked. You can choose whether to use it according to the usage situation.</li></ol>

DJI O3 CAM(O3 air unit)third edition

喵武士

由于我的设计的习惯是尽量减少打印时候的支撑和五金件的使用，因此设计大都采用了利用公差直接连接。由于打印机的误差和不同打印机以及材料的关系，难免有一些过紧或过松的情况，可能有一些地方大家需要打磨下，或使用双面胶收紧一下。&nbsp;需要使用4个686轴承和3个106轴承，一点点羽毛球缠把的手胶，一点点双面胶。具体安装方式请在B站上查看视频，以下是简明的安装说明：<a target="_blank" href="https://www.bilibili.com/video/BV1dg4y1Z72X/?spm_id_from=333.999.0.0" rel="nofollow noopener">https://www.bilibili.com/video/BV1dg4y1Z72X/?spm_id_from=333.999.0.0</a><figure class="media"><div data-oembed-url="https://www.bilibili.com/video/BV1dg4y1Z72X/?spm_id_from=333.999.0.0"><div class="ck-media__wrapper" data-oembed-url="https://player.bilibili.com/player.html?bvid=BV1dg4y1Z72X&autoplay=0&poster=1"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://player.bilibili.com/player.html?bvid=BV1dg4y1Z72X&autoplay=0&poster=1" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure><ol><li>首先来连接前后轴<ol><li>由于要免支撑打印，因此在做这个转轴的时候才用了这个分离的结构，这样对准卡口放进去，用钳子稍微旋转，感觉紧了就可以了，不要过于用力，不然就拧秃噜了；</li><li>然后扣上这个686轴承待用；</li></ol></li><li>下面我们就用到这2个106轴承：<ol><li>1个扣到这里，预留的公差比较小，可以用个镊子或改锥什么的借个力。</li><li>另外两个同样方式，扣到这里。</li></ol></li><li>下面我们来装齿轮<ol><li>这个驱动齿轮公差留的比较小，安装前要先插上去再拔下来试下；</li><li>然后这样安装到位，悬空的这块先放着；</li><li>锥齿轮也是先把这个轴插拔一下，有时候由打印机的抖动，中间会偏粗，因此有需要的话，可以稍微打磨下；方法也很简单，可以用砂纸，我一般是用钳子这样撸几下就可以了。</li><li>然后压入第3个106轴承，尽量压到底，然后放入这个小的C型环，用来限位置。</li><li>最后用轴承连接上，转一下试试。</li></ol></li><li>然后我们把安装好的转轴压入。这里是参考了拓竹AMS的设计。为了限定转轴位置更准确，这里修改了设计，加了一个小的台阶，因此安装的时候要稍微向外侧掰一点点。</li><li>然后我们把支撑架放入开好口的干燥箱。然后用这个轴套连接。那这两个小的垫片是做什么用的呢？由于干燥箱的侧面不是完全垂直的，有一点点角度，因此可以选装这个垫片，可以让接口的地方更平整。</li><li>如果有对密封性要求比较高的话，这里可以用点胶或加一些TPU的垫圈都可以。</li><li>然后装上可拆卸的旋钮就可以了。上次有网友提出可以用手柄，很好的想法，但我懒得设计了，哈哈，主要这里空间有限，这次加大了旋钮的尺寸，感觉也挺好用的。</li></ol>

可回卷干燥箱耗材架 Rewindable Filament Drybox

工具类

HribaDesign

The containers are composed of one or more hexagons with a basic size of 5 cm.All are available with a smooth or wavy bottom.

Catch-All Trays / Hex organizer

盒子类

Office.3D

Unicorn Lightbox Led Lamp

灯箱

The-Owl

The 3D-printed display surround for the Bambulab P1S seamlessly blends functionality with aesthetics, offering a unique Nintendo-inspired design. Crafted from high-quality, durable plastic, this surround not only provides additional protection for your Bambulab P1S display but also infuses it with a playful Nintendo flair reminiscent of the iconic gaming consoles.Carefully designed to capture the characteristic features of Nintendo devices, the clear lines and vibrant colors pay homage to Nintendo's iconic design language. The precise fit ensures that the surround sits snugly around the Bambulab P1S display. Ergonomic cutouts provide easy access to controls and ports, maintaining the device's functionality without compromise.Beyond being a protective accessory, the 3D-printed display surround serves as an expression of your gaming passion in Nintendo style. Whether you're a longtime Nintendo enthusiast or simply appreciate the cult design, this surround transforms your Bambulab P1S into a personalized statement piece. It not only shields your device but becomes a conversation starter, showcasing your love for the gaming world.Indulge your Bambulab P1S with this exclusive 3D-printed display surround, marrying protection and personality in the Nintendo aesthetic. Whether you're playing on-the-go or displaying your device at home, this surround adds a touch of nostalgia and style to elevate your gaming experience. Embrace the perfect blend of protection and individuality with this unique Nintendo-inspired accessory. -Made with chat Gpt :D

Bezel P1s NinBAMBU Display Umrandung P1s im nintendo design Faceplate

钥匙扣

Saber3D

*Light Fury not included*&nbsp;Check all my models out at <a target="_blank" href="https://saber-3d.com/" rel="nofollow noopener">www.Saber-3D.com</a> &nbsp;Follow our socials to see new models! &nbsp;<a target="_blank" href="https://www.instagram.com/saber.3d" rel="nofollow noopener">https://www.instagram.com/saber.3d</a><a target="_blank" href="https://www.tiktok.com/@saber3d" rel="nofollow noopener">https://www.tiktok.com/@saber3d</a> &nbsp;Flexi Toothless can Stand, Sit, and Flap Its Wings!&nbsp;It is a great print for those who love to fidget. It does not require supports and prints well in PLA.&nbsp;No Supports necessary!&nbsp;Not all filaments are created equal, If your having issues with wing joints, I suggest increasing or decreasing wing size by 1% until you have the desired fit.&nbsp;For personal non-commercial use only. Please do NOT redistribute the files to anyone else.&nbsp;Want to sell prints or just enjoy the instant access to all my models? join our All Access tier on <a target="_blank" href="https://www.patreon.com/Saber3D" rel="nofollow noopener">Patreon</a>. &nbsp;We really appreciate your support!&nbsp;Please share images of your prints, we love to see them!